Search results: n4

RotorRiot Vision40 Prints

Print files for the Rotor Riot Vision40

Jonsbo N4 - 2x SLIM Fans Front Adapter

This is my addition to the Jonsbo N4 case to keep disks at safe temperatures. The magnets used are 2 mm thick and 8mm in diameter (4mm radius). The fans used are: ARCTIC P12 Slim PWM PST 120x15 Printed on Bambu Lab P1S with a black matte…

Canister Spout with Vent – DIN45 / DIN51 / DIN61 / DIN71

This pouring spout is designed for canisters with DIN threads , commonly found on 10 L and 20 L canisters . An integrated air channel allows air to flow back into the canister while pouring, resulting in a smooth, controlled stream and…

Absperrschieber Absaugung fuer HT-Rohr DN40 / Blastgate Suction for HT pipe DN40

Ein Absperrschieber/Blastgate für eine Absaugung mit HT-Rohr DN40. Zusätzlich werden 4 kleine Schrauben benötigt, um die Teile zusammen zu schrauben. Nicht zu fest anziehen, sonst gleitet der Schieber nicht mehr richtig. Das Teil1 muss…

DIN45 canister cap

I'm too lazy to buy this things. Canister cap with 1/2" inside thread for my campervan. Designed for print without supports. I print with Prusament PET-G Orange.

Operation Wolf Assault Weapon - Gun Shell- for GUN4IR

Incase Prusaprinters glitches out again you can find it also here: https://www.thingiverse.com/thing:4881488 This gun shell is a replica from the Operation Wolf Arcade game. It is assembled much like it's sheet metal and steel father, but…

Bed Screw Lock for N4 Pro (2024 model) - updated

Update 8.10.2024: new slim variant that seats better to the counterpart, still holds and its much nicer to adjust the screws I have bed with cutouts and its 7.5mm thick so every other variants of this part failed. Other problem is that…

Spout canister DIN45

Hello, this is a remix from the canister spout to fit canister with a DIN45 thread. They fit on my canister with 2,5 L and 5 L. The cap ring I got from https://www.thingiverse.com/thing:2484159 , it fits very well. Category: Household

Jonsbo N4 - 2x SLIM Fans Front Adapter - REMIX

Remix of the “ Jonsbo N4 - 2x SLIM Fans Front Adapter ” This version uses 10x2mm magnets. STL available as one piece or two pieces. Used the same fans as the original ARCTIC P12 Slim PWM PST 120x15 (affiliate link) Printed on Bambu Lab…

LilyGO T-CAN485 case

Small case for the LilyGO T-CAN485 ESP32 board. Top held on by press-fit, bottom can be mounted to something using double-sided tape (don't print on a textured bed if you plan on doing that). Be aware that for CAN and RS485 the DC-DC…

Frosterfach-Offenhalter für Thetford-Kühlschrank N4142E + Version 2

Ich habe mich immer geärgert, dass das Eisfach des Thetford-Kühlschranks nicht offen blieb, wenn wir das Fahrzeug in den Winterschlaf geschickt haben. Natürlich geht auch ein Korken. Diese Ecke bleibt aber, wo sie hin soll. Mein…

DIN45 Schraubverschluss / DIN45 screw cap

Meiner Version eines DIN45 Schraubverschluss. Passt auf ein 5L Isopropanolkanister. ________________________________________________________________________________________________________ My version of a DIN45 screw cap. Fits on a 5L…

Casing for lilygo T-CAN485 and cable management holder for Marstek Venus

An enclosure for the lilygo T-CAN485 with visible LED and access to boot and reset buttons. A holder for the enclosure with cable management and a hook to attach the assembly to a Marstek Venus battery.

Rugged box for DJI Osmo Action4

Rugged box for DJI Osmo Action4. All parts (except handle) of the adventure kit can be fitted into this box. The lens protector in the picture is this model: https://www.printables.com/de/model/694351-dji-osmo-action-4-cam-cover

Jonsbo N4 - Slim Front Fan Adaptor & 120x25mm fan version

Large bed only. (6/2/2025): added 25mm height fan model Print with support.

knurled-Bolt-Nut-DIN466 / Knob / Hohe Rändelmutter DIN466 M3, M4, M5, M6, M8, M10

DE Eine praktische hohe Rändelmutter oder Rändelschraube nach DIN466, Größen siehe Bilder Das Modell lässt sich ohne Supportmaterial drucken. Die 0,2 mm dicke Schicht lässt sich einfach durchstoßen. A useful high knurled nut or knurled…

DIY SATA backplane for Jonsbo N4

UPDATE: I slightly tweaked the HDD baseplane, now the hdd slides perfectly. Every tenth of a millimeter counts. UPDATE 2: I modified the HDD part and removed the extrusion. I uploaded the full fusion 360 file under the name v2.1, and the…

Russian PMN4 APERS Mine ordnance replica

Anti-personnel mine. makes a great desk ornament or nice training aid. Print the landmine top in a flexible filament for authenticity. MILSIM LARP ASG

40oz Water Bottle Holder for 2020 (Gen4) Mazda 3

The cup holder position on this car didn't allow me to use the standard cup holder extension with my favorite water bottle so I made this. It's not perfect but it's more than good enough for me and holds my water bottle. Might tweak it…

Bosch e-bike Gen4 Spider Lock Ring Tool MJ 21/22 Chainring Nut

Here is a model for a tool to loose or tighten the nut on an Bosch E-Bike Gen4 chainring. I printed mine in PETG, this is quite sufficient. Due to the fine thread, too high torques should not be used here anyway. Use with an ½ inch…

DN40 Standby Dock – MagSafe, Apple Watch & Extra Wired Charging Slot - by overwerk and Scott Yu-Jan. Dieter Rams inspired. for Iphone 15.

DN40 Standby Dock – MagSafe, Apple Watch & Extra Wired Charging Slot Upgrade your nightstand or desk with the DN40 Standby Dock ! This 3D-printed dock is designed for iPhone Standby Mode , MagSafe charging, and Apple Watch, plus it…

Astro A50 Gen4 Headband Fix

Due to my wide head the headband cushions clipped out of place. This thing is designed with Freecad 19 and works for my 4. gen Astro a50 Headphones. Issues: After 4 Months of usage the plastic wobbled around so much that it left scratches…

1N4148 diodes bending jig

Very simple design: this jig allows to bend quickly and repeatedly diodes for the Redox keyboard PCB. Print instructions Category: Electronics Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 150µm…

DIN45 canister cap with hole

The " Spout Canister DIN45 " fits the hole in the remixed " DIN45 Canister Cap ". I've found the other cap to be better than the original spout cap, so now you have a choice of two.

iPhone 17 DN40 Dock - Original Silicone Case- Made by: ScottYu-Jan and OVERWERK

Thanks to the amazing work of ScottYu-Jan and OVERWERK we have a cool stand for the iPhone. Marlfox did an amazing job by using parameters in Fusion to be able to adjust the size. What i did here is just figuring out the best size for the…

FRX style electric guitar, 7 string multiscale RedRaven4

My design of 7 string multiscale electric guitar, ESP FRX style. Harley Benton R-457BK Fan fret was used as donor guitar. Cheapest way to get 7 string multiscale neck. Bridge is something from AliExpress (originals can be used), pickups…

Lockring tool for Bosch Gen4

It has a thin “lip” so it can engage fully with the Sram boost chainrings as they have an offset. I can be used with a 3/8" driver. Printed in PETG it is strong enough for the required torque. Print settings Material: PETG Resolution:…

Vacuum Valve (Unterdruckventil) 50mm (DN50) +more (DN75/DN40)

If you are looking for a vacuum valve to be installed directly in your 50mm (DN50) pipe installation you might find this thing very helpful. As an example if you use one of those cyclone dust separaters and fear that your holding tank…

Pig - Version4 - Matryoshka

This "nesting pigs" are Version 4 of four pig prints as follows: V1 : plain pig V2 : piggy bank #1 with slot only V3 : piggy bank #2 with slot and bottom opening V4 : Matryoshka pig(s) All versions use the same basic design, with some…

Jonsbo N4 - 2x STANDARD Fans Front Adapter - Remix

2 Part front adapter to add standard pc fans ot the front of the jonsbo n4. Printed on Bambu Labs A1 mini with tree supports.

Fx Impact GEN4 Magazine cal.22 x 30 rnd

Proved FX Impact Extended GEN4 magazine for 30 x 5.5mm (.22) pellets. You will need to build a suitable spring or adapt one by modifying its connection to the case and crown. A spring of 19 mm x 0,02" is recommended. This model, unlike…

NEJE N40630 (30W) Laser Air Assist (.stl & .step)

This model is a drop-in replacement for the laser module's tinted acrylic window and slides directly over the laser's focusing lens. To achieve an airtight fit around the focusing lens, it is recommended to apply a few turns of Teflon…

Nikon N6006 / F-601 Film Door Latch Replacement (also fits N5005, N4004 / F-401, F-401X)

The film door latch on the Nikon N6006, N5005, and N4004 (F-601, F-401X, F-401) is notorious for breaking. Replacements are often over $10 for a piece smaller than a fingernail, so I modeled one and want to release it for free! This…

Jonsbo N4 Slim Front Cover with fans

Printed with Bambu lab White ABS on a Bambu lab X1C The current solutions using extensions don't look very appealing, so I decided to design a front panel that accommodates fans - it's a complete replica of the original, except for the…

Standard DN40 to DN35 Adapter For Kärcher Industrial Line (40mm to 35mm)

I designed this for a Parkside wall-based vacuum sucker to be compatible with my Kärcher NT 70/3 Me Tc vacuum, that uses the thicker DN40 (40mm ID) standard instead of the DN35 found in household vacuum cleaners. I recommend deburring the…

Alexa Echo Gen4 Stand for Skadis

I needed a stand to put my daughters Echo Gen 4 on her Skadis board. I've found a great model for a french cleat here: https://www.printables.com/de/model/495363-amazon-echo-4-french-cleat-hanging-system I have printed the model in PETG…

osVAC neo DN40 to M32 and DN40 to F32

osVAC neo adapter DN40 to M32 osVAC neo adapter DN40 to F32 DN is parameterizable (35 - 45) using Fusion 360 Print Settings Printer Brand: ELEGOO Printer: ELEGOO NEPTUNE 3 Pro Rafts: No Supports: No Resolution: 0.3 Infill: 50% Filament:…

Magazine base plate for UMAREX glock 17 gen4

Magazine Base Plate for UMAREX Glock 17 Gen4 – a precisely designed replacement part for Umarex Glock 17 Gen4 replicas. It ensures durability and secure fit. Perfect for airsoft enthusiasts and replica owners seeking reliable spare parts.…

osVAC neo M32 DN40

osVAC neo adapter M32 to DN40 DN is parameterizable (35 - 45) using Fusion 360 Print Settings Printer Brand: ELEGOO Printer: ELEGOO NEPTUNE 3 Pro Rafts: No Supports: No Resolution: 0.3 Infill: 50% Filament: Geeetech PETG white…

37mm Lens Filter Adapter for VanTrue N4 Dashcam

Certain versions of the VanTrue N4 dashcams do not have the mount for the CPL filters they (and other third parties) sell for these cameras. This model fixes that, allowing for any 37mm lens to be attached to the camera. The adapter is…

DN40 - HT40 VERSCHLUSS KAPPE MUFFE END / CAP CLOSURE SEALING CAP PIPE TUBE

German: Verschlusskappe zu DN40 Rohren, Verschluss bzw. Endkappe. Einmal mit Schrift "DN40" einmal ohne.. geeignet zum Verschluss von Rohren, als Endstück. Abmessungen: Passend zu DN 40 Rohren, Materialstärke 2mm Andere Dimensionen in…

【Pikmin4】Cable grommet Bulb box v1.2

Set contents: 1 cable grommet (assembled) Size: Inner diameter Φ60mm, compatible desk thickness 15mm Material: PLA (polylactic acid) Color: Blue, orange, gray (base is black) Printing: Approximately 4.5 hours/1 piece Lamination: 0.06mm…

Deckel für Abwasserrohr DN40, DN50, DN75

Der Deckel passt auf HT/KG Rohre der Größe DN40, DN50, DN75

Time Crisis Named Lightgun Gun4IR GX16 adapter

This is for people who want to modify a Time Crisis 1 clone arcade lightgun to use a GX16 connector and their own cable instead of the fixed shower hose that comes with the gun, without having to widen the original hole. Model should be…

Cable holder Elegoo N3 - N4 series

Print in place - Support Free

Cooler Master N400 Toolless HDD Bracket

EDIT: I've updated the model to have better hole support for the roof around the central locking pin. I've also uploaded the .STEP file version for easier editing if people need it. This is a reproduction of the tool free hard drive…

Parametric Pipe Plug for Sewer Pipes (DN32, DN40, DN50, DN75, DN90, DN110)

This is a parametric pipe plug designed for sewer / drainage pipes with rubber seals (HT / KG systems). The model is generated using OpenSCAD and supports pipe sizes from DN32 to DN110 . For convenience, I have also included pre-generated…

Jonsbo N4 60mm Fan mount

Hey, I was trying to improve the airflow in the drive bay of my Jonsbo N4 Homeserver case, and I saw that there is a vent above the PSU, and since air takes the path of least resistance, I assume that a lot of the air being sucked out by…

Acer Veriton N4640G PCIe addon

Have you also been searching for addon slot for PCIe card for your Acer Veriton N4640G? Look no further, this model is made to acuminate any single slot, low profile PCIe card. If you are looking into adding some networking card or even…

Eufy E340 Doorbell faceplate/cover - New Version4

IMPORTANT New Version 4 New version has ports for the IR illuminators and a larger port for the the ring button so you can see the light around it. I just installed the Eufy E340 and so far I really love it, except it's so UGLY. I miss my…

Gun4IR GCON45 Solenoid model 0530 Support

This is a no cut mod support for a 0530B solenoid model to fit in a Namco GunCon 45 made to be compatible with Gun4IR official PCBs. The model is composed of two parts that are glued together on their flat surface for printing without…

Fenders for RC Car MN45 scale 1:12

Fenders for RC Car MN45 scale 1:12 WPL Toyota Landcruiser

Neje N40630 Air assist

Air assist option for the NEJE N40630 laser with access to focus wheel. fits 5mmOD 2.5mm ID air assist tubing (tubing has air tight fit around inlet so no glue required) this was inspired by a few creators models but did not suit my needs…

Jonsbo N4 front panel

I don’t like the wooden front panel of this case — it doesn’t match my interior design or aesthetic preferences at all. That’s why I made a plastic one to replace the original. The PEI coating on the 3D printer bed gives the surface an…

Parametric connector for 20 mm DN20 empty conduit / Leerrohrverbinder DN16 DN25 DN32 DN40

Connects two 20 mm outer diameter empty conduits. Print without support. Don't forget to add a brim to make it stick. With stop lip inside - overhang-friendly chamfered design for support free printing - to prevent one of them from…

DN40 Iphone 13 mini dock without button

I remixed the model for anyone who prefers the Dock without the button

CAA Micro Roni gen4 wall mount

Simple wall mount for the Micro Roni Gen4 I used 4.5 x 40 mm screws to fix it on the wall. Print instructions 4 walls, no supports, 10% infill.

Vacuumdapter DN50/DN40 to hose inside 38mm

Saugerdapter DN50/DN40 zu Staubsaugerschlauch innen 38mm Das Gewinde sitzt sehr fest und dichtet sauber ab Vacuum cleaner adapter DN50/DN40 for vacuum cleaner hose inside 38mm The thread is very tight and seals cleanly

IBC tank DN40 connector with HEX

English To connect my IBC tanks to each other, or to realise a simple overflow, I created this simple connection. A 35mm hole in the tank is more than sufficient (I like to use a step drill for this), a standard seal from the DIY store…

Stopfen für HT-Rohr DN40 / Plug For Drainage PipesDN40

Ein Stopfen für HT-Rohre der Dimension DN40. Mit PLA sicher nicht hochtemperaturfest (HT). Auch für die benötigte Dichtigkeit müsst Ihr selbst sorgen. Aber als Geruchsverschuss allemal geeignet.…

PlayStation4 Camera Stand

PS4 Camera Stand. Height variation:1mm,10mm,30mm,60mm See this site for more information. Sorry, This site is Japanese only. ( https://kitto-yakudatsu.com/archives/1544 ) Print instructions Category: Video Games Print Settings Printer:…

【Pikmin4】Vase pen stand+bonus v1.3

Set contents: 1 large and small pen holder + bonus Size: diameter 32mm/44mm, height 75mm/100mm Material: PLA (polylactic acid) Printing: Approximately 2.5 hours/1 piece, approximately 3 hours/1 piece Lamination: 0.08mm Please use it as a…

CAA Micro Roni Gen4 Bump Stock Extender 50mm

🔫 Introducing the Bump Stock Extension for Micro Roni Gen4 by Veracon Engineering! Enhance the stability and control of your Micro Roni Gen4 with our custom-designed Bump Stock Extension. Engineered for precision and compatibility, this…

LilyGo T-CAN485 Case

Protect your LilyGo T-CAN485 with this simple enclosure. Printed fast with a .6 nozzle, so the example is a little rough around the edges. Fusion 360 file included for modifying to your specific needs.

Nálevka pro kanystr se zavitem DIN45

Nálevka pro 5l kanystr se zavitem DIN45 / pro nalévání kapaliny do hazerů a mlh samostané víčko je možné použít i jako držák trychtýře rozměry víčka : 45mm vnitrni průměr , 32mm díra pro nálevku a trychtýř Tisk: Material : PETG výplň :…

Jonsbo N4 slim fan 120m modded

Printed with White PLA+ eSun (230°/60°) on a Creality Ender 3 V3 SE. The goal was to make a first prototype before doing it in PETG or another material more suitable for a computer piece. For now it fits very well and can hold fans. I…

Cloche filtre à huile BMW e46 moteur n42 (86mm 16 pans)

Bonjour, Voici la cloche de 86 mm à 16 pans pour le démontage du filtre a huile sur BMW e46 équipée avec moteur N42B18A. Prévue pour clé dynamométrique avec carré de 12,5mm. Pièce conçue pour être solide Tolérance à 0,1mm Pas de support 5…

bmw n47 Cam locking tool

simple locking tool for the camshaft on BMW n47 engine models DON'T expect it to hold when tightening the bolts on the camshaft. just print it with high infill in what ever material you wanna use

Shelly Gen4 DIN rail mount with space for 6 WAGO 221 clamps

This model is designed to hold one shelly of generation 4 (may be some of gen3 are fitting, too). The shelly is held in place and can never fall of. Just put it in and slide it to the front (down on my photo). After installing all cables…

Begode MTEN4 EUC Stand

I remixed a popular EUC Stand to be one single unit (Assembly no longer needed) and resized it to fit the Begode Mten4. The wheel doesn't sit perfectly but would stay in place and not tip over when knocked from the side. For best result,…

Rohrverbinder EN40

In meinem Haus habe ich ein Elektro-Leerrohr mit 40mm Durchmesser vom Dach bis in den Keller für eine Photovoltaikanlage verlegt. Auf den Dachboden ist das Rohr unterbrochen um ein leichteres Verlegen zu ermöglichen. Verbinde wollte ich…

Gun4IR JF-0530B Solenoid Support for Guncon 1

I recommend using tree support for the TMP36 holder bridge so the support is not really affecting the TMP36 sensor slot. Insert the TMP36 sensor from the inside by passing the legs through the opening before installing the solenoid

Gun4IR GunCon 2/G-Con 2 Solenoid model 0530 Support

This is a no cut mod support for a 0530 solenoid (without the rod) model to fit in a Namco GunCon 2 made to be compatible with Gun4IR official PCBs. Solenoid model 0530 comes in different varieties 0530, 0530B, 0530T. The two with the B…

Milwaukee M18 Fuel Gen4 Impact Driver Bit Holder

This bit holder allows you to attach 3-4 hex bits to your M18 Fuel impact driver. This model will work on both regular (2953-20) and surge (2761-20) version of Gen4 Fuel impact drivers. Includes versions for 3 and 4 slots as well as left…

Jonsbo N4 - Dual 120mm Fans Cooling Mod

This is a mod I created for the Jonsbo N4 case. There are already some great mods to help with cooling, but none of them help with airflow out of the top of the case. This mod allows for two 120mm fans to be installed on top of the…

Morse Code Paddle by JN4JXL

Parts Bearing: MR117ZZ x 4 Magnet: 5x1mm Neodymium magnet x 6 Screw: M3x10mm x 20 Flat head tapping: 3x8mm x 4 Wire: 0.2mm Mag Print finger_piece x 2 spacer x 2 selece side_hole_frame or back_hole_frame x1 other x 1

Hose connector 24mm hose to DN40 pipe (40mm)

The adapter is designed to connect a 24mm hose from a rain colector (like this ) with a DN40 pipe I printed it with PETG and it works fine since I installed it three months ago.

Specialized Turbo Levo Gen4 Wall Charger Mount

When I bought my Gen4 Turbo Levo I couldn't find any wall mounts for the charger to keep it off the floor so here you go. The arms can hold both charger cables if needed. Screws: I used SnapSkru SPM Mini #6 I think, but any smallish screw…

Begode Mten4 Headlight Bumper

This is a bumper for the Mten4's headlight. It is designed to allow a fuller range of adjustment on headlight angle, while also providing protection. Tabs that hook over the headlight screws help to prevent the bumper from being ejected…

Webcam support for N4P

This camera support is suitable for Neptune 4 Pro

WIG / TIG filler rod / welding wire HT DN40 organisation system

I cut a 1 meter pipe into two parts. The lower part is 80 cm and the upper part 20 cm. You need: 1x Wandhalter Boden (Wallmount bottom) The diameter of the holes are bigger than the pipe's diameter because it has to fit the lid (Deckel)…

LINKUP Ultra PCIE 4.0 Gen4 Riser Cable Mounting Base Plate Support (for Corsair iCUE 4000X/4000D/5000D & maybe other cases)

If you find my designs useful, please consider sending a tip I recently mounted my GeForce RTX 3080 vertically in my Corsair iCUE 4000X case using the Linkup PCI-E 4.0 Riser Support cable but I was concerned about how much the Riser's PCB…

Astro A50 Gen4 (A00085) Headband to Headphone Mount - Right Side

This is a replacement part for the Astro A50 Gen4 (A00085) for the right side mount that connects the headband to the headphone slider arm. This model is slightly different from the original mount. It is slightly thicker at the bottom…

PlayStation4 Camera Clip Holder

This is the Clip Holder for PS4 Camera on TV. See this site for more information. Sorry, This site is Japanese only. ( https://kitto-yakudatsu.com/archives/1441 ) Print instructions Unassociated tags: PS4 Camera Category: Video Games…

Bottle holder for Thetford N4241 / N4000 fridge - Fusion360 remix

Thanks to @Creo2005_265049 for providing the base with the f3d file. I changed it to fit Thetford N4241 / N4000 caravan fridge. To illustrate the dfference, on the first pic this part is clipped into the N4241 shelf, the original from…

Attachment for rear parcel shelf of BMW 3 series (N46 hatchback)

Requires support on build plate only. Should be printed with ABS, ASA or any other temperature resistant material.

Halter für Motorola PMMN4040A Mikrofonlautsprecher

Lochdurchmesser: 4,5 mm (für Montage)

Vision40 canopy O4 Lite with Flywoo Camera Shell and ND filters

Ugly file but prints fine, use tpu and supports

Case for LilyGo ESP32 T-CAN485 module

This minimalistic case for the nice CAN-bus and RS485 interface ESP32 board of LilyGo named LilyGo ESP32 T-CAN485 has a snap-on top with holes for the RGB-led and the Reset and Boot buttons. The sides of the case have openings for the…

N4m-KCM mount

Mount the coPrint KCM module on the Neprune 3plus/max and 4plys/max models. You will need to replace the screws with longer screws

Side bumpers for RC Car MN45 scale 1:12

Side bumpers (steppers) for RC Car MN45 scale 1:12 Toyota Landcruiser

Essende Person4/Eating person4

.

PlayStation4 Camera v2 (round) tripod mount

This is a tripod mount for the second-generation PlayStation4 camera - the round-bodied one. (aka ps4eye or psvr camera) The stand it comes with is good for mounting on a TV or monitor, and on some tables, but for more flexibility a…

Jonsbo Hard Drive Screw Grommet for N1 N2 N3 N4 N5 cases

My buddy grabbed a Jonsbo N4 case second hand, missing nearly all of the hard drive grommets, but we had the screws. Threw together a print, and used TPU 95A to print them out. Works great for that OEM feel. From the look of things, this…

M-Audio Oxygen49 Midi Keyboard Wall Mount

Mounts are positioned for printing, no supports needed. Examples in pictures are printed using PLA Plus at .28mm layer height and 15% infill. I used 3 mounts total to hold the keyboard. They are designed to fit into the open space on the…

MN45 truck bed frame scale 1:12 WPL

MN45 truck bed frame scale 1:12 WPL Toyota Landcruiser

Hakko B2756 Tip Tray T9/T15/T16/T22/T30/T31/T33/T35/N3/N4

Just like the original Hakko B2756 but you can print as many as you need now. I printed with 5 walls, 0.2mm height and 80-100% infill to add some weight to it. I debated adding a lead weight to it but with the tips in it it has enough…

ESP32E-N4 IR Blaster / Receiver Case

This is a compact, functional enclosure designed specifically for the ESP32E-N4 IR Blaster / Receiver board . It features a minimal footprint, toolless assembly, and precise cutouts for operation and connectivity. Features Snug Snap-Fit…

W3STF4LIA V4N4G0N Keyboard Case

A V4N4G0N Keyboard case with a handle to throw it away if you lose in the game. It's compatible with V4N R3 PCB and Monorail.

AIR ASSIST NEJE LASER N40630