Counting matching models…
I constructed this board to hold the above mentioned controller for development purposes. The part was printed with PLA with a layer of 0.3 mm. Any other filament works too. No rocket science. Step file included. F360-file on request. The…
Enclosure for a NodeMCU ESP8266 development board. The model fits boards with measurements being roughtly 26X49mm. The model is designed so that 5 Wagu 221 connectors can be mounted for connecting the LED-strip through a hole en one end…
A case for housing a NodeMCU (ESP8266) board with enough room for cable management. I added holes on both sides to get your sensor cables out of the case, if needed. The case is also high enough to house all of your cable mess. Walls are…
Enclosure for a NodeMCU ESP8266 board. Allows space for connections onto the male header, with a small cable exit. Also allows access to the USB port. Use two short M2.5 countersunk screws to hold the lid in place. This also clamps the…
A minimalist housing design for OpenDTU, providing component visibility and accessibility for maintenance Additional components: 1,3 Zoll OLED display ESP32 NodeMCU NRF24L01+
Since I could not find a case to fit my Plusivo NodeMCU v0.9 boards, I adapted one. The ideea is based on two Tinkercad designs: The cutout in the top of the case (I re-used this for the cutout) :…
A snap-on case for a NodeMCU v3 that has slots for USB charging and sensor wires. Designed to fit DuPont connectors attached to the NodeMCU's pins. This was my first basic case for my DIY Home Assistant setup. I use it hold SHT3x-D…
This is my small case made for an ESP8266 NodeMCU board. It can be usefull for IoT or smarthome aplications, where the ESP doesn't need to have many connections apart from the USB cord. The Model also comes in some variations (e.g. an…
This case is designed to house a NodeMCUv3 (ESP8266) development board with a Sensorion SCD30 CO2 sensor. It can be used with any other sensor that fits in the open space above the NodeMCUv3 board, though. The case has built-in slots to…
Case for my NodeMCU (ESP8266) which I'm using together with DS18B20 to measure temperature in the swimming pool. On the ESP is running ESP Home reading temperature from DS18B20 and sending it to the Home Assistant when it is processed and…
About: Remix of Multisensor ESP32-WROOM-32 NodeMCU ESPresense by teaser : Added camera hole (10mm hole) Expanded area for extended builtin wifi antenna on modern nodemcu boards that protrudes outside of the dev board Wider hole to connect…
This is n-th version, holds well, board "click’s" into position. I'm also using it as the part of final case fitting.
An ESP8266/NodeMCU enclosure incl a JST connector for a LED strip, a barrel connector for DC power and 4 dupont connectors. Used this for the other part of the dupont connector:…
The lid snaps in, just screws for mounting the electronics required.
This is case for a NodeMCU Lolin V3 Module ESP8266 board, 1x DHT22 sensor and 1 or 2 x Aviation connector to connect other sensors. No screws are required. The cover is simply pressed onto the housing. I don't use supports for printing. I…
A sealable case for the NodeMCU ESP8266. Mounting screws hold in place while the lid snaps tightly on top and wont come off easily. This can be used standalone or as part of a larger project or design. This thing was made with Tinkercad.…
Simplistic case for esp32 (devkit c). It has a snug fit for the esp, pin and usb breakout and lets you easy remove the esp board. The case itself is meant to be glued together. The purpose was mainly for my private projects, but I wanted…
Fusion 360 source file available! UPDATE 27.03.19: Remodeled designs from scratch in Fusion 360 and added slots to fit full size dupont connectors as follows: V2 - similar to the original but with duponts V2_Hollow - hollow bottom, more…
This case allows you to put the dupont wires inside the case rather than outside (in case you have a cat that likes to knock your stuff around). It provides a bit more security to keep things from being disconnected.
Needed a case and didn't find one I liked so I designed my own. I wanted something very minimal with thinner walls to reduce print time and material used. There is a port on the bottom of the case for wires to feed through as well as a…
just a stretched version fitting ESP8266 nodeMCU v3 from https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/samwiseg0/esp8266_nodemcu_din_mount by samwiseg0
Hello friends this is a simple case the Node MCU (ESP 8266). Route the cables through the case bottom before you solder them to the Node MCU. Support is needed for the Case Bottom. Print Settings Printer Brand: Creality Printer: Ender 3…
I liked the case plasmata designed, but needed more space beneath for easier pin access. This version provides more space and an unnecessary vent on the lid. ***UPDATE: Added a base version with two holes for wire access.
My first take on building my own sensor for presence detection in our rooms. All cases I tried either didn't fit the board or weren't able to house the sensors. So I designed one myself. It fits the AZDelivery ESP32 NodeMCU…
This is my rendition of a case with lid for the ESP32 S2 NodeMCU board to house the DHT11 temperature and humidity sensor. This model also have the Home Assistant logo embedded on the side. This simple design ensures a tight fit for the…
There are 3 parts to this. The top, bottom and an accent colour board (for some extra fun). The design doesn't serve too much of a practical purpose (the hexagons look cool) but, the pins are recessed into the case to prevent them from…
A remix scaled up a bit to fit an ESP32 nodemcu Category: Electronics
This is a remix of an original terminal for a Wemos D1 Mini. Since I am unfortunately a total novice with regard to soldering, I was looking for an equally nice looking terminal, without the need to solder. I increased the depth of the…
I wasn't entirely happy with other models, so I created my own. minimal size to protect all header pins cutouts for USB port, the 2 buttons and Dupont connectors You just need 2x countersunk M3 screws or friction fit the top (for this you…
This is a case for the NodeMCU ESP-32S development board by Ai-Thinker that can be mounted on an Ikea Skadis pegboard . It uses Skadis T-Nuts for secure and easy installation. Note: This was made for the Micro USB version of the board and…
The purpose of this project is to create an inexpensive audio player for home assistant that can be plugged into an existing stereo speaker system. With this system, you can also build a simple mono amplified speaker that can be used as a…
This is my rendition of a case with lid for the ESP32 Devkit V1 NodeMCU board to house the DHT11 temperature and humidity sensor. This simple design ensures a tight fit for the ESP32 Devkit V1 board, and also a squeezed fit for the DHT11…
Rafts: No Supports: Yes Infill: 20%
This is a case for holding a NodeMCU v3 and 4x 7-segment MAX7219 8x8 led matrix. NOTE : The holes for the NodeMCU board are not properly aligned. The board fits but screws are a little angled. Will fix soon. Category: Electronics
Simple case for an ESP32-WROOM-32 (38-pin, 28x55mm) NodeMCU Dev board with NRF24L01+ antenna board. Prints without support. NRF24L01+ module stay in place once antenna has been screwed on. I used a bit of blu-tack to keep the ESP32 in…
Hi guys, this is a simple case for the Wemos D1 Mini (NodeMCU ESP8266) . Route the cables through the case bottom before you solder them to the Wemos D1 Mini. Easily resized and customized in Fusion360 with the provided .f3d file.…
a simple ESP8266 case Designed for use with WLED firmware Assembly instruction Print the case Solder power and data pin to the NodeMCU pull the cable through the hole in the back put the MCU board into the bottom part of the case put the…
Case / Enclosure for an ESP8266 / NodeMCU / ESP12-F Key Features: Accessible USB Port Prints without supports space for 3-5 wires no screws required, just click it together I'm using it for WLED Projects.
This is a case for the NodeMCU V3 - ESP8266 (e.g. for AZ-Delivery ESP8266 NodeMCU Lolin V3 ) esp8266_case_box v5 : added two holes to mount box with screws on a plate (e.g. with 2xM2). I hope you like the model! → Makes and Comments are…
Display box for 4xMAX7219 (Multi filamente + Single filament version) You can use PLA, PETG or others but of a light color (recommended white) , since the screen has 0.8mm of plastic in front that is used as a diffuser. MMU version…
The lid snaps in, just screws for mounting the electronics required
This is my remix of the Sensor Node Enclosure for ESP8266 by calvinboey on Thingiverse . I changed it in order to fit an ESP8266 and a BMP180, so I made it smaller and closed nearly all openings. Other sensors should also fit in the box,…
This is my rendition of a case with lid for the ESP32S NodeMCU board to house the DHT11 temperature and humidity sensor. This simple design ensures a tight fit for the ESP32S board, and also a squeezed fit for the DHT11 sensor. Also,…
This is an enclosure case for the NodeMCU V3 development board and base. ESP8266 Development Board NodeMCU V3 can be found here: https://www.amazon.com/dp/B07DK2LRJJ/?coliid=I37O15QSY8H0VA&colid=1PKM0NV2CRFRC&psc=1&ref_=lv_ov_lig_dp_it
Case for an ESP8266 NodeMCU with micro-usb connector. Press-fits together. If it is too lose, apply a drop of glue.
I've designed this case for the NodeMCU V3.2 Arduino ESP8266 (Lolin/Wemos), with a bit of space for a sensor. Print Settings Rafts: Doesn't Matter Supports: No Category: Electronics
Warning: You won't be able to access the Micro USB port with this enclosure! I modified this housing to be quite a bit slimmer, but it still has enough space for a level shifter and a 24V to 5V step down module. That's why the opening for…
This is a tiny box to hold a wide NodeMCU board. The box is tall enough that you can cram a few select parts underneath the board. There's a cutout for the (ugh) micro-USB port, and a hole to stick a 3mm LED out, or run some wires…
Remix of the Case from don frechdachs for Wemos D1 Mini (NodeMCU ESP8266) . I've added a cutout for the USB port. Compatible with the Wemos D1 Mini as seen here:…
Designed this case for my NodeMCU 1.0 ESP-12F ESP8266 board. Ordered a bunch of those from AliExpress (e.g. https://www.aliexpress.com/item/1005001621705950.html ) and needed a case to fit them. Case provides access at the front side to…
Case for a PIR sensor large enough to contain a nodemcu
Modified for esp8266(with no letters) NodeMCU PCB size is about 58mm X 31.1mm It fits quite tight. A bit hard to remove from the case.
Remixed techniczny's case to fit with my specific nodemcu and relay module nodemcu used: AZDelivery NodeMCU Lua Amica Modul V2 ESP8266 ESP-12F relay used: AZDelivery 2-relay module 5V with optocoupler low-level-trigger 3 versions uploaded…
Simple, well fitted enclosure for NodeMCU. Designed to fit Voron DIN rail clip. https://github.com/VoronDesign/Voron-2/blob/Voron2.4/STLs/Electronics_Bay/pcb_din_clip_x3.stl To assembly you need 4xm3x16mm screws, 4xm3 nuts, 2xm2x10mm self…
ESP-32 Dev Kit C NodeMCU - Cover for WiFi Repeater . Filament eSun PLA+ Black
This is my attempt at creating an enclosed box for the ESP Development Board 8266 for my LED projects. I wanted to house the board its self along with wago connectors that I have all in one place looking neat and tidy. Wagos are great,…
Simple Model of the ESP-32 NodeMCU Developmentboard by AZ-Delivery. Can be used to get Placement of the USB-Port right.
Simple case for an ESP8266 or ESP32 board (in my case NodeMCU), a temperature sensor DHT11 or DHT22 and a small SSD1306 oled screen. Works great as a small Duino-Coin IoT setup. Designed with Tinkercad. Parts need to be glued together…
A case design for NodeMcu V2, Amica This Design is base on the design from Crashoverride, published Jan 30, 2016 https://www.thingiverse.com/thing:1305796 Category: DIY
These are the enclosures I designed for the DIY-Sensor for a Ferraris wheel power counter with an Amica NodeMCU ESP8266. You can read details on the setup and build and get the software at…
imported from thingiverse. remix: https://www.thingiverse.com/thing:4515152 Enclosure for a NodeMCU v3 board with space for a connector to a strip of addressable LEDs. Powered via an external 5V USB power supply. Suitable for powering LED…
I made this case to house nodemcu with esp3d installed for my delta. There are two variants - w_2020_mount is intended to be mounted on 2020 profile. Screws needed are M2x6 Category: 3D Printer Accessories
Created an enclosure for the slightly larger NodeMCU, specifically this one: https://www.aliexpress.com/item/5PCS-V3-CH340-Wireless-module-NodeMcu-Lua-WIFI-Internet-of-Things-development-board-based-ESP8266-esp/32794607540.html My NodeMCU…
V2 - 04/11/21 I haven't printed this new version yet. Updates are: Added slit in the screw poles in the main body to add a nut, so it keeps the lid and body together much tighter without straining the plastic too much. Made walls slightly…
just added 15 mm of height
Simple and small NodeMCU(ESP8266) and DHT22 case. 4x bolt m3x12mm The DHT22 is very close to the ESP. Create a code to put the ESP in “Sleep”. Then it will work fine!
There are lots of project boxes out there. I needed a specific design that requires no screws. I hope you enjoy my little endeavor. It was a lot of fun to design and every time I design something I learn some new ideas on better design!…
A slim case for the ESP8266 NodeMcu V3 CH340 micro-USB micro controller boards I picked up on AliExpress NodeMcu-CH340-V3 . The style of this case is inspired by the Raspberry Pi Pico snap-together case by @glabifrons Designed for 0.2mm…
Made this enclosure for quick prototyping for CH340 Chip NodeMCUs. It has kinda snap to fit function but do not rely on that :) Hope it does help. Also attached step file so feel free to modify. Material eSun PLA+ Black Hotend Temp 215…
This is a case for an ESP8266 NodeMCU v3 from LoLin. This Case uses no screws. Everything fints in because of friction fit. It is made for Spacehuhn's espdeauther. All credits belongs to Spacehuhn!…
I've recently upgraded to an SKR Mini E3 V3 board and had an ESP8266 lying aound, so I decided to set up ESP3D and put it in a box attached to the middle extrusion. Features: Dupont connectors are accessible, but not exposed. The top is…
This is a bin für D1 Mini NodeMCU V3 which fits into the gridfinity system and is also stackable with other bins.
A case/cover/shell for NodeMCU (ESP-12E) For V2 CP2102
GrabCAD(Get The STP File): https://grabcad.com/library/esp8266-nodemcu-lua-case-1 Print Settings Printer: Ender 3 V2 Rafts: No Supports: No Resolution: 0.2 Infill: 100% Category: Gadgets
This case is for a NodeMCU ESP8226 V3 Lolin module. The lid is inserted under preassure. The model has 2 parts, the case and the lid.
Every time I build a little electronics project, I hate how the components usually just rattle around in the case. So I designed this customizeable solution in OpenSCAD that lets me configure the number of pins, the sizing and spacing,…
Simple case for NodeMcu v3 (LoLin). Inspired by the other cases, build from scratch. It has openings for the IO and the USB, as well as for the reset and flash buttons. Closes nice and tight - no need to add bolts or tape to keep it…
NodeMCU case with lid, DS18B20 doesn't contact with model.
Just another box to put your Nodemcu together with a Meanwell 15W 5V power supply :-)
Found this ESP8266 nodeMCU case and wanted to use it for my co2 level monitoring system at home. I added a build in housing for a SCD40 (same format as SCD41) co2/temperature/humidity sensor and a screwbase for easy wall mounting using…
a simple box to hold an Amica nodeMCU (v2) Category: Electronics
A case/cover/shell for NodeMCU (ESP-12E) For v3 CH340
This box was designed to contain a NodeMCU board and a breakout sensor boar. In my case I'm using a DS18b20 sensor to measure room temperature. There is a small space dedicated to the sensor to minimize the thermal effect due to the board…
A case for an ESP8266 NodeMCU V3 from AZdelivery with Relais. Category: Electronics
Battery holder for ESP-32 NodeMCU
This project contains a box to hide the nodeMCU esp8266 together with a 0.96" oled display. The box is then connected to an external usb power supply that is on the nodeMCU board. First, the nodeMCU board is slid into the bottom box on…
This is a case with a couple different options for a NodeMCU ESP8266MOD v3.2 by ideaspark with onboard .96 inch OLED display. For the small/thin version you will need M2.5x25mm bolts, washers and nuts. This version consists of the BASE,…
I loved the idea by warwound, but wanted some extra form factors. Here are 8 and 15 row breadboard modules as well as all combinations of 8/15 row controller and 8/15 row breadboard. I also found the metal clips from a donor breadboard to…
Lighthouse A fully modular, parametric, and customizable case design for home-made ESP8266/Arduino/Raspberry Pi projects, like temperature or motion sensors, information monitors, and more. Built with OpenSCAD. Source on GitHub:…
modified to fit the 38 pin ESP32 NodeMCU
Case to make a presence sensor with an ESP32 NodeMCU32s and an LD2450 mmWave sensor, the lid also has holes to glue 9x3mm neodymium magnets. The ESP32 and LD2450 should not require any glue and should stay in place once the lid is screwed…
This is a new version from scratch I made for the nodeMCU v3, that is bigger than the v2. In this version, I tried to put everything I needed in the same case, even a 4 pin connector, so you won't need and additional case to hold all the…
Basic protective box for NodeMcu Base Ver 1.0 Created with OpenScad and YAPP_Box . Scad file attached.
Dies ist ein Xbox one X Stand. Ich habe die ersten 8mm mit einem weißen Filament gedruckt um nur den Boden zu Beleuchten, wie viel ihr weiß druckt ist natürlich euch überlassen. In der Mitte ist Platz für eine NodeMCU V3 (Anschraubbar)…
This is a case for a NodeMCU ESP8266 with additional room for 3 other PCBs. I made this because I wanted to control my wireless Somfy IO roller blinds in Home Assistant. I connected an ESP8266 (NodeMCU) to the button pads on the PCB of…
Einfaches Gehäuse für eine NodeMCU mit Platz um Kabel ausführen zu können und seitlichem Kabelabgang mit Kabelbinder Befestigung. Simple housing for a NodeMCU with space to route cables and side cable outlet with cable tie attachment…
