Counting matching models…
Carefully set up your printer! Because 1/2 UNF thread will be printed. My settings are: Resolution 0.15 Perimeter 4 Without any supports Included 20mm Brim on the outside only I used Prusament PLA Simply Green . You can easily use other…
Print approx. €6.95–€8.49 excl. taxPreliminary estimate for one variant
I designed these for my mom after she lost one of her original ones. I used a ballistic chronograph to compare to the originals and was unable to see any difference in performance. Printing notes: The casing is printed in PETG, and the…
Print approx. €0.26–€0.32 excl. taxPreliminary estimate for PETGSource material: PET
This tripod foot is meant to be an improvement over the Losmandy Tripod Foot, which does not stay attached to the tripod during transit. This new design fits into the open bottom of the leg extrusion, friction fit, so that it stays with…
Print approx. €3.21–€3.93 excl. taxPreliminary estimate for PETGSource material: PET
Add a picatinny rail to the stock of your Crosman 1077 air rifle. This likely will only work on the synthetic (plastic) stock. Required: 3x m4 countersunk screws 3x m4 nuts Installation Instructions: Remove 3 screws from bottom of stock,…
Print approx. €1.60–€1.96 excl. taxPreliminary estimate for one variant
The 3D preview on this site shows the negative objects as part of the model, but don’t worry — the model is designed correctly 😄 The preview here is very approximate. I also added a screenshot showing how it looks after slicing/rendering…
Print approx. €0.34–€0.42 excl. taxPreliminary estimate for PETGSource material: PET
This is a cradle of the Losmandy Gemini II hand controller for the Berlebach planet tripod.
Print approx. €3.10–€3.79 excl. taxPreliminary estimate for PETGSource material: PET
This is a mounting plate for the GMKtec NucBox5 mini PC. The mini PC has two M2 screw holes on the bottom, which I use to attach the plate. The plate itself provides two positions for M4 hexagon nuts, allowing it to be mounted with the…
Print approx. €1.04–€1.27 excl. taxPreliminary estimate for one variant
This is a cover of RA transmission axes for the Losmandy G11T equatorial mount after changing the transmission method via pulley. Losmandy mounts are all well designed for easy service & maintenance. The original design between worm gear…
This is a 15x15x40mm bubble level holder for the RA axis of Losmandy GM8/G811 equatorial mounts.
Print approx. €1.40–€1.71 excl. taxPreliminary estimate for PETGSource material: PET
An airgun silencer, model supplied for 22 calibre, with an expansion chamber and K-type baffles that prints without support. Particularly useful for silencing CO2 and pneumatic airguns, designed for the Crosman 2250 “Ratcatcher.” Firearms…
I've been having fun using Shred-er mags with the Vigilante, but in my shop I'm frequently hunting insects larger than flies. A little more ‘oomph’ would be fun. Current versions: The V10 barrel and V8 cylinder are quite functional, well…
This piece is currently a work in progress as I have not finished printing it or tested it yet. NOTICE: This suppressor is intended only for use on BB guns / Air Rifles. This in no way is meant for production for or use on actual…
Silencer for the Crosman 1077. 105db without supressor, 80,1db with supressor. Neighbourfrindly ;-) I print it with 60% infill. I print it with ABS, but i think PLA is also working. Thx to Sidenius and BlixFox! Category: Sport & Outdoors
This made an incredible difference on my 2240. Now you can hear the hammer when firing. I haven't noticed any negatives on accuracy and the FPS is unaffected. If it does not fit snuggly enough, use glue ;) Make sure you get clean…
This losmandy-style dovetail is intended to be mounted on top of a telescope for accessories like minipcs, dew heater controllers and power-distro. All threaded holes are M6x1 threading. This bar is intended ONLY for top mount use, do not…
The hole pattern is 4xM4 20 mm cross. Matches the hole pattern on the bottom of the ASIAIR. Instead of mounting the air straight to the mount, you can mount the saddle and shoe the ASIAIR comes with. You'll need one M4x20 screw and nut…
This is the same as this, but with two added rails; https://www.printables.com/model/326303-crosman-2240-picatinny-for-bipod-or-laser CAD file included
Crosman Vigilante Pellet Clip This clip works the same as the OEM pellet clip and the bug-a-salt clip. Print Settings Printer: Bambu Labs X1C Rafts: No Supports: No Resolution: 0.2 Infill: 35 Filament: Overture PETG Black Notes: Printed…
I created this Losmandy style camp, so I can attach whatever I like on my OTA. I found some others on the internet, that did not clamp enough or used imperial sizes. This is a remix clamping better for me and using regular nuts and bolts.…
I love Crosman 1377 / 1322 Silencer Adaptor by k19k19 , but I printed it and adjusted the design multiple times and just couldn't get a model strong enough or that would print cleanly and nicely enough. So I remade it from scratch with…
Many of the designs on here for mounting a rail on the 1377 are rather imperfect, rely on disassembly of the pistol, have model errors, are low resolution, or incorrect dimensions. This solves the issue for me. I wanted a screwless, low…
A remix of Crosman 1377 suppressor V2. The original was a 5mm hole for 4.5mm (.177) pellet. This has a 7mm hole for 5.6mm (.22) pellet. I also made this a two piece threaded design. This makes managing supports simpler. Also, if you break…
The foosball crew at work broke one of the foosemen on our Tornado table. Since I'm known as the guy who can get things done, they asked me to make a replacement. I used the one they broke to make this model, mine has a hat brim and an…
Use 2 M3x5 set screws to fasten. Includes two versions, one with the NEMESIS text as on picture and one with no text
Use two M3x10 Caphead screws and two nyloc nuts I had problems printing this with Arachne enabled and my 0.4 nozzle, the perimeters didn't fuse, so I had to use classic perimeter generator.
I wanted a decent scope on my Crosman 2250b Ratcatcher so made this. It holds in place on with the force of the scope clamp being tightened and I've had no issue with mine for years.
Print Settings Printer brand: Creality Printer: Ender 3 Rafts: Yes Supports: No Resolution: 0,2mm layer hight; 0,4 nozzle Infill: 15% Filament brand: FilamentPM Filament color: black Filament material: PETG Notes: 1x: body 1x: riser 2x:…
This part is a remix of Erwin's Losmandy Clamp, slightly modified to provide a tighter fit for Celestron CGE dovetails. A printable knob is included to make mounting the clamp easier. The larger part in the print is unmodified, so if you…
This set of radius block allows you to attach a narrow dovetail bar (i.e. Vixen / CG-5) to the Losmandy attachment points on a Celestron C8. This is useful when you wish to (1) attach your C8 to your mount using a Vixen bar, AND (2)…
Remixed from the two files. Took the front sight post off the original design and added it to the improved barrel band for the 1322. I do not run an optic on my 1322. I painted it white. Grab the silencer from the original 1322 Thing.…
Crosman 1077 Reloading station Fits two magazines “Clips” Storage for 1077 Clips Tool https://www.printables.com/model/527527-crosman-1077-clips-tool Dimensions: X 66mm Y 55mm Z 10mm My print settings: Layer Height: 0,2 Perimeters: 3…
Mk.3 revision posted now! Strengthening rib minimized to be easily removed if desired; removable support built into the main lug. My recommendation is to grind out a bit of the pump arm to clear the rib and keep the part stronger. The…
Cut down from the Mk.2 buttstock and given just a bit of palm swell. Will help stabilize aim with one or both hands and compliments the accompanying Pump Arm fairly well. This is an ambidextrous model, though one may forego or install the…
I designed a replacement handle for the Crosman 1322 and 1377 pellet airgun. It has a picatinny rail on the left side that supports a flashlight or laser. It's nice for larger hands and feels more sturdy than the standard handle. Note…
2/12/25 Update - Check out my new Crosman 2100B moderator mount. Print as many baffles as you want; the more baffles, the greater the sound suppression. Make sure to print one endcap. The barrel adapter is designed to be secured with a…
Print it standing up, NOT as I did in my picture, that was just me being lazy so I could post a picture of it printed. -Stupid I know ;) Hardware needed: M3X3 Set screw - 2PCS
Single side and triple picatinny mount for Crosman 1322 and 2240.
Printed with PETG with supports on the bottom. I put a ventilation slot on the bottom.
What this is: Makes crosman stock longer so you dont have to bent to it if you are a little bit larger like me. You can also make it even longer by adding spacers between stages 1 and 2. Butt stock is also adjustable in height so you can…
I let the gasket for the CO2 cartridge on my Crosman 357 pellet gun dry out to the point that it would not hold pressure when a new cartridge was punctured. I was able to remove the old gasket and take some measurements and this printed…
Losmandy rail clamp that is designed to mount a lightweight object, such as a mini pc to a Losmandy/"D" rail installed on a telescope. Unless the 4 M3 screws match up directly (30mm on center) with your piece of equipment/object, you will…
A modified rear sight to fit the Crosman steel breech using the factory steel sight blade insert and screw. I extended it to the rear to clear the plug on the steel breech, and made it to sit flush on top of the dove tail using a printed…
This is a 2" wide losmandy rail clamp that was designed to hold a lightweight object on the top rail mounted on a telescope. The round hole in the flat portion of the clamp is for a 1/4-20 screw that is counter-bore (.44" wide X .30"…
I love the original Crosman Pump Arm with Wide Grip by Gecko23 but it would not fit my Crosman 1377, I guess Crosman changed the design at some point. Maybe that applies to the 1322 as we. I made some changes to the original design to…
This project is a slight refinement on the Thingiverse project: https://www.thingiverse.com/thing:2881213 I designed this to have tighter tolerances, and be a little more resistant to breakage. This is a completely customizable (made in…
I liked the Moderator/Muzzle break from Dan , but the threads would snap off anytime I would pump my Crosman 2100B air rifle, so instead of just relying on the threaded part to hold a moderator on, I added a shrouded portion to snugly…
Crosman 1077 Barrel Stabilizer Fits Powermaster 66 as well Might fit other Crosman models? 1077 inner barrel outer diameter 7,93mm "5/16" 0,3125 inch Item Dimensions: X 14.1mm Y 14.1mm Z 30mm Use Silicone grease on the contact area with…
Remix of a Losmandy clamp model from Onshape by Alex Douglas. I see a lot of variations of it floating around, not sure who the originator is. This model passed fit checks, clamps well, and worked flawlessly for its first night of use.…
This is a stiffening liner for the current narrow Crosman 13xx/Drifter forend. It completely fills the hollow space between the forend shell, the metal lever, and the air tube. Helps eliminate that toy-like feel when pumping and holding…
Shoulder stock for Benjamin Trail NP Mark II .177 caliber air pistol. Could not find anything serious online for this break action/nitro piston, air pistol, so I decided to create my own mod. For this mod you will need 20mm Carbon Fiber…
Thickened up a bit for strength and minor changes to print easier. Printed with the rail side down Sanding the bottom on a round dowel is highly recommended to get a good solid mount the lower bolt guide is removable for those without…
Crosman 1077 Clips Tool, Seating pellets flush Ejecting stuck/bad pellets Crosman 1077 Reload Tray https://www.printables.com/model/535789-crosman-1077-reload-tray My print settings: Layer Height: 0,2 Perimeters: 3 Solid Layers: 3 Infill:…
Trying to balance utility and width, this improved furniture is designed to clear its full sweep even with one of my standard or extended suppressors attached. Well-complimented by these improved grips . Though most factory units are…
With interchangeable plates and grips for all your hexagon needs, this stock has a relatively tight length-of-pull and is tall enough for good scope alignment. Bed the top with some flexible adhesive or RTV to reduce vibration/noise from…
This is a first draft customizable picatinny rail for the Crosman P1322 pellet gun. All the parameters are customizable -- see the included OpenSCAD file. So this should be readily adaptable to any similarly configured pellet gun. The…
2/12/25 Update - Check out my new Crosman 2100B moderator mount. I remixed the barrel adapter and added ½"-20 threads to allow the use of any threaded moderator you might have or want to print. The barrel adapter is designed to be secured…
Picatinny rail for a vintage 1965 Crosman 760 Pumpmaster. Mounts to the barrel using the iron sight screws as well as clamping to the barrel using M3x16mm machine screws. Printed with Elegoo PLA, brim, 90% infill. Chased through holes…
As it has no affect to the function I simply cut the sides of the figure, so the model uses very few to no support. I used support only under the “legs”. I used 5 perimeters and 20% infill for a really stron and sturdy foosman.
Trying to balance utility and width, this improved furniture is designed to clear its full sweep even with one of my standard or extended suppressors attached. Though most factory units are attached with roll pins, this model has recesses…
Requires 2x or 4x M5x12 bolts and nuts. A variation of mounts included. I recommend double screw mounts, over single screw. You'll probably want to make a mirrored copy of your chosen fine in your slicer (Press M in Cura). I've provided a…
After pinching my palm for the last time pumping up my 1377, I went looking for an easier to grip option. I considered a wooden grip, but I wanted to keep the cost lower. At some point in my wandering I acquired a model of a Crosman Pump…
There are two files, one for the actual TPU seal and the other for converting an 11/32 ¼" hex socket into a removal tool. The printed insert is just a guide - it is very difficult to do without it. FreeCAD files are included so you can…
Well, I bought a used OTA without really looking at the dovetail style until two days before I planned to use it. I couldn't find anything at a reasonable price, let alone anything that would arrive in time. So I decided to design an…
Adaptor to fit an old style 1377 stock to new style Crosman air pistols. Was given an old 1377, the stock does not fit a new Crosman 1377, due to major design changes. Through a lot of trial and error, got a solution to fit it. Pretty…
Fits tightly around the barrel of a Crosman 2240. Keeps it stable so you can dial in your sights.
You must add a sleeve and cap to contain the telescoped baffle core. Final baffle is tight and will need touchup with a drill, especially if used for .20 or .22 caliber pellets. This is probably best as a learning tool and experimental…
Durch diverse Umbauten war meine Endkappe etwas lädiert, auf MakerWorld fand ich eine mit Picatinny Slots aber die Stabilität war nicht sehr gut, die Schrauben hielten nicht gut im Material, so entschied ich mich 2 Phasen für M3 Muttern…
Measured up a rear sight to be able to make a custom version of it. Here is the model. Should be pretty much 1:1 with real dimensions. Print Settings Printer Brand: Creality Printer: Ender-3 v2 Rafts: No Supports: No Resolution: 0.12mm…
Crosman Front Sight Remover Tool With this tool the front sight can be reused and takes no damage during the removal process. Use light taps with a hammer on this tool. Use tape to keep it in place with the sight. One hand on the Air…
These are two different designs that are meant to go over the standard knobs used on Losmandy telescope mounts (i.e. G11, G8, etc.) in order to help with comfort and leverage, particularly during loosening. Especially during the winter…
need to be print on the side for more solidity or it gonna brake open de side off the revolver and slide it inside with the screw already in
Because Darkknight24 asked in the cosplay group, I did a 3D model of the Osmanian Order of Osmanieh as a 3D Model. It needs to be printed with support. It also needs to be painted - the inscription can't be printed. However, for easier…
I introduce the Askar Universal Losmandy-Style Dovetail Full Plate Series. 200mm Completed 300mm Completed 400mm Completed 500mm (In Progress...if I can find a reliable diagram...) I have added a line of holes every 10mm on the dovetail…
This is a collection of replacement rear sight blades for the Crosman 13XX/22XX series of airguns. They directly replace part OS244. These are designed to fit very snugly into AlanMoulding's Steel Breech Rear Sight. Depending on the…
Base geometry of William Osman's wall hole including cutouts for rocker switches and mounting holes. Sized in mm. I cannot guarantee compatibility but it's probably close. Even if it doesn't fit, you'll be wrong along with everyone else.…
This dovetail converter will enable you to convert your Losmandy plates to accept Vixen-style. << BOM >> m5 hex bolt 40mm 2ea m5 hex sockethead cap screw 20mm 8ea m5 hexagon nut 10ea Instant adhesive
Grip-nut CELESTRON CGX CGXL losmandy nut
I could have used bolts to achieve the same function but metal bolts would mar the finish of my telescope mount. So I designed a plastic brake to prevent the telescope from sliding off the mount if the mount clamps are not tight enough.…
I was hosting a Foosball Tournament at my company, and I wanted to print a foosman for the trophies, but I had difficulties with the support generated by Ultimaker S5 from the original piece because the support was too strong, making…
Had lost / broken the little loader door on my Crosman 760 some time ago. Decided to make my own and it worked really well so figured I'd upload in case anyone else was in need. I printed mine on 0.15mm Quality and used full supports and…
Covers that flat spot left when the rear sight is removed to install a scope or other optics. Options are for a pan head or flat head screw. A shorter screw will be needed, 8/32 x ¾" Also included with the barrel adapters for my…
Crosse Crosman Benjamin ARMADA
Front sight for the Crosman C1K77
UPDATE Over the past few days, I've been working on this design and made some changes. There are now stepper mounts for both RA and DEC, and a single belt cover design that fits both stepper mounts. In addition, on the inside of the…
I needed a Losmandy clamp for an 8" SCT Dovetail bar to hold an AISAIR plus and/or guide scope. Every model I found required an intermediary between two styles of clamps (perhaps I could've searched deeper, I have an unusual set-up, or I…
Adapter plate to attach a Morefine M6 MiniPC to this Losmandy/"D" rail clamp . Used together, this mounts on a Losmandy rail installed on a telescope. The 4 inset mounting holes are for M3 hex nuts and are 30mm on center. The 2 adapter…
I remixed the clamp and added holes for mounting Pegasus Astro gear. M3x16mm Screws, a M6 screw and a M6 nut needed. I printed it with the Prusa Mk2S and PLA.
Da ich meine Crosman 1377, mal mit nem RedDot und mal mit nem ZF schieße, habe ich mir eine Picatinny Schiene auf voller Länge konstruiert. Da meine 1377 einen Schalldämpfer Adapter hat, weiß ich nicht ob die Schiene auf bei Waffen ohne…
Drummer's neck tattoo symbol as a coaster, with the font from the Expanse saying “Bosmang”. Drummer is 100% the bosmang! Sasa ke? Printed in 2 levels, black then light color (I use silver). Enjoy.
Youtuber William Osman bought himself a used Bobcat337 that was missing the handles for the driving levers. Not having faith in his own CAD skills he asked his viewers to design and send him some. “Don't do anything weird though.” Knowing…
30° Meridian Offset Wedge 3D Printable wedge designed to provide an additional 30 degrees of offset to allow imaging across the meridian line in RA mode without meridian flip. This was originally developed in response to discovering that…
Moderator and shroud spacer for your crosman crusher .22 use 50% infill and I would use at minimum PLA+, results will very. You don't want to grab this while cocking your rifle, was not designed to handle this type of force and will…
There are 2 models, each with 6.5 mm holes, one with a 1 inch separation and another with a 1.5 inch separation and a bit more height to handle 2 cables and 3 cables respectively held down on a Losmandy Universal Dovetail Plate.
When I first got my 1322 I loved it, but as a leftie the safety wasnt very comfortable. I looked to buy a replacement but its $25-30 for one from china, so instead I made one myself. Ive been using it for months now with zero issues, just…
Based on the diagram provided by @HarrisonWils_2000543 Built in Tinkercad, I spaced out the hole placement based on the drawing, then just made the plate bigger, super basic. This is just reference in case anyone wants to use it, or test…
Here is an .STL I modeled while creating Excavator Knobs as per William Osman's request. Use this to do a boolean IE use as a negative model to cutout whatever knob you like. Added .45mm to X&Y for fitment. Here's the video for reference.
This is a cover of DEC transmission axes for the Losmandy G11T equatorial mount after changing the transmission method via pulley. Losmandy mounts are all well designed for easy service & maintenance. The original design between worm gear…
I decided to use a Crosman Voodoo shotgun for indoor airsoft, but I wanted a tracer unit to attach. I therefore made this adapter that push fits over the orange end cap, inside the outer barrel and over the inner barrel. The fitment is…
