174 models
After using the zip ties for a while to level the Pinda Probe I started to get worried about running out of them so I designed this. This replaces the zip tie that is used to level the probe. It is a very quick print and is well worth…
Useful for finding the right distance of the Super PINDA from the print bed. The optimal distance for the Super PINDA is about 1.5mm. That should get your optimal Live Z/first layer calibration to somewhere around -1.00, so you'll have…
Searching for a better fan duct, i found this this (thx to xander1) https://www.thingiverse.com/thing:4124587 The initial tests weren't bad, but the airflow didn't fully reach the rear of the model. So I copied the design and gave it a…
Last night I had to readjust the Super PINDA on one of my printers. I found a bunch of height gauges for the old PINDA/MINDA on prusaprinters.org, with a height of 1-1.2 mm: https://www.prusaprinters.org/prints/27679…
Prusa empfiehlt die PINDA mit einer Kreditkarte einzustellen, was mir nicht so gefällt, da man mit der Düse an das Druckbrett fahren muss und diesen beschädigen könnte. warten bis gereinigte Düse abgekühlt ist. Drucker ausschalten.…
Just a simple tool to set the correct height of the Pinda or Minda probe. Yes i know this is also the thickness or a simple calbe-tie! But i ran out of those so this little print came to the rescue. Print instructions Just print at 0.2 mm…
PLA works well, though higher temp materials will likely last longer if scraping while bed is hot. 40x180x9mm 1mm PINDA tool depth Rev 1: Slightly reworked geometry for strength and reduced overhang angle
Introducing the SuperPINDA Precision Adjuster! The SuperPINDA Precision Adjuster (SPA) is an integrated mount and adjustment tool for the SuperPINDA probe. This first version is specific to the Prusa i3 MK3S+, however the Drill Bit…
It helps you offset pinda and nozzle far easier than paper and ziptie method. Note: It is for newer S Pinda 1.5mm only. For 0.8 older version, you could open freecad file and decrease pad from 1.5mm to 0.8mm, then export stl file. Steps:…
I wanted to reusing the PINDA probe (from my MKS 2.5S) in a voron-styled x-carriage remake. This allows you to mount the PINDA just like the other probe normally used in a Voron 2.4/Trident/etc. In my case, I'm using it to compliment the…
Simple 1mm shim to correctly position the PINDA probe much more practical cable tie Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: prusament PETG orange Category: 3D…
I printed the original height adjustment tool which is awesome since it is a consistent reference to set the SPINDA height to, and also because it stows out of the way right on the printer frame after use. However, I have a Bondtech LGX…
D.R.O.P.P.E.R. Durable Rapid Object for Painless P.I.N.D.A. Easy Re-Positioning Simply drop your P.I.N.D.A. down onto this tool for the perfect (?) P.I.N.D.A. position. To be honest I don't know if it's the perfect P.I.N.D.A. position,…
This is a remixed version of the Bear Extruder 0.7.0-beta ( https://www.thingiverse.com/thing:3716110 ) with the intent to allow the use of a standalone BMG extruder within the frame of the original extruder body. Compatible with…
With this JIG you can calibrate the height of your SuperPINDA probe everytime you need to calibrate it. It is 1mm height, between the recommended height for the superpinda probe.
The same great SuperPINDA Precision Adjuster for the MK3S+ , now available for your MINI/MINI+! The SuperPINDA Precision Adjuster (SPA) is an integrated mount and adjustment tool for the SuperPINDA probe on your MINI/MINI+. Overview: The…
SUPER PINDA 1.5mm adjustment tool 1.5mm height adjustment tool to easy calibrate your SUPER P.I.N.D.A of your Prusa Mk3S+ / Mini+. Only 10 minutes to print. No support needed. Keep in mind : Always recalibrate the Z-live after a Super…
I needed a way to mount the Stealthburner with an original Bondtech LGX to my CR10 S5. I found this Afterburner adapter on thingiverse and remixed it to fit my needs ( https://www.thingiverse.com/thing:4638150 ). The LGX adapter came from…
Dragon Burner remix for 8 mm diameter inductive probe, tighten the probe with M3 screw. OnShape: https://cad.onshape.com/documents/e60d6bbb7afa598d50a74769 Offsets (from OnShape): X: +31.300 mm Y: -17.418 mm
Hides away by snapping directly into any 3030 channel, on both the Mini and MK3 series. Useful if you do frequent nozzle swaps. Tested and working, good offset for the distance for first layer calibration for the SuperPINDA specifically,…
Make sure you have the correct distance between the bed and the PINDA. Tool to use when adjusting. According to PRUSA KB distance should be between 0.8-1.0 mm. This tool measures 0.9. Follow the official Prusa guidelines and use this…
I created a mount for the pinda probe to fit the Voron-style head as I didn't find a mount I liked. The provided gcode is for PETG, but the Voron team recommends it to be printed in something rated for higher temperatures. Brass inserts…
Spatula 3in1 - Spatula, SuperPINDA adjust tool and Prusa Allen keys keeper. I used a credit card (0.80mm) as the right measure as we see the instructions at:…
This is partly a remix of the original Prusa parts, and a new part. Since I occasionally had warping with large area prints, I optimized the printer so that the air did not blow onto the print bed through the hotend. Since I am operating…
remodeled to make faster to print Print instructions No supports. Just print
SUPER PINDA 1.5mm adjustment with 3030 MOUNT 1.5mm height adjustment tool to easy calibrate your SUPER P.I.N.D.A of your Prusa Mk3S+ / Mini+. Hold it on the 3030 extruded frame or enclosure with its mount included. Only 20 minutes to…
Remix of ted.gaunts version. Modified M8 Superpinda holder to clamp with an M3x12 SHCS and Heatset Insert, reduce mounting hole size for using of an M8 Inductive Probe like Superpinda. printed in eSun ABS+, 0.2mm Layerheight 0.4mm Nozzle…
Mounting Bracket. Auto Level Probe Mount. Bobblejot Website Bobblejot GitHub Bobblejot Twitter Bobblejot Patreon Just a very simple mount with a threaded M8x1 through hole to mount M8 Inductive probes or the Prusa PINDA sensor. I have…
I modified this excellent improved part cooling duct with a notch on the RH side, like the original MK3S+ duct has, so it should be a direct replacement.
This is a REMIX of the excellent cable management adapter by clivebradshaw & enganear. Their versions didn't fit my Prusa Mini the way that I would have liked it to, so I decided to do some modifications to their design to fit my printer.…
This is a compact, neat, and fully Prusa style hotend for the Ender 3. Works best with a linear rail, and a Printermods direct drive plate. This should also work on the X-change system, and standard V wheel carriage. Changes from the…
PINDA 0.8mm adjustment 0.8mm height adjustment tool to easy calibrate your P.I.N.D.A of your Prusa Mk3S / Mk3 / Mk2.5S / Mk2.5 / Mini. Only 10 minutes to print. No support needed. Keep in mind : Always recalibrate the Z-live after a…
I was looking for something smaller for mounting the superpinda. Lower screw threads into the plastic. If you use a longer screw it can steer on the lower hole of the fan.
I printed the original which works really well (and simple but effective storage) but on the Prusa Mini+, it gives a Z height of around -1.400 on Satin. I remixed this to 2mm as quite a few forums posts recommend, which gives me…
Replacement PINDA sensor holder, in case you broke yours and need a replacement! Uses the original screw, fits in the original place (in my case I didn't need to modify anything further). Happy Printing!
This model proposes a unique tool that combines a 4x SuperPinda adjustment tool and a motor visualizer to attach to the X-Axis Extruder of your 3D printer. It will always be on hand whenever you need to adjust the SuperPINDA. You can…
This is a simple tool I created to accurately set my PINDA probe on my MK2.5S and MK3S. It's easier to use and more repeatable than a zip-tie. Print instructions Print out of PLA .4 Nozzle 30% infill
advise printing in abs due to its proximity to hotend
With this simple adapter, the original Prusa SuperPINDA sensor can be used in the Sovol SV06. For the SuperPINDA sensor you don't need any software adjustments, neither in Marlin nor in Klipper, it is electronically compatible to the…
Needs support for print, additional screw (from the spares bag) and a normal nut is needed, on top on the design it's based on. The model in Tinkercad: https://www.tinkercad.com/things/jr888EBxI6w
Just a simple block that allows the quick adjustment of a Pinda/Minda sensor to 1mm from nozzle tip. No zip tie needed and you don't need to run the Z all the way to the bed. Place vertically on heat bed and run Z down to where the nozzle…
A cover for Prusa MK3/MK3S PINDA probe. Video: https://youtu.be/WsIvEf7D54I Print instructions Filament: Prusa PETG Colour: Orange (depends your favorite) Fill: 100% Support: No Filament temperature: 225 - 230 Bed temperature: 85-90
This is a modified pinda holder for the Prusa Mini. It shifts the position forward 5.6mm and is meant to be an addon for Miko's modified electronics box which shifts the gantry 5.6mm further backwards. This is all so you can install the…
This is the Cowling for the Mini Stealthburner on a Voron 0.1 or 0.2 with an added slot for the PINDA sensor. So you can enable probing on the Voron0 >> You will not loose any print area, as the pinda sensor is now located on the back…
To adapt our BIQU Hurakan to use H2 V2S REVO we need to adapt SuperPinda/Pinda 8mm sensor for all H2 extruders series. Klipper configuration changes: [probe] ... x_offset: 5 # Original 0.0 y_offset: -17.8 # Original -30 ... [safe_z_home]…
I just don't like the pinda v2 light grey cap, so I remix to it. Video: https://youtu.be/wPyIDwtcffA
The proposed modification to replace the ABL sensor with an inductive sensor makes sense if the printer is equipped with a metal PEI board. Additional comments. The PRUSA SUPERPINDA sensor has a standard deviation of less than 0.005. The…
MINI-X-Carriage_SUPERPINDA Holder -lightweight version for print without support. Printed in PETG.
This is an adapter to use a PINDA probe instead of a BLTouch, while keeping the initial mount for the BLTouch. Basically mimics a BLTouch body and clamps a PINDA in the middle. LJ8 type probes won't work because they are too long, a PINDA…
To have all top surfaces of the model be at their intended height, you must either use 0.1mm layers everywhere (except 1st layer), or you can use 0.3mm layers with thin layers only where needed to get the correct top layer heights. Using…
The probe is mounted 35mm to the right of the nozzle and 3.1mm behind. The models are oriented correctly. The pinda mount requires a square M3 nut (Prusa style) and an M3x12mm screw. Brass inserts are needed to mount the printhead. I used…
Not my design, but from whoever design for the MK2. I basically redraw the thread and the hole from the original one from the official site since I cannot get it to fit nicely on the PINDA probe if I print it with PETG. Anyway, I just…
This model is a remix of other designs available on Printables. I changed the model so it is now in 2 parts that are bolted together. I had problems with other designs that would break when screwing down the holder. This design requires 2…
I made this model because I couldn't find any suitable one. pinda sensor is attached on the right side so that the left adxl remains free. The mount is for the stealthburner printhead version revo-V6 part. Insert the threaded insert into…
The official Prusa model of the MK3S extruder body (version R5) but the part that holds pinda has 3 perimeters and 40% infill. This thing often cracked for me when I was tightening PINDA, thus some more perimeters around PINDA should be…
Satsana Duct 5015/4010 with support to BLTouch and Pinda inductive probes remix This is a remix of the amazing Satsana Ender 3 Fan Duct by eric-anastas and max_davis's remix to support the BLTouch probe. Main enhancements of my remix:…
When using a Mellow V6 Pro adapter ( https://www.aliexpress.us/item/3256804525082538.html ), the tip of the nozzle goes even lower than with the Rapido UHF configuration. The original EVA3 probe mount barely catches the probe in the…
Original part was making a lot of strain on hotend cables. So I modified it to allow more space for cables I recommend printing it in ABS/ASA/PETG etc. 100% infill, 3 perimeters, 0.15mm layer.
PINDA 0.8mm adjustment with 3030 mount 0.8mm height adjustment tool to easy calibrate your P.I.N.D.A of your Prusa Mk3S / Mk3 / Mk2.5S / Mk2.5 / Mini. Hold it on the 3030 extruded frame or enclosure with its mount included. Only 20…
Rather than using a wire-tie, print this set of test strips to calibrate the height of your PINDA sensor on the i3MK3S+ or similar. If you're following the manual, start with the 1mm strip instead of the wire tie. Place your nozzle so…
Modified Printhead for the Voron 0.1 It is based on the Mini Afterburner with Orbiter 2.0 as Extruder and has a slot for the SuperPINDA probe. The probe ensures a perfect first layer :) Drawback is the reduced printvolume due to the PINDA…
This is a mount for the superpinda/8mm probe for the VZ Printhead cnc for RatRig that is mounted on the bottom left holes of the VZ cnc printhead. It has similar position as the original Eva probe but for accurate configuration please…
This is a remix of the thing:4894561. Gave a little more space for the duct for stock carriage. Don't forget to give Mr https://www.thingiverse.com/BoothyBoothy a thumbs up and check out his other awesome creations. This fits nicely with…
Update : Changed the size of the PINDA area so it fits better, there should be less chance of breakage. I wasn't happy with the stock inductive probe on my SV06+, so I bought an extra SuperPINDA and made this lightweight mount to cut down…
This is a remix of Original Prusa “MINI-minda-holder” by https://github.com/prusa3d . The left side is the same but on the right side the hole for the screw that attaches to the hotend fan is lowered by 2 millimeters. You can use this to…
couldnt find a pinda mount for the kp3s. designed this in onshape. works real well and mounts in the same manner as the bl touch mount for this. pinda works well on stock v1.3 or any other board with klipper printed in PLA 0.2mm 25%…
pinda probe mount. 8mm x_offset: 26 y_offset: 48
KP3S V6 (Super) PINDA inductive probe ABL sensor mount for this toolhead/printhead/fan shroud mod: https://www.printables.com/model/382202-kingroon-kp3s-30pro-mod-for-e3d-v6-bambu-lab-hoten Offsets: X: -22.5 mm Y: 0 OnShape:…
Print details Layer height: 0.2mm Infill: 10-20% Supports: No Materials: ABS Non-printable parts M3 threaded insert (x2) M3x6 BHCS (x2) PINDA probe (x1) Post processing Assemble the printhead as usual Fully thread the probe in the PINDA…
Recently I had an issue with my X-axis that involved a lot of disassembly and re-assembly and re-calibration runs. Never fun but sometimes necessary. One of the things that has bothered me is that the first layer cal was so dependent on…
Mount For The Pinda 2 Inductive Sensor To Go Onto The Ender 3 V2 Or Ender 3
I really liked Mavericks design for the Mini SB but wanted to add a PINDA. So here it is.
v2 Update - The hole for the probe is a bit wider so it does not have to be drilled at all, also trimmed it up a bit more to lower print time. I was able to use the existing top bolt by using a non nylock nut, but i may update it again to…
To be mounted in place of ADXL345 (as I use my own on-nozzle mount for input shaper calibration anyway - see https://www.printables.com/model/582444-adxl345-nozzle-mount :) OnShape:…
I was not happy with the other SuperPinda adapter on here so I designed my own. I made it threaded so the set screw can hold it in properly. I also designed it with a slot the full length making installing the SuperPinda extremely simple.…
i just remixed fukumay design from thingiverse it seem he doesnt have printa https://www.thingiverse.com/fukumay/designs
While ABD is not strictly necessary on V0, I had a Pinda around and decided to go for it. The design is based on the MiniAftersherpa (https://github.com/PrintersForAnts/Mini-AfterSherpa). The model has to be printed using supports for the…
it is a fun toy that you catch the ball in one end and the ball goes flying out the other and then you have to catch it again.
First of all thanks to @KalleKnall for providing the step files. This is the fan duct design that aims to fix airflow to the back of the model and improve overhangs. It also has PINDA support to prevent sagging. My favorite fan duct…
I upgraded my Sermoon D1 to PEI and find the Super Pinda to be the best probe for bed leveling, so I constructed this adapter. 6 M3x10 screws and 4x HEX Nut M3 are required. Printing without support is at least in PETG. The X offset is…
Lighter and more compact holder and in one peace.
Mount for a PINDA or other M8 sensor. Uses one of the stock hotend shroud bolt holes so this will NOT be compatible with a stock Ender 3 . I designed this for use with Bosco Lau 's Ender 3 Magnetic Hotend which doesn't use this screw…
This is v2 of my previous REMIX of the excellent cable management adapter by clivebradshaw & enganear. Their versions didn't fit my Prusa Mini the way that I would have liked it to, so I decided to do some modifications to their design to…
I create a remix from https://www.printables.com/es/model/35611-prusa-i3-mk3s-hemera-upgrade-30 beacuse i have a Hemera Revo XS and the motor is smaller than the normal Hemera. i update the file with a new model because the old have…
I made this part as an addition to my Ender 3 mainboard relocation kit, available on my Patreon. I thought I might add it here too if anyone needs it. Here are a few pictures of the Ender 3 mainboard relocation kit I created, if you want…
Added hole for Endstop mount (PINDA Probe) https://youtu.be/pV\_1MMs1W3E on the idler drum you need to insert a metal in the second hole from the left. on the picture it looks like its the third, but the first i drilled for tests. i…
It holds sensor and wires give more place for fitting change.
This is the tool and the process to adjust the PINDA probe position on Prusa i3 printers. The standard PINDA calibration process provided by Prusa is https://help.prusa3d.com/guide/9-preflight-check_95128 The inconvenience with Prusa…
Its just a simple holder to replace the capacitive sensor to a PINDA v2 :)
An adjustable PINDA mount for the Revo Prusa Mini to enable non-planar printing on your Revo Prusa Mini. Additional non-printed parts: x2 M3 square nuts x1 M3 x 8mm screw x1 M3 x 30mm screw
I made a PINDA protector cap that fits the MK2S extruder mount to prevent badly warped parts to get stuck on it while printing. Edit 28/10 2017: Since some people had problems with fitting the original model with the m8 threads I made one…
I like the height adjustment tool. I only have Bears now so I remixed this to fit in a 2020 profile. Not the tightest fit because I'm lazy.
I had a mixing hotend with a 3010 fan, seemed like a convenient place to mount the probe.
Remix of Sovol SV06 Plus inductive probe bracket to fit a PINDA probe and stock nozzle.
This is a modified Prusa MK3 extruder body, designed to accommodate a Z Probe with a 12mm barrel, rather than the 8mm barrel of the official Prusa PINDA probe. Specifically, it's meant for use with the Taiss 2pcs LJ12A3-4-Z/AX Inductive…
I didn't like how the original part looked and that it required a screw and nut, so I came up with this. Without cutting the threads first you might not be able to properly install or adjust the probe. I did this to have enough friction…
you can connect any pinda size abl sensor. stays on the front, outside of hotend cover.
A simple mount for Pinda (or other) induction probes utilizing stock CRTouch holes on the Ender 3 Y-axis gantry. Parts needed: 3 x m3*8 (or longer, up to cca m3*12) hex screws 1 x m3 hex nut You then may wire the probe into the dedicated…
