Counting matching models…
Printing: There are no special printing requirements, NO supports . For example 0,05mm layerheight, 2 perimeters, 100% infill. print max 3-4 layers.
If you need reading glasses you might have trouble seeing a sharp image on FPV goggles. With this clip you can attach lenses from inexpensive workshop magnifying glass like these (I couldn't find a place to buy just the lenses). Be sure…
I started with [thingiverse/thing:3738687 by SantiMZ], and added an assembly for the ESP32 and the associated electronics. All parts are inserted in a standard PVC pipe which is fixed on top of a water tank. A mobile cover protects the…
Print approx. €1.06–€1.29 excl. taxPreliminary estimate for PETGSource material: PET
Print settings (example) Raft or Brim: None Supports: No Layer height: 0.2 mm Infill: 100 % Screw hole is 4mm diameter.
Currently refining a small obstacle avoiding mecanum robot for an introductory robotics club and needed a simple mount for a servo driven ultrasonic sensor. This design is a single piece print with no supports that printed quickly in PLA+…
Just added the smile like on the original design https://www.thingiverse.com/thing:1364024 :-) Fits perfectly Ultrasonic HC-SR04 sensor and standard servo mount Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2…
Printing: There are no special printing requirements, NO supports . For example 0,05mm layerheight, 2 perimeters, 100% infill. print max 3-4 layers.
This is the case for HC-SR04 ultrasonic sensor (RED VERSION). The blue one has diffrent dimensions and is not compatible with this case. Print Settings Rafts: No Supports: No Filament: Doesn't matter Category: DIY
a minimal case for a HC-SR04 sensor, fits without screwing.
Print with 20% infill After printing, the case is ready to slide onto the transmitter and receiver on the HC-SR04.
This is a case for a HC-SR04 ultrasonic sensor which is part of water level meter project by using Arduino. The case printed using TPU. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2…
I just flattened the foot and added a groove for a servo mount instead at the bottom. A great tutorial on how to make a arduino radar can be found here: http://howtomechatronics.com/projects/arduino-radar-project/ Category: Engineering
This is a casing & supporting cradle for HC-SR04 (Ultrasonic Distance Sensor). Key features: No screws or adhesive need to assemble the unit itself. The vertical angle of the HC-SR04 can easily be adjusted by tilting it up or down in the…
Find english version below... Box bzw. Behältnis zur Aufbewahrung von AA-Akkus (HR6) und/oder AAA-Akkus (HR03). Unterschiedliche Bereiche und Farben dienen der Unterscheidung ob die Akkus VOLL aufgeladen oder LEER sind. Die…
Printing: There are no special printing requirements, NO supports . For example 0,05mm layerheight, 2 perimeters, 100% infill. print max 3-4 layers.
Arduino compatible Ultrasonic sensor Buy the HC-SR04 Sensor HERE
5° tiltet holder to correct the tilt of the sensor
On my occasion I will end up gluing the box to another surface :)
Use M3 screw for installing
This is a housing for a NoceMCU v3 and an HC-SR04 ultrasonic distance sensor. The lid will stay on when held upside down, but it's easy to remove. I designed this together with my son as an introduction to 3D modeling. Print Settings…
I used JSN-SR04T waterproof ultrasonic sensor to calculate the water level in a water tank. The idea is to calculate the distance to the water level and use that number to calculate the volume of water inside the tank. The sensor is…
This is a printable design to mount the HC-SR04 ultrasonics sensor to the Micro SG-90 To make this design work you'll need four small screws (or two - for each opposing corner) to mount the ultrasonics sensor to the print. And you'll need…
JSN-SR04T Waterproof Ultrasonic Distance Measuring Module case with lid. Feel free to remix if needed, the lid is very tight the first time you try to put it on. I need to find a way to get it to not move around so much inside even…
Spoor 1 - Ketel BR01 (lading) / Spur 1 - Kessel BR01 (Ladung) / Gauge 1 - Boiler BR01 (load) Scale - 1:32 This load for Gauge 1 model railways is highly based on the boiler fitted to Deutsche Reichsbahn Baureihe 01 (Altbau) steam…
This is a set of mounts you can print to hold your HC-SR04 Sonar Range Finder in the front (or back) of an Arduino Smart Car. The images show how to mount it. Please note that the three of them have different mount shapes to match the…
purpose this mount offers rugged angular adjustment even on rocking platforms for sensors AJ-SR04M / JSN-SR04T, used in many arduino/raspi-zero etc projects. material if you platform is used in direct sunlight, don't use PLA, as it will…
This is my latest attempt to get the HC-SR04 to measure reliably the water level in a tank. Previous attempts with the waterproof JSN-SR4T ended in erratic results due to multiple reflections from the tank walls especially at low water…
Description This case is designed to house a Wemos D1 Mini and a JSN-SR04T ultrasonic distance sensor. It’s ideal for use with ESPHome and Home Assistant to measure distances, such as monitoring the level in a water tank. Design Overview…
This is a custom-designed holder for the HC-SR04 module, ensuring secure mounting and alignment. It features: Top or Bottom Mounting : Two M3 holes with a 20mm center-to-center distance for attaching the holder to other surfaces. Also…
Print using PLA or PETG. Add a M4 screw with butterfly nut. For the centering pin I used a 3mm old drill bit which I cut to size (about 10 mm) and inserted to the base by heating it first. You can view the Onshape design at…
This mount is used for mounting JSN-SR04T water level ultrasonic sensor on top of the IBC lid.
This 3-part 3D printable housing system allows you to install an ESP32 and HC-SR04 sensor into a waterproof container or tank lid for use as a smart fill level sensor. It’s perfect for home automation projects using ESPHome and Home…
To keep the files size down, there is only one wheel shaft, you will have to print 4 of them, one right wheel and one left wheel, you have to print 2 of each. And one main axl, you will have to print 2. Suggest you scale up to the max…
Requires BS_Joint.stl from https://www.thingiverse.com/thing:2427726 Category: Electronics
Edited from Eric's description This is designed for 1st ACs and other camera department members that use a Robocup and need a place to set a few items down. Holds 1 sharpie, couple lumocolor pens and couple sharpies, most smartphones,…
This is a case for the HC-SR04 ultrasonic sensor. I made it especially for outdoor use because I need a sensor for measuring the water level of water tanks. The sensor cable can be fixed with a cable gland (M12). If you fill the case with…
This supports are designed to hold the HC-SR04 ultrasonic sensors to the wall. It is ideal for monitoring the level of your tnaks or your wells. The two pieces are holded together with two screws and the cable of the sensors passes…
Printed with Prusament Jet Black 0.3mm supports are required.
an open robotics platform ( https://openroboticplatform.com/ ) compatible holder for the HC-SR04 ultrasonic sensor. attaches with 2 M3 flatheaded screws (height of the head of the screw should be around 2mm). sensor is easy to mount,…
Habe den Spoiler in Eryone TPU 95A gedruckt was ihn unzerstörbar macht. Drucker: Bambu Lab X1C 0,2mm Layerhöhe 0,4mm Düse Keine Supports Brim Außen Wenn ihr das gedruckt habt dann würde ich mich über eine Bewertung und ein Make freuen…
Scraper Bar Replacement for Greenworks Part R0200650-00 for 22" Snow Blowers, Tested working great with my SN60L02 but according to Greenworks should work with the following as well: Product Number Voltage Model 2605902 80V SNB403 2610102…
Accurate model of the HC-SR04 Ultrasonic Distance Sensor along with a 3d printable mount for it.
this is a remix of the original H-SR04 minimal case by KIKO64. i tagged this as a remix but it not really a remix since i designed it from scratch also adding some different backs. the reason why i made this is that my chinese sensors are…
Habe für die Jomurema Karosserie eine Klipp+Bumper Kombination konstruiert damit diese länger hält. Der Bumper passt 100% perfekt rein und das mini Teil um die Federn vorne zu halten ist auch mit eingebracht so das man da nicht immer…
I printed in 0.2 mm nozzle on a p1p with a basic autogenerated tree support
Pointed at 10 degree angle, to look down at stuff
Use 3mm screws to assemble side plate to base. Holds 48 AA batteries easily. This was my first attempt at designing a dispenser of this type. I have adjusted a few things in this version from the original prototype I printed. In all it…
Plate to hold lenses inside the BetaFPV VR03 FPV goggles as the goggles are smaller than all tested glasses frames. (Needed size is ~110mm) Print two plates - with the bed side of the pieces facing inwards. Needed as the is a chamber on…
GRAVITRAX ; Though you would like to be able to build a column on top of where you drop the ball through the plate? You also can use this drop in half-way up the column. GRAVITRAX; Height stone 25 mm with 14 mm diam. hole and roll in…
This JSN-SR04T Ultrasonic Sensor Lid Insert is designed for use with IBC water tanks. It's an easy way to install an ultrasonic sensor to measure water levels accurately.
Windshield mount for the Aukey DR02 dash camera. I printed the one this is remixed from and it was too loose on my camera. This fits much more snugly. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: .2 Infill: 20-40…
layer 0.20 remplissage 30% pas de support
Traditional nutcrackers are so old-fashioned, now you can use the CR0NCH3R instead! CR0NCH3R is a little dude that chews as aggressively as you can press down on its lever or antenna. Made of many parts, it is easy to print and satisfying…
This is a case for the Qwiic Ultrasound Sensor https://www.sparkfun.com/products/17777 that can be mounted from behind. It also works with the identical (apart from colour) Zio Ultrasound Distance Detector…
Quick to print replacement keyboard leg for logitech Y-R0067 keyboard. While 3d printing I used supports but it may be possible to print without them.
For a school project we are using the Joy-It robot car. On this car we have to mount 2 HC-SR04's. I did this with the help of this (self-made) model. As you can see the sensor fits perfectly in the mounting piece and the mounting piece…
La caja es rectangular, de color negro y con un diseño minimalista. Presenta un hueco en uno de sus lados, especialmente pensado para permitir la conexión de los pines del sensor HC-SR04. No tiene líneas ni detalles adicionales en la…
Threaded cone for ultrasonic distance sensors. Thread diameter: 28 Thread pitch: 2mm Heigth: 66mm Outer diameter: 44mm Inner diameter: 21.8mm Category: Parts
simple mount to put a SR04M (or SR04T) to a beam on my carport to detect a parked car
Sensor bracket for the HC-SR04 sensor . Using this bracket you can mount the sensor on top of a servo motor.
As requested here is a AAA version of my AA Battery Dispenser. This should hold over 48 AAA with ease. I haven't had a chance to print this one yet, but based on the lessons learned from my AA dispenser prototype, this AAA dispenser…
Remix from https://www.thingiverse.com/thing:1799012 Allows housing for both HC-SR04 and HC-SR501 for when you need both motion and distance detection. It also fits a small microcontroller in the rear, though you will need to use glue or…
Holder for the X-axis cable wrapping; The only one moving one that in the kit stays loose. Recommend to print in ABS and use 2 layer raft
Hexagonal sensor mount for JSN-SR04T ultrasonic sensor
One of My models from My Road Rage series Printed on the Elegoo Saturn 3 ultra Scale up to the size you need. All models now available https://www.cgtrader.com/designers/dna001 Please leave some comments good or bad, thanks Check out My…
Wall mount for Makita trim router XTR01Z. This might fit corded models but I do not have one to confirm. This has four countersunk holes, but it is also easy to join with an Honeycomb storage wall or other similar wall organization…
This is a custom-designed scanning mount for the HC-SR04 Ultrasonic Distance Sensor , specifically engineered for obstacle-avoiding robots and Arduino projects. The design consists of two parts: Servo Base: A cylindrical housing designed…
This is mainly dedicated to FPS players and all those, who like light or well-balanced wireless mouse. Super lightweight and easy to do adapter from AAA to AA! Example: Razer Pro Click Mini is probably the best mobile office wireless…
hc-sr04 sensor compatible with an arduino It's easy to attach the model to a contruction with bolt and nut or screws. No specefic printing instruction needed.
Mini toy sci-fi lunar rover buggy. It features a lift up rear hatch with a small load cargo area, four working hubless wheels, and long travel independent suspension. Great for those looking for a non-franchised and non-weaponised space…
This is a mounting bracket that holds a JSN-SR04T ultrasonic sensor and waterproof DS18B20 temperature sensor for mounting to a 1" square tube. This is part of a project to measure the water level of a creek. The sensor will be extended…
Holes in this model is modeled for M3 screws . The hole is in the middle of the bottom part. Sizes on pictures are in millimeters.
A cute Alien design for an ultrasonic sensor (HCSR04) enclosure. It's a snap-fit box and doesn't need any screw..
Habe hier Lenkhebel für das MR03 Chassis Konstruiert die Perfekt passen.Man sollte allerdings die Pins der Federung umdrehen was aber eigentlich eh jeder macht.Die Welle der Achse sollte man auch mit Sekundenkleber einkleben. Diese…
Boîtier pour capteur ultrason HC-SR04 destiné à la fixer à l'aide de deux aimants de diamètre 15 mm. Deux parties imprimables.
Parts are easy and fast to print I used PLA and PLA+ for filament Lid for the case is snap on (you can use some CA-glue to hold it firmly). Battery has its own compartment in the bottom of the case, but I used some strips of duct tape to…
Hello, I'm uploading my own version of an ultrasonic HC-SR04 sensor holder. This design has a tight fit, so please be careful when inserting the sensor. To print, please place the gadget in the orientation shown in the photos. This will…
Wenn man seinen Mini Z EVO auf das PN 2.5 Chassis umbaut merkt man das die Empfänger Platine nicht gehalten werden kann und genau dafür habe ich eine Klammer konstruiert die absolut Perfekt passt und somit die Empfänger Platine auf dem…
I designed this Mini-Z MR03 Front bumper for Jomurema GT-01, compatible with aluminium front lower suspension.
This is a case I drew to hold my SR-04 that I use for Inventr.io lessons and also for DIY prototyping projects. It snaps together requiring no glue. Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2 Rafts: Yes Supports: No…
20x20 aluminium profile HC-SR04 Ultrasonic Distance Sensor holder. Printing instructions: 0.2 speed profile. Supports active from the print bed. Happy printing =)
Dieser hochwertig 3D-gedruckte Sensorhalter wurde speziell für den HC-SR04 Ultraschallsensor entwickelt und sorgt für eine sichere, stabile und passgenaue Befestigung in deinen DIY- und Elektronikprojekten. Ideal geeignet für den Einsatz…
Use this plate to hold lenses inside the BetaFPV VR03 FPV goggles. Print two plates, screw together with lens inside and place in goggles. Compatible with lenses you can buy on Amazon using following link: KoKoBin 2 pacco Occhiali da…
This model holds up an HC-SR04 ultrasonic sensor upright for easy use. The photo shown is tpu, however it should work with other materials such as PLA or PETG. useful for robotics applications. 2 models, one shorter one and one taller…
RYKO ROLLER01 Deutsch: Filament Abroller zur eigenständigen Nutzung oder als Teil einer Trockenbox mit Temperatur und Luftfeuchtemessung. Das Modell besteht aus 3 Druckteilen (1xGrundplatte und 2x Rolle). Weiterhin werden 4…
Boite de rangement de piles et batteries pleine et vide. Petit aide-mémoire sur le couvercle pour séparer les batteries vides des pleines. Les vides avec le - vers le haut, et les pleines avec le + vers le haut Deux modèles (simple ou…
Rangement piles LR06 AAv Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,28 Infill: 20 Filament: Geeetech PLA Grey Notes: Rangement piles LR06 AA Category: Organization
This is a CV Joint Boot for the front left CV Joint on a Land Rover Range Rover - original part number LR032576 ... works exact the same as the original but for fraction of the costs if made on your 3D printer using TPU
Rangement piles LR03 AAA Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,28 Infill: 20 Filament: Geeetech PLA Grey Notes: Rangement piles LR03 AAA Category: Organization
I love my Ridgid tools - more than two dozen. I've been waiting for the weed eater, now I have no electric nor gas powered tools. No more gas cans, no more disturbing noise. And you can't beat the Lifetime Warranty - even on batteries!…
Holder intended to be glued into DN600 manhole ring
This 8020 series 10 mount adds a connection point for wire ties. It does not need a special printed tool to remove the sensor from the mount. It can be used standalone. Print instructions Category: Electronics
We needed to mount HC-SR04 ultrasonic sensors onto our Arduino robot. I couldn't find one that had the right dimensions, so I made my own. The sensor technically goes in upside down, which allows for easier access to the pins. Attachment…
