Counting matching models…
Welcome to the SimpleCore 3D Printer, the latest version of my large 3D printer design. It's easy to build, budget friendly CoreXY 3D printer featuring the Eva3 toolhead platform and a Triple Z bed system. This printer is designed to be…
I love the belted Z of the Simplecore, however, with the stock direct drive setup, the bed tends to drop like a rock, especially for larger builds when motor power is cut. To fix this, I've designed new motor mounts that add a 4:1 gear…
Adapted SimpleCore XY to use MGN12H
Has to be printed on the flatside. Didnt bother flipping them the correct way x)
This is a mod for the SimpleCore Redux that moves the linear rail to the front. It allows for better COM and full compatibility with Monolith based toolheads! The files are ready to print and I have included .F3D and .STEP for those who…
Modified z-axis carrier and idler for the SimpleCore Redux. The original single tensioner screw and captive nut have been replaced by two screws and threaded inserts. This carrier and idler is a direct replacement for the original part…
Complete CAD for A4T Bambu Labs toolhead and beacon probe mount
Allows mounting SimpleCore motors to 2040 profile
Pictures are version one in which the belt geometry is off (you can see the belt pulled in). attached files run the slider full height, and the face of it 5mm closer to the rod (should have the belt straight/much closer to straight).…
For BBOX or simplecore I had some problems with the z system on my BBOX so I adapted this system from the simplecore since this two are very similar printers, THIS IS NOT TESTED partially... this is a correction of my files, my previous…
my short ruthex m3 incerts just dropped in the original holes.. no heating required... (and i geuss it could be hard to get an iron in down there.. i used ordinary length ruthex M3 incerts on the "new poles" in the bottom plate i also…
This is a mod for the SimpleCore Redux that allows you to use MGN12C linear rails on the Y-Axis, ideal for those who cannot source T-SLOT 2020 extrusion easily, this will stick out of the frame by 4mm so please take that into account. The…
I wanted to use a DIN rail mounting solution similar to the Trident for my SimpleCore Redux, but was unable to span two pieces of DIN rail across and still fit all of the electronics due to the belted Z-axis assemblies underneath the…
[ENG] This explanation was translated using DeepL. We apologize in advance for any errors. This improved double shear mount features repositioned holes to accommodate a hex wrench insertion space, making installation slightly easier. Use…
BOM: Qty 2 - M4 Hex Nuts Qty. 4 - M4 Knurled Nuts: https://www.mcmaster.com/90368A200/ --OR-- Qty. 4 - Silicone Bed Spacers CR-10 Hotbed: https://a.co/d/25VRBL Print Settings: Material Used: Inland (Micro Center) PETG-CF I just followed…
These revised rear idlers that allow for the use of toothed idlers in lieu of the smooth 695 bearings from the BOM. NOTE THAT THE BOM TOOTHED IDLERS FROM THE XY JOINTS WILL NOT WORK. The thick flange does not allow room for a washer…
Revision Log 2026-02-09 -- Initial Release 2026-02-10 -- Added vertical ribs for stiffness. BOM: Qty 6 - M3 Brass Inserts Qty 12 - M3 x 8 Flat Head Cap Screws 4 to attach each motor to the carriage. 2 to attach each retainer to the base.…
Provides more support to the motor shaft, hopefully prolonging the life of it. Uses F695-2RS bearing (already on the BOM for the Simplecore). Edited to add mirrored copy
The feet sit up nicely against the skirts, so they will not rotate once attached. BOM: Qty 4 - M6 Nylock Hex Nuts Qty 4 - M6x20 Hex Bolts or SHCS Print Settings: Material Used: Overture TPU 95A Layer height: 0.2mm Infill percentage: 15%…
Welcome to the SimpleCore 3D Printer, the latest version of my large 3D printer design. It's easy to build, budget friendly CoreXY 3D printer featuring the Eva3 toolhead platform and a Triple Z bed system. This printer is designed to be…
For BBOX or simplecore I had some problems with the z system on my BBOX so I adapted this system from the simplecore since this two are very similar printers, THIS IS NOT TESTED partially... this is a correction of my files, my previous…
my short ruthex m3 incerts just dropped in the original holes.. no heating required... (and i geuss it could be hard to get an iron in down there.. i used ordinary length ruthex M3 incerts on the "new poles" in the bottom plate i also…
