Counting matching models…
A mount for the cartographer probe on the switchwire/enderwire. It's a remix of the x carriage and the belt grippers to provide clearance for the probe and wires. Mount requires two more heatset inserts into the bottom of the carriage and…
Compatible with enclosure as it acts as both camera holder and panel holder. To mount it, I used an M5X20 screw with an attached nut to make it like an M5X18.
A mount for the cartographer probe on the switchwire/enderwire. It's a remix of the x carriage and the belt grippers to provide clearance for the probe and wires. Mount requires two more heatset inserts into the bottom of the carriage and…
I double-sided taped it to the top panel and used the wire organizer to run USB cord. Mount Uses one M3x30mm bolt with M3 Nut
Needed a way to mount the 60mm electronics cooling fan on the switchwire or add a second one Middle skirt modeled to eliminate mounting points for the Mini12864 Bodies on holes can be used to add infill pattern or multicolor to the skirts…
I promised to cad this up ages ago and as soon as I actually started rebuilding my enderwire I actually did it. Inspired by RockAndRoll for the 2.4, you can tip an open or enclosed Enderwire on its side and and it will be stable. Yes my…
couldn't get tinkerman's mount to do what i needed without drastic modification, but was inspired
Strain relief bracket for the MK52 heatbed on a Voron Switchwire build. Improving on the LDO kit design, this part anchors the bed wiring at a right angle, routing the cable loom away from the enclosure panels, preventing the wires from…
This is a PUG mount for a big boy Switchwire with the standard 3-hole drag chain on the Z axis. I made it because I couldn't find a working PUG mount for my LDO Switchy. It might work on an Enderwire. You'll have to test it to be sure. If…
This is a set of feet and handles designed to allow you to easily lift an enclosed switchwire. You can also safely roll your switchwire on its side for electronics bay access. The handles were designed to fit the siboor ender to…
This is a Voron Switchwire XZ joint mod that replaces the original screw-as-pin setup with proper locating pins. In the stock design, the bearing inner races ride on threaded screws, which can introduce unwanted looseness and gives the…
This is a simple mount for the Pi Camera 3 that attaches to the back of the printer. Installation requires removing a single bolt, then securing the mount using that same bolt through the camera mount. To attach the camera, you will need…
BTT Manta M5P mount for Enderwire. (5) M5 x 10 screws w/ (5) M5 Spring nuts needed to mount to frame, (4) M3 heat inserts m3x4x5, and (4) M3 x 8mm hex screws.
Revamp of the original screen mount by Fizzy . Added buttons to the bottom of the print. No glue or extra parts required. Made screw holes sturdier. Added chamfer on bottom layer to prevent elephant foot.
Voron Switchwire Double Shear Motor Mount This mod adds another bearing on the motor mount to support the other end of the motor shaft. It reduces the bending effect on the shaft caused by the tension of the timing belt. In theory it can…
This combines the top door latch with a C270 Mount Uses one M3 M3x30mm bolt with M3 Nut
This is a remix of Giwi's Enderwire Logitech C270 Webcam mount but with cable management. As before, replace the original M3x16mm screw with an M3x20 to mount to either the left or right XZ bearing block (I prefer the right and have…
Compatible with enclosure as it acts as both camera holder and panel holder. To mount it, I used an M5X20 screw with an attached nut to make it like an M5X18.
Remixed Banzaito's model to have holes for an igus cable chain as they are often included in Ender 3 to Switchwire kits.
Remix of the Switchwire X-Carriage so you can mount a Revo Voron PZ Probe board on the carraige with M2 screws.
Requires the following hardware 2x M3x4x5 Heatset inserts 2x M3x8 SHCS Part A needs supports to print correctly.
Based on the great work by boubounokefalos in his Ender 3 to Switchwire conversion. I adapted the y-axis cable chain to work with the Ender 3 Pro (v2 also). It reduces the space allowance we need at rear, especially if you want to place…
Copyright: this model contains parts from https://www.printables.com/model/185127-ar-cable-chain-link-opened and https://www.printables.com/model/411425-voxelab-aquila-switchwire-y-axis-bed-carriage-mgn1 licensing info is provided in the…
Mount your klipper expander centrally for easy access to the wires + routing. BOM 2x M3x12 2x 2020 M3 t-nuts (or rollins) for your center extrusion 2x M3 heat set inserts 2x M3x6 (or longer) Printed with ABS, 0.4mm nozzle 0.2mm layer…
I added the infill to the hexagons to allow custom meshes to be applied. Standard Voron settings 0.25 first layer Mesh part I used 0 walls/perimeters 0 top/bottom 20% infill Honeycomb
This is my 3rd revision of this mount for a Raspberry Pi 3B + BTT Octopus (PRO) for undercarriage mounting, It attaches to the 3030 extrusion via 3 M5 bolts and then to the underside of the Y carriage via 3 M3 bolts + the needed M5 & M3…
The mount fits into the right z_bearing block, but you will need longer M5 screws (+1cm). It allows to use all PUG models. You will need to print the modified part with supports. Otherwise print with Voron settings.
Printed with VoronDesing parameters. Walls: 4 Filling: Gyroid 40% Material: ABS Tools used 6xScrew M3x16mm 2xheatinsert M3
Modified Switchwire bearing cap, since the original one does not fit to the remix.
These are the parts I utilized for my YT series on revitalizing the Voron SwitchWire. Please note, these are modifications of original parts and work well for me however they might not work for you, I am utilizing a Rapido 2 UHF nozzle…
I double-sided taped it to the top panel and used the wire organizer to run USB cord. Mount Uses one M3x30mm bolt with M3 Nut
For materials, instructions, and for the other final printed part, visit @LivingroomWorkbench's original model: https://www.printables.com/model/560244-ender-switchwire-bed-cable-extension
A camera mount for the Voron Switchwire (enderwire specifically, I'm not sure if the front panel brackets are the same). This uses a heat set insert (m3) for the front panel bracket, in order to mount the camera. I designed it for this…
I don't know that this will work on a conversion, it was designed for an LDO kit. Requires a Voron spec heat insert, M3x8(?) screw, M5x16 screw, and the Nevermore 1515 mounting flange. I sanded the extrusion alignment tabs off the flange-…
Mount to secure a Nevermorev4 filter to the front of a Voron Switchwire (at least with the dimensions in an LDO kit). I didn't want to have to permanently mount it anywhere with VBS tape, so this just replaces 2 M5 screws for M5x10s. Also…
voron switchwire / ender 3 y linear rail motor mount with ender 3 original endstop reposition
what you need: 5x F695 bearing 6x M5 1mm spacers 1x MGN12H Linear Rail - 300mm 5x 20t GT2 pulleys 2x Stailess Steel Rod 5x60mm-Grind Flat 1x GT2 Closed Loop Timing Belt 324mm 1x 2020 Extrusion - 340mm 1m gt2 belt 1x stepper motor Printed…
**WARNING:** Use a flat flexible USB-C cable when using the ADXL345! A standard connector will interfere with the X Endstop Switch, might break your ADXL345 board and/or USB cable. I was already using a MicroSwiss NG Revo prior to doing…
An endstop for the stock voron switchwire (as opposed to the enderwire like the linked model) with the galileo2 extruder.
Purchased the Fysetc DSI display as it was much cheaper than the BTT one but found that it's a much slimmer display with the ribbon cable in the middle instead. Remixed to make it work for the Fysetc 5" DSI display. Update : Added a…
Remixed the base to be printable without supports. Uses the same hardware as the original model. Now with PG-7 support!
(Untested) The name says it all
Info more open degree front panel can be remove Parts required /tools required printed parts 3M scotch flexi tape or VHB tape 4x SHCS M4x50mm Print instructions Filament material: ABS/ ABS+ Layer Height: 0.2 Infill: 20-40% Supports: No
As much as I enjoy the aesthetic of the standard Switchwire XZ motor mounts with their slick belt tensioners, I found I have issues with the standoffs on my Enderwire Max cracking. I really like the style of the Gizzle motor mounts and…
Couldnt find anyone that made hex skirts for Switchwire so here you go.
Needed a way to mount the 60mm electronics cooling fan on the switchwire or add a second one Middle skirt modeled to eliminate mounting points for the Mini12864 Bodies on holes can be used to add infill pattern or multicolor to the skirts…
This mod allows for your Switchwire panels to be double hinged for easy internal access. By the power of VHB Tape, just replace some of the panel pieces with the panel clips, and refer to this image for assembly, mirror on the other side.…
use the mount hook from the original model.
Reverse engineered and recreated version of Ender 3 / Pro LCD display enclosure for Voron Switchwire and Enderwire printers. I contacted the author of the original design from here:…
Original model description from Silpstream , including BOM and links for 10x11 chains (works fine with R18 10x11 Open), below. Only notable difference in BOM is that the flipped frame mount uses an M3 screw and T-nut instead of M5, and…
Enhance the aesthetic of your Switchwire or Enderwire setup with these stylish raised Voron logo skirt covers . Designed to be easily dropped into existing skirt mounts—no MMU required—they elevate your machine’s look with a subtle yet…
BigTreeTech HDMI5 1.2 mount for the Switchwire or Enderwire.
I promised to cad this up ages ago and as soon as I actually started rebuilding my enderwire I actually did it. Inspired by RockAndRoll for the 2.4, you can tip an open or enclosed Enderwire on its side and and it will be stable. Yes my…
couldn't get tinkerman's mount to do what i needed without drastic modification, but was inspired
This is an adapter for mounting a Nevermore Micro V6 inside a Voron Switchwire (standard Voron dimensions) near the front-left panel. Note: Depending on the length of your Y chain it may hit the adapter when homing and when printing on…
Just a upload of my close to stock 120x120x120mm Voron Switchwire. Youll have to CNC/jet cut the Y bed carriage or print out a dxf of the part on paper, glue to a piece of aluminium and do it by hand. Use it if you want to, CAD missing…
a mount for the hdmi 5 by btt for the switchwire/enderwire
The blocks have been remixed to suit the MGN12C linear rails for those who need them. Category: 3D Printer Parts
I took the original PG7 - 2 file and created a version for two hole cable chain and had the PG7 thread be at a 45 degree angle so the umbilical would not hit the top of the enclosure when printing the full print height.
The original Voron Switchwire 2020 mount had two bolt holes and was longer than I needed. The extra length was in the way of wiring channels that I wanted to put into place. So I remixed as a shorter version with one hole.
2 hole version for siboor cable chain Printed in Abs standard Voron Settings
use M4x50 screws. clearence for screws are 4.10mm. i make it snug so upper piece holds the screw even on removed.
holder for a 25/26cm led strip for the Voron Switchwire
Move the x end stop to the gantry cause no end stop mount on Jabberwocky.
I wanted to cover the belts of my Voron SW as the filament rubs against it sometimes uses 4 screws M5x10 and 4 3030 M5 slide in nuts
EBB36 Orbiter 2 Side Mount for Switchwire with Dragonburner
Adapter plate to fit an ApolloLander/ApolloMini to Enderwire and Switchwire (and other voron mount) You can get the Apollo on my Patreon (here) nozzle height is the same as stealthburner, so you can use a probe in the rear block, like an…
Full video guide for the conversion can be found here: This conversion only includes the x and z axis, not the y axis. Files needed to convert the y-axis can be found here:…
Bolt-on umbilical adapter, Goes behind the top of the vertical drag chain on the x-axis. Use zip ties to secure the cable to the adapter. See also:
XL Foot for Switchwires 2 perimeters 30% giroid infill top/bottom layers: 4
Strain relief bracket for the MK52 heatbed on a Voron Switchwire build. Improving on the LDO kit design, this part anchors the bed wiring at a right angle, routing the cable loom away from the enclosure panels, preventing the wires from…
I created this to utilise PanzerObserver's OV5648 Camera Mount in my Voron Switchwire prior to attaching the panel enclosures. It allows the camera to be positioned high up at the front as if attached to the top panel. The model uses a…
Tired of adjusting belt tension by moving the motor? This solves it. This is a simple and compact belt tensioner designed for Voron Switchwire and Enderwire (XZ axes) . No need to loosen motor screws during adjustment The mechanism works…
This is a PUG mount for a big boy Switchwire with the standard 3-hole drag chain on the Z axis. I made it because I couldn't find a working PUG mount for my LDO Switchy. It might work on an Enderwire. You'll have to test it to be sure. If…
This is a set of feet and handles designed to allow you to easily lift an enclosed switchwire. You can also safely roll your switchwire on its side for electronics bay access. The handles were designed to fit the siboor ender to…
This is a Voron Switchwire XZ joint mod that replaces the original screw-as-pin setup with proper locating pins. In the stock design, the bearing inner races ride on threaded screws, which can introduce unwanted looseness and gives the…
This is a simple mount for the Pi Camera 3 that attaches to the back of the printer. Installation requires removing a single bolt, then securing the mount using that same bolt through the camera mount. To attach the camera, you will need…
printed in abs 40%infill 5 perimeters 5 top and bottom layers cut a 110mm ptfe 3mm tube to insert in the slot for the spool to slide on. original design by Voron Design
While converting my Ender 3 V2 to a Voron Switchwire, I noticed that the standard conversion relocates the Y extrusion and secures it with only two screws. I wasn't comfortable relying on only two fasteners to hold a structural frame…
printed in abs 40%infill 5 perimeters 5 top and bottom layers original design by Voron Design
I wanted to use the trident like ender switchwire fan grills and the stock inlet and switch on my Switchwire conversion so I remixed Fizzy's model to match my needs
I modified a lot of parts to fit my need like installing mgn9h railings and 623 bearings for my enderwire project. For the base i used voxelab aquila frame. Its the same as ender 3 v2 frame . Ender 3 pro have 2040 y axis frame. You need…
Reaper Switchwire Carriage A custom version of the Reaper carriage designed for Voron Switchwire . I wanted to use the Reaper toolhead on my Switchwire conversion, so I designed this carriage with the help of APDMachine. Overview This…
Fysetc Spider mount for the Voron Switchwire 3D printer. Uses the same dimensions as the spec SKR Mini E3 mount so the BOM hardware will not change. (4x M3x8mm, 2x M5x10mm)
I made myself 3 mm thick printable deck panels for VORON Switchwire, since I did not have immediate access to acrylic and did not like other forms (like kartonplast). Model was made from original DXF file available on GitHub. I added a…
This is a simple printable 2 part deck panel for the Voron Switchwire. I've added 3 additional mounting holes to better align the panels, and more rigidly mount them. The panel is split in 2 parts that just fit on the VSW build plate. I'm…
Utilizes empty space in 60x30 extrusions of Voron Switchwire frame to store printer accessories. Modeled to fit into LDO provided extrusions. Both front and back caps can be replaced by drawers. Two lengths included 150 and 200mm. Unlike…
SKR Pico mount for a switchwire conversion. When Stacking the Pi onto the Pico you need additional feet for the needed space. Remixed from the SKR Mini E3 mount from boubounokefalos' Ender Switchwire Conversion.…
Print in abs, asa or any material that can withstand the heat, 40% infil, 4 outside walls, 5 bottoom and top layers, layer high at .16 mm. Assembly requires 4 m3x8, 2 m3x10 and 2 m3x50. Step file its included in case you need to do…
M5 T-Nut for 3030 Extrusion You'll need a M5 bolt. Useful for non structural or light duty parts, like Voron Switchwire panel mounting. Print Settings Printer: Voron Switchwire Rafts: No Supports: No Resolution: 200 Infill: 40 Filament:…
Tool holder for spatula and side cutter for the Voron Switchwire. It can clip with a tight fit to the side of the 3060 extrusions, or you can slide it by removing the endcap. I used tree support to print it. Print Settings Printer: Voron…
This is a remix of several parts to mount a Hemera on a Voron Switchwire. I have abandonded this project and preset it as is. There will be no further changes. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament:…
This repo contains the STL for Voron SW SB CR Touch Mod. I used the SB 1.05Beta during development. But it should work on the SB v1 release as its only X rail carraige. The STL is only for MGN12 Carraige for SW No supports are needed…
This design doesn't work for the MK3, as it will not clear the linear rod. I've been undergoing a long project to convert my Geeetech A10 (basically an Ender 3 clone) to a Voron Switchwire. As part of the changes, I added a MK3 Y…
