32 models
This thing is to help the internal fan of your Tacx Neo (every edition!) to get rid of the heat. After reading so many complains about overheating Neos I decided to design a fan mount which helps the neo to suck air out of the housing to…
This model is used to reduce the amount of vibrations transferred to the floor that get produced by the using the Tacx Neo 2T. In my opinion this makes it not only less noisy to others in the building but also to your self. Besides the…
Print in ABS with gyroid infill and 6 walls. Print direction is upside down (like a funnel). No supports needed.
This adapter wasn't buyable so I created it myself. Tolerance: 0.3mm Print it with something strong like ABS or CF20.
This is an improved internal fan for the Tacx Flux trainer. This part is mounted on the fly wheel providing cooling air towards the magnets and PCB. The original part mounted in the Tacx Flux trainers casuing internal clashes and bad sound.
Once a year, when the days get shorter and it gets wet and cold outside, I think it's a good idea to get my Tacx out of the corner and go for a ride or two indoors. And once a year I break off the lever. This year I decided not to simply…
The pre-load nut for the left crank arm is inspired by the Shimano Hollowtech II design, but smaller. This tool allows you to tighten the nut by hand before torquing the pinch-bolt.
This is adapter for tacx tablet holder mounted on handlebars for indoor bicycle trainers. https://www.garmin.com/en-US/p/690898 Since aero bars are flat 52x27mm in size, the original tacx holder can't be mounted on them, this model…
The Spider bike repair stand holds the bike by one axle, while the bottom bracket rests on the center section. It comes with a set of adapters for different axle sizes, but I am missing the 15x110 and 12x148 sizes for my mountain bikes.…
Adapter to attach a bike with thru axle to the roller trainer
This adapter uses steel pipes to fit the thru axles themselves to the adapter. The pipes have a frictionfit in the adapter. Outer diameter is 17mm, inner diameter 12mm. Lenght for the front wheel is 100mm, rear wheel uses a 142mm piece.…
Maybe will help somebody... I needed to replace broken plastic lever for the engine in Fortius Tacx T1940. I printed with 12 perimeters, but in general it matters to have max perimiter count in the most fragile place (you can see on the…
If you like me 50+ and your eyesight on short distance fades slowly, you might want to use the Zwift companion app on your tablet instead your phone. Unfortunately I could not find a bike mounted tablet holder for portrait mode. I bought…
It can be challenging to mount and dismount a bike when it's on the dynamometer, so here's my solution. It's a pair of steps to mount on the side rails of a set of Tacx™ Galaxia rollers. These steps will allow the rider to mount and…
Prints well in TPU. Lost one of the rubber feet so just modeled it up and printed it.
Erhöhung für TACX Vorderrad Halter, einfach zum einstecken. Gummi einfach vom originalen Halter in die Erhöhung stecken
Having problems with your grining Tacx Neo (1 and 2) and even installing a third o-ring did not solve the issue? Print this, take a single o-ring of your already installed o-rings and put it on the axle facing the o-ring inwards. One…
Description: Breathe new life into your classic Tacx Spider Team T3050 workstand! This adapter allows you to mount modern road bikes and gravel bikes with 12x100mm front thru-axles. Unlike other adapters, this design does not require you…
In certain cassette (for my case a 12 speed shimano 7100 but also happens with 8100) the inner most position provokes a grinding of the derailleur arm against the rotating disc on the trainer, this is a known design flaw. Adding a spacer…
I found that none of my bigger bikes fit on my new TACX T3050 work stand. This adapter fits my XL frame full suspension fat bike with room to spare, so it likely fits your bike too! The end is tapered so you can press fit the extension in…
I've made this funnel to pour powder in my sports bottles. This makes less of a mess when preparing. My brand of powder comes with a spoon that has the same dimensions of the opening of the bidon… Powder everywhere, every time. Very…
This is a simple 18mm dia, 14mm bore and 3mm deep non drive side spacer for Tacx Neo 2 trainer to better suit 142mm through axle bikes. This will thread on to the standard non drive side adapter for the Neo and replaces the 6mm standard…
Befestigungsersatzteil für oberes befwegliches Teil. Es wird zusätzlich einen Sechskantschraube benötigt (M5)
Makes for a bigger platform to put stuff. just glued the top onto the base. I did split the base up to save filament I printed in petg, but tpu and adding fuzzy skin could be cool.
2 replacement parts for the T3000 cyclestand: The main support for the downtube to clamp the bikeframe to. Then there is a file for the arms to hold the front wheel in place, to prevent the handlebars from bumping into the frame.
No support required, pretty simple print. Use two of the base pieces to fill out at the bottom and provide better support. My iPad has a case on it, which meant it didn't fit with the standard mount. Shove a couple of the base pieces in…
The box was printed in PLA with 15% infill. It's not a tight fit on the trainer, just use some rubber strips if you want to have it fit tighter. Additional items required: 2 x M5x35 mm countersunk screws 2 x M5 inserts 8 x 5x2mm magnets
Cycling For my Tacx Vortex I designed and printed a Phone Holder which can be attached by means of clip on (no screws needed) for mounting on the Tacx. This one has a depthe of 10.5 mm and a width of 77 mm (Samsung A52). If you need a…
I was inspired by a nipple-remover for Bontrager bottles, but as my bottles have been manufactured by Tacx, so I designed a compatible one. Usage instructions (cf. the photos): 1. Press down the nipple 2. Position the tool so that its…
Makes for a bigger platform to put stuff. just glued the top onto the base. I did split the base up to save filament I printed in petg, but tpu and adding fuzzy skin could be cool.
This adapter wasn't buyable so I created it myself. Tolerance: 0.3mm Print it with something strong like ABS or CF20.
Upgrade your indoor training setup with this 5-part rocker plate set, designed specifically for Tacx trainers (see compatibility). These printed feet provide greater flexibility, comfort, and effective vibration damping. Features: * 5…
