Counting matching models…
Add a practical hanging point to the back of the seat and make better use of the luggage compartment. This 3D-printable fold-out hook provides a convenient place to hang lightweight everyday items such as shopping bags, small accessories…
Umbrella holder for the trunk. Two hooks are needed that hook into the top tether mounting points. I think it should be printed with PETG, ABS or other heat resistant material, because the trunk can get hot in the summer.
A) NOTICES (herunterscrollen für deutsche Version / scroll down for German language version) Non-commercial provision of construction files in .3mf-format and in .step format for a tether strap holder for my cycling computer type Wahoo…
This is a slightly modified from OEM tether that uses the original vehicle components. Other models I have found were slightly mis-sized, or just a little too short for the recessed cap on my VW T5 transporter. Note for some models, the…
A secure base for Anker 555 USB-C Hub (8-in-1) ( https://a.co/d/06YljEZ8 ) to TetherTools AeroTrac Table ( https://tethertools.com/product/aerotrac-workstation-system/ ). Utilized TetherTools 3D Makers kit (…
Many VAG vehicles (including Skoda) use a small rubber tether to hold the fuel cap when refueling. This part tends to break very quickly over time due to aging and constant bending. Unfortunately, the tether is not available as a separate…
You have seen the training aids that are designed to help you control your arms through your swing. The ball is designed to be printed in TPU so that you can gently squeeze it between your forearms. The teather attachments can be printed…
Popis (Description) SK: Praktické riešenie pre majiteľov vozidiel Dacia Sandero Stepway s továrenským pohonom na LPG. Originálne krytky plniaceho hrdla často chýbajú alebo nedržia. Tento 3D tlačený set obsahuje odolnú krytku a flexibilné…
Modeled this directly off of the remains of my gas cap tether that finally snapped after 18 years of use. A cheap stiff yet flexible TPU seemed to work almost perfectly.
Cricket stand with pod holder and a tether that should be printed out of TPU
This is a simple model to protect the USB connection of the camera when shooting tethered. It was designed to fit under a D850 body and hold an orange TetherTools cable by friction. A tripod screw (I used a Manfrotto one) is needed. When…
Remix of a small plug with a tether to keep it at hand on my drybox. Intended for TPU printing.
A bumper/tether for a Twelve South AirFly Pro Bluetooth Wireless Audio Transmitter/ Receiver so that you don't leave it behind when leaving the airplane. (I'm totally not speaking from experience here. That would be silly). A simple…
A quick, easy, tether for your Airpods 3/4/Pro/Pro 2's! This is a simpler, more utilitarian version of my " "Wired" Airpods with USB-C and Audio Jack " , which is intended for running, as airpods can easily slip out of your ear,…
A simple tether for Chilly's 500ml water bottles. Print in TPU and stretch over neck of bottle. It should be pretty durable. Prints flat with no supports required. A great test print for TPU.
Anchor your holiday spirit with the Tree Tether – A sturdy, Christmas tree-shaped ground stake designed to securely fix your decorations in place. Perfect for keeping your festive displays merry and bright, even in the windiest winter…
Background I use a bunch of different action cameras for capturing mountain biking, motorcycle, and dirt bike riding footage, and I always try to use a tether to ensure that I don't lose a camera if a mount were to fail on me. I've bought…
This is one of three options I've made available for Bowden PTFE Coupler C-Clip for the Adventurer (AD5M) Runout Sensor. Kudos & thanks to Vance Howard for the suggestion. OPTION 3 of 3 — TETHER to TUBE edition — Prints in TPU. Easier to…
I wanted to carry an extra battery on the front of my backpack using Peak Design's Anchor Connectors or Think Tank Red Whip bungee straps. The Red Whips are really tight, but they do work. I used Inferno3D's (on MakerWorld) remix to remix…
Replica for original part (skoda number 57A 867 785 9B9) I used 50% fill. Print from: PLA Support: Yes
Gridfinity organizer for the Bosch GLM165-40 with a slot to hold the tether
Quick and easy print. I used NinjaTek Cheetah TPU which does a great job gripping the rubber cap with a nice tight friction fit. However, TPU is a tad bit sticky and the lower ring has slightly more friction when closing the lid causing…
My air tools dont have caps on them, and if they do, they're just plugs; easy to lose. Not anymore! Male and Female for EURO couplers Print in TPU 100% infill. (i used Bambulab TPU 95A) Tethers should be able to stretch over the couplers…
Made a super simple hook for fastening the wire to the handle on the remote of my Fifish V6s. You should be able to fold the wire tight enough to feed it trough the hole and over the “bollard". leave it in place on the wire and use it…
Add a convenient tether point to the top or side of a YakAttack BlackPak or ShortStak. I keep fish grips, pliers, line cutters, and other small tools tethered to my kayak. Traditional milk crates provide plenty of places to clip them, but…
Add a convenient tether point to the top or side of a YakAttack BlackPak or ShortStak. I keep fish grips, pliers, line cutters, and other small tools tethered to my kayak. Traditional milk crates provide plenty of places to clip them, but…
With this setup I plan on never misplacing the stylus and having to re-print it, or worse yet, dropping it and then idiot-kicking it way up under the workbench as I frantically try and retrieve it. I printed the holder in PLA with default…
A Reconstruction of a Broken clip from the original part + pictures. Printed in PETG 0.12 layer height.
Umbrella holder for the trunk. Two hooks are needed that hook into the top tether mounting points. I think it should be printed with PETG, ABS or other heat resistant material, because the trunk can get hot in the summer.
This replaces the OEM gas gap strap. You will need to carefully remove the retention ring from the cap that secures it and a 5mm snap rivet holds it in place. The latter is very difficult to remove without breaking. I may upload a remix…
I'm not sure if many people operate SeaBotix ROVs any more, but I figured I might as well post this just in case anyone else has lost or broken their original tether handle! This is a crank handle to allow the tether reel to be easily…
A pool thermometer I purchased, and INKBIRD wireless pool thermometer, had a really small attachment point for tethering to the sidewall of the pool, and if left free roaming, it would always go out of range of the wifi gateway, and…
I was looking for a Binder 712 Untethered Socket Cover to go on the back of may AiM Dash and they were all like $12 so I made one you can download a print. Depending on your printers abilities I have only with just the inner threads and…
When I go skiing, I always am nervous pulling my phone out on the chairlift, worrying that even though I'm gripping it as hard as I possibly can… a bump on the ride is going to cause me to drop it. If I had even the slightest sense of…
Replacement for Genuine Toyota Fuel Tank Cap 77300-07020. This was for my 2012 Toyota Prius, but I believe it also fits Avalon and Camry models of the same model years. I printed this in TPU with 10 walls (100% infill). Tip for easier…
A measuring sound specifically designed for tetherspouts. Its flat shape you to determine the vertical (no larger than) and horizontal (no smaller than) numbers for the retainer. Handles measurements between 8 – 17 mm. Each millimeter…
By request on my other model (XT90 flexible cap & tether) - here's a flexible version designed for the balance port. I started with the model uploaded by RapidMonster and recreated it so I could tweak the design and add the tail with the…
Dzielę się tym dla przyszłych pokoleń, długo szukałem czegoś takiego i w końcu znalazłem, więc oczywiście zamieszczam link do oryginału poniżej :)
From Tether Tools Labs, the Phase One IQ4 Adapter for Tether Tools TetherPro Optima Cables is a secure precision fit for the digital back’s USB-C port. Once the adapter is printed, take your Optima tether cable and locate the end with the…
You can mod it to any other use, or to fit better in your car. Mine is Ford Kuga/Escape, but it is standardized interface, so it should fit in a lot of others. Just one note: slicer defaults to hiding the seam inside the hook, which is…
Small thin model that provides an attachment point for your phone. Insert between the back of your phone and the phone case. Best printed from TPU or other flexible filament.
What the Tether Keeper (TK) does : Prevents the tether loop around the tree from loosening when tether is no longer taut. How it works : Friction fit onto the vertical component of the tether that acts as a stopper for the tether thru…
I grew tired of losing body clips after a roll over and I knew these tethers already existed, but I didn't know where to buy them. Therefore, I made my own using TPU filament. Simply make a small hole in the body of the RC that you want…
This is a simple panel mount for anderson power poles. It includes a gasket/template and tethered dust cap. Print the gasket in PLA to use as a template for cutting the holes for the panel mount. Then print the gasket and dust cap in TPU…
This simple design gives you a place to easily connect a wind tether. Made from TPU it's strong, absorbs shock and holds up to the weather. If you make it out of something else, it may not be strong enough.
This is a replacement cable holder for the Valve Index. It replaces the left side cable retention if yours is broken off. I had several goals with this repair: 1. Trap the cable stopper so that it won't slide out either direction 2. Avoid…
A cap cover + tether for the Mazama x Miranda Goes Outside M!GO Bottle since there's no official one yet. Fully removable, but you could glue the cover onto the cap if you wanted. It fits perfectly over the cap and TPU has enough flex and…
The Garmin Varia (eg RTL515 ) is a wonderful series of bicycle radars, but it lacks a tether for positive backup attachment. This mount lets one add a tether -- such as a spare Garmin-branded one -- and secure the unit to the bicycle so…
I have these inexpensive (you can get them for sub $5 each sometimes on Ali Express) Tuya Zigbee water leak sensors anywhere water could potentially leak inside the house or in the garage. Fishing them back out of places like under the…
A) NOTICES (herunterscrollen für deutsche Version / scroll down for German language version) Non-commercial provision of construction files in .3mf-format and in .step format for a tether strap holder for my cycling computer type Wahoo…
Simple fix for losing your remote! It has the added benefit that while fitted it prevents the battery compartment opening. I've printed it in PLA,CF ASA and TPU all printed fine without support. It's a tight push-fit with rigid filament.…
This is technically a remix, but after finding several issues with the original model, I rebuilt it from scratch. The concept is solid, but the execution needed improvement. This version corrects the screw sizing to match the #10 screws…
This is a slightly modified from OEM tether that uses the original vehicle components. Other models I have found were slightly mis-sized, or just a little too short for the recessed cap on my VW T5 transporter. Note for some models, the…
The cap doesn't stay put in the included hole so I made this. I printed in TPU. There are couple of versions and several ways you can connect them
I wanted to have a custom SSD holder for when I use my AeroTrac table. Printables AeroTrac Base ( https://www.printables.com/model/1406318-aerotrac-workstation-system-track-base ) Printed with PETG, 3 walls, 25% infill. Print vertical…
A secure base for Anker 555 USB-C Hub (8-in-1) ( https://a.co/d/06YljEZ8 ) to TetherTools AeroTrac Table ( https://tethertools.com/product/aerotrac-workstation-system/ ). Utilized TetherTools 3D Makers kit (…
Many VAG vehicles (including Skoda) use a small rubber tether to hold the fuel cap when refueling. This part tends to break very quickly over time due to aging and constant bending. Unfortunately, the tether is not available as a separate…
You have seen the training aids that are designed to help you control your arms through your swing. The ball is designed to be printed in TPU so that you can gently squeeze it between your forearms. The teather attachments can be printed…
Popis (Description) SK: Praktické riešenie pre majiteľov vozidiel Dacia Sandero Stepway s továrenským pohonom na LPG. Originálne krytky plniaceho hrdla často chýbajú alebo nedržia. Tento 3D tlačený set obsahuje odolnú krytku a flexibilné…
Isofix Top-Tether connector for double-sided Velcro
Stop losing your hot knife cap! Print the tether in TPU Insert the knife from the bottom into one loop, then slide it up. Insert the cap from the top into the other loop. I included my TPU profile for Polyflex TPU 95, but it should work…
Keep your glass mouthpiece attached to your puffco pivot! Print in TPU (TPU 95 profile in downloads) Insert pivot chamber into large loop. Stretch small loop around mouthpiece. I included my TPU profile for Polyflex TPU 95, but it should…
I spent over 1200 hours in the design, development, and build of this "Untethered ROV". Now you can reap the benefits! Please watch the video. I will add more info here in the coming days. This is a very well-rounded project for people…
Modern Tethered Airship Concept This is an original concept model of a tethered dirigible (airship) designed for high-altitude wind energy generation. The airship stays in the air and uses wind to produce electricity, which is transmitted…
This is a hook that can be connected to the top tether mount. It fits well in my nx4 Hyundai tucson. There are 2 parts to the connector: a mount that clips on to the top tether rod and an accessory that holds whatever you want to secure…
I recommend using TPU for this with a hardness of 98A or higher (TPU for AMS). Print in the orientation as supplied in the .3MF file for strength 0.20mm layer height 2 walls 15% infill Arachne walls supports required
This is a functional replacement part for a broken or worn-out original fuel cap tether. It is designed to restore the factory functionality and keep your fuel cap securely attached to the vehicle. I have personally tested this design on…
This is a simple, low-profile cable support system designed to fix the notorious extruder cable sag on the Prusa MK3S. Instead of heavy printed arms, this design utilizes the natural flexibility and springiness of a standard 1.75mm…
This is an improved version of my previous fan bracket, that is tethered. The story: My original metal fan bracket bent, so I made the 3D printed replacement. That eventually broke (when the extruder hit a blob, or something), and then…
The tether that keeps me from losing the fuel cap on my Mercedes Benz Sprinter dried up and finally broke. As I have been known to leave fuel caps on the vehicle after fueling and drive off, I decided I better come up with a replacement.…
I created this tether mount after a high-impulse flight destroyed one of my Mini TXes at liftoff by inertially pulling the board off the Kevlar tether I had looped through the PCB holes. Clearly, that was not the way to fly and I needed…
I had issues with my car's parcel shelf popping out from its mounts completely through daily use. I've designed these extra tethers to keep the shelf in its mount even if it comes loose. Print in any heat-resistant material, like PETG,…
Tethered caps for sharp needle type multimeter probes. Print Settings Printer: Artillery Sidewinder X1 Rafts: No Supports: No Resolution: 0.12mm Infill: 100% Filament: Any TPU Any Category: Electronics
This is a mod to Rat Rig's V-Minion 180 printer to remove the separate electronics box and make the printer a single unit. Electronics box is designed to take boards compatible with Ender 3 board - SKR E3 V2 in my particular case. The…
Simple 2" hitch cover design with tether. Print in TPU with at least 3 walls and 20% infill for stiffness. Print Settings Printer: BLV mgn Cube Rafts: No Supports: No Infill: 20% Filament: Inland TPU Category: Automotive
Gas Cap Tether for 2012 Audi A6. Should work with other car models too. Part Number on the gas cap is 3C0 20 553L. You must print in TPU or another flexible filament! PLA or ABS are too rigid for this purpose and will snap. Print Settings…
A pen holder designed to mimic the pens on bank counters that are attached to the base with a chain. Designed for use with Bic Cristal pen and either twine or an elastic band as the tether, but the FreeCAD file is included in case you…
May require scaling depending on the size of your umbrella or the straps on your bag. I made this to fit a Bunnings Gold umbrella.
A simple TPU replacement gas tether for Honda Civic Type S 2009.
This is a replacement gas cap tether I designed for my 2011 Subaru WRX. It may work on your car if the OD of your cap fits into the ID of the tether (68mm) . Best results likely with TPU, but I have not tried other materials.
My original tether broke after 13 years so i designed a new gas cap tether for Mercedes Vito W639 If you need help how to print this message me Print instructions Printer brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
Instructions I printed my case at .2mm layer height with 15% infill and it works well. Make sure to align the center piece's flat face with the build plate as I have not yet figured out Fusion360 well enough to change this by default. The…
I bought a used Volvo C30 and saw that it didn't have the OEM gas cap. I didn't like the fact that it didn't have a tether (and didn't want to hold it or place on the roof), so I made a tether to hold it in a similar fashion to the OEM…
Hi, This model is designed to secure a fire tv remote to a wall, it comes in two parts, one secured to the wall and the other secured to the back of the remote using double sided tape. there is a tether between the two, made from a…
This is a set of parts to turn a Tecnec Jackreel 4 ( Also known as a Shill GT310 reel in the U.K.) into a full featured ROV tether interface using the Blue robotics Fathom line of tether extenders. It should fit a Fathom S or X board, I…
To build one of these, you will need a Schill Gt380 http://www.markertek.com/product/schill-gt380/schill-gt380-19x11-plastic-rubberized-cable-reel . They are not inexpensive. You will also probably want the optional solid lid plate and…
I got tired of my ribbon cable dragging across my bed and prints so I made a cable clamp and top fixture to suspend it. I just added a piece of shock-cord with beads both ends as toggles. The clamp is a tight fit and needs supports on the…
I wanted a smoothly rolling pulley for my ubmillical… so now I have one. I modeled this to use an old belt pulley wheel from the tronxy x5s that I have since torn down. Print 2, supports will be needed. Use an m5x24 bolt with a nylon lock…
I got a tetherball for my dog for play. It works great and he loves it! The problem I encountered was that when he'd get the tetherball rope wrapped around the pole (which is obviously the goal when you're actually PLAYING tetherball), he…
This is a remix, adjusted and optimized for TetherPRO cable and Nikon Z6 Mark II
I love my YakAttack BlackPak Pro kayak crate, but wanted to be able to mount the included TetherTube fishing rod holders at an angle other then vertical. YakAttack sells an add-on ($20 USD each as of this publishing) that allows an…
![[Option 3 of 3] Flashforge Adventurer (AD5M) Runout Sensor - Bowden PTFE Coupler C-Clip with TETHER to TUBE feature](https://media.printables.com/media/prints/1137299/images/8582387_34919d77-614a-4166-a1b6-7a278797404e_ab9cab1c-6335-4b55-8dc6-2d7b80fe8b9b/2025-01-06-ad5m-bowden-ptfe-coupler-c-clip-option-3-of-3-printables-thumbnail.jpg)
