Counting matching models…
Update 04.01.2024: I noticed a few mistakes, most importantly the screw size for the front tunnel, which is M3x12mm and not M3x10. I did some changes to the model because I noticed I was measuring the height at the wrong place. While I…
Print approx. €0.99–€1.21 excl. taxPreliminary estimate for one variant
A simple bracket for the Netgear GS108E . It has small holes so you can see the power LED and retain access to the factory reset button. It fits very snugly and you'll have to relocate the rubber pads slightly (or you can remove them…
Print approx. €2.25–€2.75 excl. taxPreliminary estimate for one variant
This is a remix of the design https://www.thingiverse.com/thing:1322695 . I seperated the model and added some support, so you can print it also on smaller printers and you are more flexible to mount. You have to mirror the parts in your…
Print approx. €1.31–€1.61 excl. taxPreliminary estimate for one variant
This is a wall mount for a SiliconDust HDHomeRun Flex 4K ATSC 3.0 NextGen TV tuner. Included are the associated Fusion 360 source .fd3 , .3mf, .stl, and G-Code (PTEG 15%, infill) files. Photo shows the top of the case facing out. However,…
Print approx. €4.61–€5.63 excl. taxPreliminary estimate for PETGSource material: PET
Rack mount ears for Netgear GS108E switch. Remember to hold switch while pluging cables to prevent it from moving to the back. I've added a hole on each ear for the switch feets. Inspired by: https://www.thingiverse.com/thing:249851 Print…
Print approx. €4.12–€5.04 excl. taxPreliminary estimate for PETGSource material: PET
This is a Pegboard mount for a Netgear GS108T switch. It has a 75mm spacing between the mounting holes and uses a standard 1"X1"X1/4" U.S. peg Board. Pictures are from version 1. Version 2 has the holes to reduce some of the plastic.…
Print approx. €3.73–€4.55 excl. taxPreliminary estimate for PETGSource material: PET
The tolerances are a bit tight so you might need to sand it down a bit.
Print approx. €2.21–€2.71 excl. taxPreliminary estimate for one variant
I rewired my wired network and needed to mount the newly installed network switch in an entertainment panel. There are two versions of the holder but they're 99% the same. The one for the panel mount has bumps in the back to match the…
Print approx. €7.39–€9.03 excl. taxPreliminary estimate for one variant
Wall Mount for Netgear Switch – Secure and Space-Saving Solution Organize your network setup with this custom-designed wall mount for Netgear switches. Built for stability and ease of use, this mount is the perfect solution to securely…
Print approx. €0.19–€0.24 excl. taxPreliminary estimate for one variant
Komplette Seifenhalterung Konstruktion Seitenwand wird 2 mal benötigt bei einzelnem Drucken.
Print approx. €16.39–€20.03 excl. taxPreliminary estimate for one variant
A replacement interior cover for the MAN TGX truck, replicating the original MAN part (…-0459). It measures 186 × 62 × 21 mm and has 4 spring clips with latches on the long sides and 4 hooks on the short sides, so it snaps into place like…
Print approx. €3.07–€3.75 excl. taxPreliminary estimate for PETGSource material: PET
Oni Cyber Punk Mask by SeanAranda From Thingiverse. Posted here due to Thingiverse losing popularity and Creator being MIA for over a year. I have also added the remixed version that is preassembled. A brilliant design i wanted to share…
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the 10inch_TP-Link_SG108.stl by https://www.printables.com/@mariusbach_1431080 since the TPLink SG108 is roughly the same size as the Netgear Switch. Printed…
3D printed rackmount enclosure for the GS308EP (should also work for GS308EPP model)
A wall mount for the Nighthawk M6 Pro. Has a cutout so you can plug in power, Ethernet and antenna connections. Print with the back facing towards the build plate and with supports. For supports that are painless to remove, use these…
Very nice satisfying hexagon fitget. Easy to print. Printed from PLA. For assemble you need 4 magnets.
This is a 10" rack mount for a Netgear ProSafe GS108Ev3 network switch. This model assumes you have the 4 round stock rubber feet under the switch. Printed in PLA with a 0.4mm nozzle using 0.2mm SPEED preset with adaptive cubic infill.…
The switch can be mounted under a table, on the wall or wherever you can fit 2 screws in it If you are looking for the same holder for the 8 port switch: https://www.thingiverse.com/thing:3278568 Print instructions Category: Computer…
A pair of brackets to mount a Netgear GS110TP POE-switch into a 10"-rack. As the switch is a little wider than the mountig rails in a 10-inch-rack, the switch is actually mounted behind the rails with a little gap to accomodate the cage…
I didn't want to spend $40USD per mount for the netgear wall brackets so I made my own. I printed in prusament PETG with a .6mm nozzle using draft fast settings in prusa slicer. They are beefy as the routers/satelites are quite heavy. YOU…
A 10" Rack Mount for the NETGEAR GS308E Managed Switch . Features The sides include a honeycomb structure for better airflow. Two small screws can be mounted on the floor part which will hold GS308E in place. Printing The print takes a…
Switch dimensions: 94mm width 26mm height without the feet mounting holes: 6.5mm diameter 35mm center distance
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
For mounting a Netgear Nighthawk M1 on the wall. Update 2023-03-02: Version 2 has some nicer fillets and don't hide the feet that can be removed to access the connections for the external antennas
Frontgewicht zum Anstecken an Bruder Traktoren.
This is rack mount tabs for a Netgear GS316 series switch. The rear bracket uses M3 screws to replace the existing screws in the back of the switch.
I needed to rework and mount as much of my networking gear as i could which necessitated removing the modem's stand and constructing a wall mounted solution. The most important goal for me was to make the simplest print i could while not…
Great for most NETGEAR switches, 5 port, 8 port and 16 port… Not tried anything bigger. Probably works with other brands too.
Wall mount (invisible screws) for Netgear Switch GS308T
10" rack mount for Netgear ProSAFE Gigabit switch GS108 (maybe others). It has one kestone slot on each side of the switch. Designed to fit my 10" 2020 rack. When inserthing the switch the sides will need to flex out a bit in the rear,…
This is a case for the Netgear Nighthawk M1, M5 and M6 that can be placed on a table or mounted on a wall. To mount it on the wall, a wall bracket is attached and the case with the device is slid into it. This allows the device to be…
Brackets for mounting a Netgear GS108 switch to the Multiboard mounting system. You will need to print 4xHandsOnKatie_Standard-Underware-Connector from the original remix file library.
OpenSourceEV Parts designs, produces, and shares 3D‑printed parts for Rivian EVs. Staying true to our open‑source mission, every product we create comes with free STL files so anyone can remix, customize, or print at home for little to no…
This is an Easy to Print Small Holder for the Netgear GS105 Lan Switch I was Searching for a Similar Model in the Web but didn't Find anything (maybe I searched not good enough) well whatever, I decided to just make my own, the Result You…
Official german traffic signs from 274-5 (5 km/h) up to 274-130 (130 km/h) in original size of 600 mm. You'll need a multicolor capable printer or use different element heights with filament change in between. At least 3 colors. The mf3…
Hello together, I needed a fixation bracket to mount my netgear switch under my printer enclosure. Happy printing :)
Originally model was prepared for GS305EP switch, but considering size of other GS equipment, it should accommodate most of them. Model has tolerances, so switch does not have to be forced into it. End plate requires M2 screws, holes are…
Über den Parameter “Spalt” kann der Freiraum für den Switch verändert werden. In der ersten Veröffentlichten Version stand er auf 0,2 mm, jetzt ist er 0,5 mm und liefert etwas mehr Freiraum.
This bracket holds a Netgear GS308 Ethernet switch to the underside of a shelf. Uses four wood screws to attach. Print instructions I used PETG. PLA would probably work too. Print settings are not critical -- it didn't need support or…
Mountingbracket for Netgear switch GS305 or GS308 with a height of 29mm
Requirements: M4 x 10 screw * 2 M4 Threaded insert * 2 (optional)
Sollte der Router zu eng in der Halterung sitzen ändern Sie den Parameter “Spalt”. Zur Zeit steht er auf 0,3 mm. Mit 0,4 oder 0,5 sollte der Router leicht in die Halterung ein- und ausführbar sein. Meine Halterung ist im Wohnmobil…
Needed a way to mount two GS308E Netgear switches onto a wall on top of each other to conserve space so designed these wall mounts that fit around the switches. I have left room below the switches to pass cables, and left gaps between the…
This is a remix of the design https://www.thingiverse.com/thing:1322695 . For a smoother fit I made it 1mm bigger in the inside and added a honeycomb pattern to it. The switch can be mounted under a table, on the wall or wherever you can…
I liked Rehtori's Netgear Orbi Wall Stand, but wanted mine a little smaller and closer to the wall. I made an open grid on the bottom to maintain ventilation. Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament:…
I found various examples of mounts for this switch but all were bulky, used a ton of filament, or didn't use the factory mounting holes. I had one of the original metal ears that came with the switch and used it to model these. The result…
10" server rack for Netgear GS305 5 port switch. Pretty simple design, I printed face down using mouse ears.
Allows you to fix and hide a network switch under the desktop or a shelf. This one has been designed for a Netgear GS108 switch but it should work with other netgear devices with same dimensions. Printed with 0.6 nozzle with orange…
i made a rack mount for my cm1000 modem, it mounts right now with zip ties in my case but you could probably stick it on with vhb tape as well. i just made it simple and didn't want it to be complicated with multiple parts. also the…
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the design from @BrianBerkley. Printed face down, 2 versions are available to be used with/without M3 metallic threaded inserts. 2 screws M3x10 are required…
I needed a decent wall mount for a Netgear Orbi so came up with this. Printed in Prusament Signal White PET-G it holds the router nicely and there is room at the back to feed the cables through the slot in the base. Print Settings…
Support to be able to hang Netgear Switch 8 port Unmanaged Gs308 stand. Print height 0.2 also it is recommended to add custom print supports for the hooks behind.
Super simple and compact tazer module. Parts i used: High voltage module: https://s.click.aliexpress.com/e/_dSZnwyn Lithium charging board: https://s.click.aliexpress.com/e/_dXTpFtH (Without the over current/overcharging protection) I…
Mount for the Netgear MR1100
This is a rack mount kit for the Netgear GS108 switch designed for a 10-inch rack. The kit comprises three parts that can be 3D printed without the need of support. The clamps must be secured to the main part using two small screws. I…
Adapterplatte zum Tausch einer Schuko-Einbaudose gegen eine Kaltgerätebuchse. Passt zb. für DMX Kabeltrommeln usw… Lochabstand: 38×38
Dear makers, we would like to share our DIN holder for switch NETGEAR or MikroTik Routers.GS308E. Consist of left and right holder. Overall depth ater installation is 81mm from DIN rail. Compatibility: NETGEAR (26 mm thickness): GS308E…
OpenSourceEV Parts designs, produces, and shares 3D‑printed parts for Rivian EVs. Staying true to our open‑source mission, every product we create comes with free STL files so anyone can remix, customize, or print at home for little to no…
Auflagekeil grade und 7° für Feinwerkbau Luftgewehre links auf anfrage auch rechts usw.. mit schraubbarer Klemme M6 Support wedge straight and 7° for Feinwerkbau airguns on the left, on request also on the right, etc.. with screwable…
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
Material: nGen Ich habe hier ein günstiges (ca. 60€ Stand 2023) Ablagestativ für Luftgewehre entworfen und gedruckt. Außerdem braucht man: 1x Stativ für einen Baustrahler (Durchmesser= 25,4 mm) 3x M6 Muttern 3x M6x20 mm Sterngriff (länger…
Schlüsselbrett für Oldtimerliebhaber von Eicher
Ich habe hier einen Adapter konstruiert für das Zusatzgewicht von dem Claas Disco 8550 C Plus Mähwerk. Eigtl ist dieses Gewicht für den kleinen Claas jaguar 900. Im Internet werden diese teilweise kostenlos verschenkt. Das Gewicht passt…
It was designed to attach to the underside of a desk. There are lugs that fit the bottom screw holes of the switch. It also has hooks to clip in the cables to keep it somewhat tidy. If you have a 200x200 build plate like me then rotate it…
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
You can fix it with double adhesive face or 2 screws Printer settings : Material : PLA Infill : 20% Support : no
The Netgear MR 1100 hotspot gets hot very easily, and shuts down. This Cooling case is designed to keep it cool even when under heavy load. A small 40mm noctua fan is attached to the bottom of the case and is powered by the USB A output…
It's a DIN-rail mount for th GS305v3 from Netgear
The print in the picture was a misprint, but it still worked, so I kept it.
Wanted to mount this guy to a board, did not like the goofy stand it came with. This would possibly work with other versions of this model.
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
This mount has especially been made for the NETGEAR Nighthawk M6 Pro (MR6450) Router. Just mount it to any vertical surface and let the router slide in from above. It has a double rear wall with ventilation holes for thermal convection.…
I wanted to move my switch off of the shelf to make it easier to access, so I designed an under shelf mount. It prints fine without supports if you print it with the back downwards. I've included CAD files if you want to remix it.
This item is a small wall mount for the Netgear gs105 LAN switch. It is designed for the using of tesa powerstrips for the wall montage. It can be used for vertical and horizontal mount. Print Settings Rafts: No Supports: No Resolution:…
I found that most 3D printing 19 inch server rack holder designs for Netgear GS316EPP and GS316EP 16 Port Switches were either too large for my heated bed (23.5 x 23.5cm) or had too much unused space . So I decided to make one of my own,…
This mount holds the Netgear GS305E switch in a 10" rack. You have to slightly force the switch into the mount. This is deliberate for the switch to stay in place even when yanking the cables. The switch is mounted assymetrically, I've…
Remix from 6 inch rack to 10 inch rack
Got my Netgear CM2000 Cable Modem, and for some reason it seems Netgear wanted it to look "sexy", which means it has a bunch of weird angles, and takes up a bunch of unnecessary space. I found a mount (…
Since the wall mounts I found with a quick search didn't really appeal to me, I developed my own version. The wall mount consists of 2 parts that are screwed by means of M3 screws and threaded inserts. The switch is tightly enclosed by…
The pegs can be used to adapt the 40mm spacing to the 45mm of a Netgear GS105, or any other device with that pattern. In “reverse” order, the pegs can provide a 35mm width pattern. The holes are 3.5mm to be tapped M4 and the tolerances…
Here is the STL and the Fusion file incase you need to make any modifications to it. I printed in PLA at 20% infill. The screw holes on the side of the switch are M3. I used 8 total M3x8 screws and 4 #6 wood screws to mount to the bench.…
This is a wall mount bracket for the Netgear Nighthawk M5 (M5100/M5200) I could only find M1 and M2 brackets and none were suitable for my needs. Designed this in Tinkercad. M5 slips in the back into the pocket, then the rear spacer slips…
Simple vertical stand for a Netgear Network Switch.
Here is a print that will fit diagonally on a Creality K1c. I printed it in PETG This design will mount an 8 port Netgear switch in a 10" mini rack for my raspberry Pi's. There are ventilation holes which also aid in reducing the amount…
Ringkorne von 3,8-4,2 mm, 0,5 mm hoch, am Besten zu drucken in 0,1 mm Schichtstärke. Passen in die gängigen M18 Korntunnel bspw. von Walther oder Anschütz.
Downloaded a mount and hated the print so I designed my own. Fits like a glove. If your printer isn't finely tuned, I'd probably experiment with 101-102% scale printing. I just printed it at 2 shells and 10% infill using Prusament PLA…
You need: 1 of each of the 4 models 4x M3 heat set inserts 4x short M3 countersunk screws 4x countersunk screws for your preferred wall mount solution Print the outside brackets with the outside on the build plate, so no support is…
About this model: This has been modeled for the Netgear Nighthawk M6 (MR6110) It is a simple snap fit outer case, made from PLA, PETG, or whatever filament you like. There is an inner “sleeve” designed for TPU. I mimicked basic phone case…
Theres the STL and the Ondsel file, i printed it at 100% and it worked ok, Only change i made after print was add a 1mm fillet on the recepticle to make it stronger but its manly aesthetic. Use a Brim, the side where there is no holes…
This is 19" 1U rack mount bracket for a Netgear 8-port Network Switch (GS308PP). It's pretty beefy because it will be in a portable case and need to stand up to a lot of rough handling. I printed this with PLA on a Bambu Labs A1 Mini, so…
Some Rack Ears for the Netgear GS110EMX Network Switch to mount in a 10“ Rack. Two Variant are available to mount. The normal 1U Variant and the weird 0.5U Version. In my Case it worked perfectly but it may not in yours… I would suggest…
Uses Leviton push pegs to mount in the box, then slide your switch on the pegs. Pegs are 80mm on center, with 6mm posts
Beware this is only the right side of the modular rack model. Make sure you know this before printing. Use supports (organic is better)
An improved mount that prints in one piece and will securely contain a Netgear GS308E switch. Uses set screws. Will continue to add parts and pictures as I build my rack. Print face down with supports enabled. Four m3 screws are required,…
I'm continuing to modify my NextGen enclosure, so it works for the space and setup I have. The TPU helps with the seal and vibrations for the fan. If you don't have TPU, you can try skipping those parts, but I recommend adding them. R2…
Not much to say about this Thing :-) It's dead easy to print, use 4 Wall_Layers, infill 20%, no support if printed rear side to plate. As always: I added Autodesk Fusion file + Step - modify as you like. Print Settings Printer Brand:…
I love my Netgear Orbi setup (powerfull router + satellite), but was a bit disapointed that it was so difficult to put in a wall. I have built rj-45 sockets high in the wall for a good router placement, so hanging it into the wall was a…
Ein Thermostatgehäuse für das STC-1000 Modul. Das Gehäuse besteht aus 2 teilen, der Boden und das Gehäuse selbst, das Gehäuse wird einfach auf den Boden aufgesteckt. Im hinteren teil befinden sich 3 Löcher (2x12.1mm 1x 5mm (Sensor) Beide…
I prefer to keep my switches off the shelves and add them to a standard 19" server rack instead. I recently picked up this GS305P and adapted a rackmount adapter for it. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x…
![Netgear Switch Wall-Mount [GS308, S350 Series]](https://media.printables.com/media/prints/460635/images/3783683_5042795b-299b-464b-890b-50ccf43c28fc/img_20230423_134931.jpg)
