Counting matching models…
The original file that I remixed is this , I have added new features to test. I added new things to test like stringing test and the write on the bottom. You can also test a lot of other things: bridging bed level stringing calibration…
Activate firmware retraction in your slicer. Activate firmware retraction in klipper by adding this to you printer.cfg : [firmware_retraction] retract_length: 0.8 retract_speed: 60 unretract_extra_length: 0 unretract_speed: 60 Slice the…
Add these decorative traction boards to your Traxxas TRX4 rig for some instant credibility. Look great printed in orange, but could be really cool in red too.
My sprinklers were all very overgrown with grass so I made a 3" hole saw to help clear out the area. You put a 1/4-20 bolt in the center and use a nut to hold it in place. It does a good job of breaking up hard dirt and grass around the…
They are super easy to clip on and remove from the spring-loaded sliders inside the CFS lid. One is with SUNLU written on the top, other one without text. EDIT: Because of someone commenting 5mm is better than 6mm I added a 5mm version.…
Baby Vaccination Aid – Pain Distraction Device This 3D-printed device is designed to help reduce the discomfort babies feel during vaccination. By providing a gentle sensory distraction, it helps mask the pain of the needle, making the…
Vrstva 0,16mm, 45% výplně, materiál ASA. 6mm vratový šroub, pružina, podložka a křídlová matice. _______ Layer 0.16mm, 45% infill, ASA material. 6mm gate bolt, spring, washer and wing nut.
An unusual chip extraction attachment - screwed underneath, to the foot, for edge work. Typical top extraction (i.e. between the milling machine and the foot, pulling the chips upwards) do not remove the spoil well when working with a…
This is my take on a simple and effective retraction test model, designed to help you fine-tune your 3D printer's settings. Recommended Print Settings: Layer Height: 0.2 mm Infill: 0% Walls: 2 Material: Tested with PLA, but PETG should…
This is a model are based off of a Halo-gravity traction (HGT) device created at Ann & Robert H Lurie Children's Hospital of Chicago. It's intended use is for medical education and fostering medical play opportunities. The model is scaled…
Simple Easy to Print Solder Fume Extraction for 120mm fan Print uprights with no supports. Carbon filter can be added using additional housing between the fan and extractor.
Simple connector, might need a spacerbetween it and the wall
What is Hextraction? Tile description and rules: These two tiles can trigger any roll-through effect tile. The Trigger Tile works only on adjacent effect tiles while the Board Trigger Tile covers all effect tiles on the game board. Now,…
Simple Easy to Print Solder Fume Extraction for 80mm fan Print uprights with no supports. Carbon filter can be added using additional housing between the fan and extractor.
I am very grateful to the author of this detail for the simplicity of solving the problem of coiling plastic with an empty coil. Here is the original model:…
This Snowboard Stomp Pad is a 3D-printable traction pad designed to improve grip and control when riding with one foot unstrapped. It helps keep your boot securely in place while skating, getting off the lift, or riding flat sections. The…
TL;DR This is a variant of a Flip-Flop tile for the 3D-printed board game Hextraction . The main feature is that it can be rotated, so it can be used on the whole board Print recommendation: Nozzle : 0.4mm Layer height : 0.2mm Perimeters…
This vent is mounted in a blanking plate in a window opening to typically exhaust fumes from a 3D printer and interfaces to a 120mm fan or duct. 2 design variants are included Thread insert version 4mm thread, 4mm deep 3.3 mm hole for…
a model designed to fit over CDs to give more traction when making science Olympiad projects or just projects.
Since DeWalt doesn't have an affordable drill dust shroud I made one myself. It works with DeWalt vacuums, but an ordinary one would still be fine. The cutout for the drill is 30x30mm. For lower power vacuums you need to make the cutout…
Welcome to the Space Silo Space Silo is an original, 3D-printable tabletop game designed for zero-waste printing and high-stakes fun. Perfect for family game night or as a STEM counting tool! The Mission Extract modular fuel cores…
Compatibility: Any 120mm fan with 105mm mounting hole spacing should fit. I'm using a Noctua NF-F12 industrialPPC-3000 PWM, but you're not locked into that. The fan mounts to the baseplate using two thick self-tapping screws that cut…
This adapter allows you to connect the FANZWORK extraction hood for angle grinders with the Bosch Click & Clean system. The adapter is eccentrically positioned to provide as much space as possible for your fingers when gripping. Printed…
The adapters from the exraction systems are usually too short. This adapter acts as a connector. Dimensions: Thicker part: 62 mm Thinner part: 57.5 mm Length: 80 mm Print with 100% filling Just print and have fun! Check my other posts…
An adapter to connect a shopvac with a 45mm OD hose to the generic 90L desktop sandblasting cabniets. I have tested on a Pollor brand cabniet but when I ordered this one there are lots of other brands selling what looks to be the same…
If your filament is not retracting properly (the spool doesn’t rotate) and instead unwinds inside the Qidi Box instead of going back onto the spool — this model fixes that problem. This spacer reduces excessive pressure between the…
Introducing DINO DICE board/dice game for kids When playing with FlexiDinos with my kids, I wanted to make a small board/dice game for my kids to have fun learning addition and subtraction (totally not preparing them for playing DnD with…
This is a linking piece needed to make the board wider, assuming a standard height (or slightly taller) board. Works with all Hextraction boards.
Inspired by the original Festool jig. Unfortunately, the tool is not available for the Festo OF 1000, so I redesigned it. If the cap is difficult to turn, a drop of oil helps. Inspiriert von der originalen Festool-Vorrichtung. Leider ist…
This Model is a free-form designed Fun Fair attraction that is known under a lot of names, like “Crazy Dance”. It can be easily printed on most 3D printers (biggest part is <20cm wide) and has only one part that requires support. Since I…
I would like to thank Akasilentcreed for this design. Happy printing
I love the original idea, and the main design of the lamp, but I improved the look. For the best look two filament changes are recommended. (The photos show the tile printed scaled down to 80%, since my whole Hextraction set is 80% scaled…
This frame and spacer ring set allows you to put some additional fans to help pull hot air out of a computer with top mounted radiator. Any 120mm fans should work, but its designed for AC Infinity AXIAL LS1238. 360mm is larger than the…
A parametric retraction tower that can be used to determine the optimal retraction distance with many travel lengths.
I designed this off the original Mimaki printer fitting. I included additional screw holes to help allow to angle the fitting a bit more to accomodate my extraction system. It's my first design, and probably will need a tweak, but all the…
Disclaimer If you are not confident with tackling mains powered projects seek professional advice. I am not liable for any issues that may arise from incompetent or unauthorized wiring practices! Fan The fan was purchased from Aliexpress…
My Dad asked me to make an extraction Box which he could use to extract fumes whilst soldering. Box Dimensions: Length 120mm Width 50mm Height 23mm (25mm With lid) Spout is 30mm in length and 43mm in diameter (outside) 40mm (inside) Can…
This is a revised design of my original to better accomodate a 100mm ID PVC pipe fitting. I also revised the vertical attachments from the base to the elbow. This is designed to accomodate my other design of a “T” piece with 100mm PVC…
This T Piece junction will accomodate a 100mm ID PVC pipe. It is designed to be used in conjunction with my other design of a 90 degree elbow and fit 100mm ID PVC pipe and/or a 100mm flexible hose. The other design is here:…
I've printed the adapter for the jigsaw in TPU because it's flexible. Print settings: - 4 layers bottom - 4 layers top - Nozzle: 0,4mm - Layer height: 0.2mm -Infill: 25% Concentric Please download the model, print it and give me a like.
When replacing rear brake pads on newer Honda Accords or Civics with electronic parking brakes (EPB), the EPB must be retracted before compressing the caliper piston. If you don't have a OBD2 scan tool capable of retracting the EPB via a…
Changing the genuine adapter of the saw with a new one that fits a Parkside vacuum cleaner hose (35 mm)
A set of 4 dice, 2 dice with numbers, and 2 with symbols. Use whatever dice work for the skills being practiced. 2.5 hour print
LEGO Citroën Traction This is a model compatible with the LEGO system. Just print it, attach a LEGO chassis, and you're ready to play. Very easy, very simple.
Add these decorative traction boards to your Traxxas TRX4 rig for some instant credibility. Look great printed in orange, but could be really cool in red too.
I bought the Jrready Molex Microfit tools for working on ma Voron printer. I liked the idea to create a case like kyleisah did. But his case is a little to tall in my opinion. I think that is because of the minimum height of the rugged…
This custom cover transforms a standard PC fan into a useful tool for soldering by directing the airflow to absorb fumes
ip çekme aparatı rope pulling device جهاز سحب الحبل Seilzuggerät dispositif de traction de corde
It is made for the common DN 50 Tube System. You need a seal for the side where the tube comes in.
I designed these to be printed very quickly so you can test your retraction settings without wasting a lot of time/filament.
I needed specific angled connector pieces for my in-house mechanical ventilation. Since the original parts were made from ABS, I decided to design and print the pieces; I have made a variation of adapter pieces (please visit my account)…
I needed specific angled connector pieces for my in-house mechanical ventilation. Since the original parts were made from ABS, I decided to design and print the pieces; I have made a variation of adapter pieces (please visit my account)…
I needed specific angled connector pieces for my in-house mechanical ventilation. Since the original parts were made from ABS, I decided to design and print the pieces; I have made a variation of adapter pieces (please visit my account)…
no supports needed for any thing if you wnat to print a spacer then you sould print multipul so that it comes out better. you may need to shrink or enlarge the tile so it fits on your game board.
My sprinklers were all very overgrown with grass so I made a 3" hole saw to help clear out the area. You put a 1/4-20 bolt in the center and use a nut to hold it in place. It does a good job of breaking up hard dirt and grass around the…
This custom-designed tool slide integrates a Dewalt Trim Router Plunge Base with a Festool track, allowing for precise and adjustable cuts along the track’s length. This design is perfect for cutting custom-width grooves by adjusting the…
I have a Wanhao i3+ (with Microswiss hotend) which, let's face it, is a positively geriatric printer at this point. It's always struggled with getting clean seams on certain prints after a move, no matter how much or how little retraction…
A fume extraction spacer for an AnyCubic Photon Mono X2. The rectangle design is designed to use this round to rectangular elbow. For the full fume extractor, I have this setup in this order: Elbow Elbow to 120mm Fan Adapter Arctic P12…
Introducing the Dicey Destroyer Tile! When the trigger gets activated, roll a six-sided die and destroy the tile adjacent to the number that was rolled. If the space that was next to the number is empty, destroy the dicey destroyer tile…
diameter : first circle:3mm second circle: 5mm square:4x4mm and last random shapes separated by 2mm the whole is 80x20x41mm (without a base 40mm)
Original Model Description by Zach Freedman When nothing remains, everything is equally possible. Dump your hand with this simple utility tile for Hextraction, the hackable, 3D printable board game. I developed this as an example of a…
Credits: First I have to give credits to Ifixit for the idea of the fume extraxtion device. They made a tutorial and listed up all the components you need and how to wire them. So check their article if you want another explanation…
This is a 20x20x20 mm calibration cube designed to test your 3D printer's accuracy and optimize print settings. The cube includes features for measuring dimensional precision and analyzing filament retraction. Perfect for fine-tuning your…
Print this remixed 5.1" elbow adapter, then everything from the original model excluding the original elbow: QIDI Q1 Pro Exhaust Duct and Fume Extraction Port With 90 Degree 3" Swivel Elbow
They are super easy to clip on and remove from the spring-loaded sliders inside the CFS lid. One is with SUNLU written on the top, other one without text. EDIT: Because of someone commenting 5mm is better than 6mm I added a 5mm version.…
This model is compatible with the lego system.
Fixes Creality CFS retraction issues with small spools that can't reach the bumpers on top of the CFS lid. It's a more comfortable solution to spool rings. Comes in 2 variants with different sizes from 1mm to 10mm. The size is the…
This is a tool which can be pressed or gently pounded into a 1.5" IPS bath / shower drain to facilitate removal if you don't have a tub drain removal wrench tool or if the legs to which a standard tool attaches are rusted through, broken,…
This is just a basic spacer to fit the steering knuckles on the Cragsman. The spacers are used when running a high steer setup (Steering tie-rod on top of the knuckles for better ground clearance). 2 spacers are required per vehicle/ one…
I made this rear skid plate/ servo guard to replace the rear bumper bar on my Cragsman in order to gain a better departure angle and help protect the rear diff lock servo. It also has a small lip to help prevent the lower edge of the body…
A simple socket to remove and install the wheel centre caps on a Traction Hobby Cragsman. Easily remove the centre caps by hand. Requires no additional tools. Printed upright with no supports or raft/brim. -If the tool is firm on the…
I made this offroad tow hitch to tow a camper trailer behind my Cragsman. Designed to accept a Traxxas TRX-4 rod end. The lower side of the hitch has a hex opening to hold a plain M3 nut, and the pin is an M3 screw through an M3 wing nut.…
I replaced the stock ESC in my Cragsman with a Holmes BR-Mini ESC, so I designed this retaining clip to hold the wires in place against the battery tray. It also has a small tab to hold the receiver lead plug in place. You will need to…
Model pro Retraction Stress Test je skvělým nástrojem pro optimalizaci nastavení retrakce na 3D tiskárně. Umožňuje snadno identifikovat problémy, jako jsou stringing (vlásečnice) nebo nedokonalosti při přechodu mezi tištěnými částmi. Díky…
PARKSIDE Router POF 1200 D3 Replacement for the original dust extraction adapter. Printing information The STL file ist correctly aligned. Layer height: 0.20 Perimeter: 3 Infill: 25% Support: none Brim: recommended I am looking forward to…
Sign reading: “WARNING THIS SIGN IS A DISTRACTION" It's perfect to divert the attention of your visitors, wanted or unwanted. you don't really need a multi color system, just insert a pause command ca .75mm from the top layer and change…
Converts original high pressure low volume foot to high volume low pressure on 100mm extraction hose. Fits to original pneumatic actuators. Aluminum reinforcement plates to take the load off the 3d print.
A fast retraction test that also tests your printer's overhang up to 75°! This is a useful calibration test tool that uses less than 2g of filament! Feedback and Makes are always appreciated, If you're up for another challenge, check out…
Bonjour, Voici mon test de rétraction simple mais efficace et rapide ! Pensez à vous abonner à mon compte pour être au courant de mes nouveaux objets ! Si vous trouvez ça utile et que vous aimez mon travail, vous pouvez me remercier avec…
Clip-on dust extraction for Festool MFT/3 Multifunction Table with holes for 4x workbench dogs pin storage. It simply slides in the table rail and holds the special air suction from the dust extraction nozzle where you need it allowing…
Making the model solid, it only took about 1.5 meters of filament, great test to be able to run out some scrap filament shorts you might have laying around!
Enjoy this quick and easy print and test your printers capabilities. I made this test with time and wastage in mind after revisiting an old model I uploaded back in 2017. (https://www.thingiverse.com/thing:2563909) The models are as…
Played around and made the model, really quick fun print to test the perimeters of different filament/part cooling fans. 0.2mm layer height, increase model size to 120% if the slicer struggles to slice the walls of the tubes.
Una simple señal de advertencia A simple warning sign
They make great pedals but the tractions pads are not that great. They tend to crack and falling apart in a year or two.
I needed something that would allow quick release of the traction boards without spending a fortune on mounts. I mounted long M8 bolts to the back of the van. I used 100mm bolts which was perfect for amazon special traction boards. Put…
Necesitaba esta llanta CaDa, cuando empezamos a fabricarla nos faltaba para construir nuestra grúa. @Alguien podría necesitarla. @Les dejo el archivo de Solidworks para que puedan hacer las modificaciones y ajustes. I needed this CaDa…
THIS IS NOT A DISTRACTION. But the sign is. How I Designed This I saw a sticker, and said Hmmm and made a sign. Sign beats Sticker.
Converted Lid to accept 5x2mm magnets to keep closed
What came first?: Trigger Chicken - Place a chicken on one of the shooting ramps blocking its access. If a chicken has already been created, you may change the posistion. Trigger Egg - Roll an additional egg ball for your turn. Printing :…
Baby Vaccination Aid – Pain Distraction Device This 3D-printed device is designed to help reduce the discomfort babies feel during vaccination. By providing a gentle sensory distraction, it helps mask the pain of the needle, making the…
This model is compatible with the lego system.
This is an adapter to connect a regular Henry vacuum cleaner to the dust extraction of an Inca bandsaw with a ~53mm port. Mine is a 1980s “Euro 260” model, but I assume they all have the same port. v4 is the original version and which I…
Like me, if you dont have time, or just not enough filament, just use the smaller Temptowers. Based on the "All in One Temperature & Bridging Tower - PLA & PETG GCode included" from Tronnic, and the remix “Prusa Mini Temptower for PLA,…
