Counting matching models…
I would recommend ABS or ASA, as the part is exposed to direct sunlight and therefore heat. layerheight: 0.2mm infill: 20% (gyroid) wall loops: 4 top shell layers: 5 (cause we need a little bit extra material for sanding)
Changed the windshield rim/frame, bottom side is 3mm wider and top side is original width or change as you like (provided step file).
Windshield side winglets can give a bit an optimised stream of air since the BT1100 windshield is somehow narrow at the top. These are specifically done for 4.5 mm-thick windshield that is curved in two directions. There are three size to…
This model is a housing for the Whelen LIN3 emergency lights and its designed for an F150 and uses double sided tape to stick to the upper portion of the windshield. There is minimal flashback inside the cab and uses a 35 degree angle to…
General This is a replacement for the original Puig CS1 Mini Windshield mounting bracket. Compared to the original, the new bracket has a deeper slot so you can mount the windshield lower on your headlight. The original had a very big gap…
This is a robust 2 part clamp to replace the stock windshield mount on 2017 Can-Am Commander. 2 @ M5 x 20mm screws required, I used stainless
I made this simple teepee to prevent your windshield wiper blades from freezing to your windshield without standing your wiper up vertically. I've always hated the idea of standing your windshield wipers up vertically when it snows, I…
3 models are included below: The windshield itself. The attached black portion of the windshield covers the wiring for the dashboard. The rubber grommet required for assembly in case you lose the original ones for some reason? print in…
Purpose: For securely mounting the Valentine V1 Gen 2 radar detector onto the windhsield of S550 Mustangs, without the unreliability of suction cups. I am personally not a fan of suction cups, so I created this. Uses the standard mounting…
This 3D printable car windshield ice scraper is designed to be compact, lightweight, and easy to carry, making it ideal for winter driving conditions. The scraper features a triangular shape that offers a comfortable grip and effective…
A roll cage style bar that sits inside of the lexan of the windshield on the Axial Scx10.3 CJ7. descrete and provides ample protection to keep your widnshield form getting caught on rocks and ripped off. made because my friend and i have…
Volvo v70 facelift windshield trim clips. Please use V4 as i found that the previous design was too thin and snapped easily Simple clips to hold the trim/moulding that covers the drip rails on either side of the windshield Printed in PETG…
Slicer: Cura Material: PETG (CRON) 🔧 Nozzle & Layer - Nozzle Diameter: 0.4 mm - Layer Height: 0.16 mm - Initial Layer Height: 0.16 mm 🌡 Temperatures - Nozzle Temperature: 235 °C - Bed Temperature: 80 °C 🚀 Speeds - Print Speed: 32.5 mm/s -…
After I took off the parking clock off my windshield to change the battery easier, I wanted to mount it back but so I could take it off in the future again. So here is my solution - it holds it with a *click* in without shaking or making…
This is a plug you can print to replace your missing Miata windshield wiper arm bolt cover (they tend to get lost). Print in TPU for best results. You can also print a set in a custom color to match your car. Enjoy...
Premium Windshield Mount for QJMotor 125SRV (2025 Model) Designed with precision and passion, this custom-engineered windshield mount is the perfect upgrade for your QJMotor 125SRV 2025. Built specifically for this model, it ensures a…
Winter Windshield Wedge Ice & Snow Scraper Tool with Storage The Winter Windshield Wedge is a compact, multi-function winter tool designed for fast, efficient ice removal and everyday cold-weather convenience. Its triangular wedge body…
Card-Edge Ice Scraper The Card-Edge Ice Scraper is a compact, functional winter tool designed to turn an everyday credit card or gift card into an effective windshield ice scraper. Inspired by planer- and razor-style tools, the card is…
Scanned the profile and then converted to svg then added the protrusion that engages the trim. Modeled after the clips used on the later Nissan 300zx Z31s
The pin can be made out of petg or abs, but the bushing needs to be made out of tpu
For storing a camper van windshield cover. I made this for use on a Van Essential overhead shelf in a Ford Transit.
Clips to support windshield washer lines on factory hood. Using small 4.5mm holes between the typical clip locations for extra support of windshield washer lines. Printed with 0.20mm layer height and 4 perimeters in PETG.
Clamp on Windshield Phone Holder for MGB or MG Midget NOTE: PRINT THE GoPro VERSION. It's just better. Also, I completely re-invented this mount from the ground up and that version is available here . I needed a special mount to secure my…
We lost our windshield wiper fluid cap. I designed and vase-mode printed a new cap that should pop over the top of the fill tube. The fit was pretty tight. I set the extrusion width to .8mm in the vase mode print and had it print 1mm of…
What you see here is a set of windshield wipers with a license plate carrier meant for Trx TRX-4M Defender. These just clip onto the windshield frame. With this design there are more nails hit - wipers are 1 model, easier to print and…
I had a broken hinge on my original cap and decided to try and print a new one rather than buy. I searched a few sites for an STL, and couldn't find one that would fit the Veloster. But, I came across Wischwasserbehälterspritzkappe Ford…
I would recommend ABS or ASA, as the part is exposed to direct sunlight and therefore heat. layerheight: 0.2mm infill: 20% (gyroid) wall loops: 4 top shell layers: 5 (cause we need a little bit extra material for sanding)
This is a simple cap covering the nut holding the windshield wiper arm in my Volvo. It may fit as well for other brands, where the nut/wrench size is 15mm. I designed it based on the remains of the original Volvo cap, with slight…
A gasket for the bolts used on mainly sport motorcycle windshields. I wasted so much time searching for the rubber gasket that I forgot I had TPU. Whipped this up and works like a charm on my motorcycle. Printed using PLA profile without…
This is a Golfcart Windsheild stop to prevent the windshield moving up the frame when driving Category: Vehicles
Car Windshield Ice Scraper with a Secret Joint Stash Compartment Winter is coming, and so is Christmas, so I designed this as a unique gift for a friend who is a pothead :D and also owns a car in a place where temperatures drop below…
This is a remix of Tyco Trucking US-1 Windshield And Lights from RockChalk846. I have an older truck without the windshield. It does not have headlights or clearance lights, so I removed them from the model. It only has the windshield and…
modern cars have long dashes and very angled windshield. its very hard to clean the inside of the window. i made this simple tool to easily reach and be able to throughtly clean my windshield! you can even wrap a lint-free towel or even…
Introduction Refilling windshield washer fluid can sometimes be a mess, but not anymore! This funnel is designed to be used when refilling windshield washer fluid with minimum waste of washer fluid. Features Handle: This funnel has a…
I have a Ford Focus 2012 (Hatchback) and after 5 years of prolong heat the windshield wiper tank cap decided to disintegrate. I whipped this up it Fusion 360 and printed it in PETG. This cap may fit newer ford(s) vehicles. Print…
🏍 Revolutionize your riding experience with our meticulously crafted 3D-printed windshield, tailor-made for your CB650R. Engineered to perfection, this innovative accessory offers a seamless blend of style, functionality, and…
Changed the windshield rim/frame, bottom side is 3mm wider and top side is original width or change as you like (provided step file).
Print with some strong settings. I printed this with 3 perimeters, 50% infill, PETG, 0.6 nozzle. I printed it on its side (as seen in the picture and also add some supports to help keep it on the bed). When I used it, the plastic bent a…
Phone number on windshield, my version - simple, universal, easy… use waterproof marker to make Your number :-)
Om dat de gewone ruiten wisser om de ramen langs buiten te ontdoen van regendruppels en dauw te lang zijn voor de kleine ruitjes en autospiegels. Heb ik zelf iets ontworpen met 2 lengtes 10cm en 18cm. Het handvat is van PLA en de rubbers…
Print the whiper in the given orientation. After printing, you need to brush the tip of the whiper with a smal lighter flame in order to make it soft. Bend it 90° to fit on the Armadillo
This is my updated version of the windshiel fluid funnel, modified for those who are dealing with a tighter fit.
funnel for ford focus 2 (windshield washer fluid) or other with hole bigger than 32mm. Printed with PLA (use brim, no supports)
can be left next to car battery for everyday use. it fits in my octavia 3 Brim is nessesary!
Claas Targo K70 windshield curtain mount. Print on the side, with eyelet up. ASA for UV resistance.
This is a grommet used to attach the rear of a mid or large windshield to a Ski Doo Summit Gen 4 snowmobile. After removing the beauty panel, place this grommet in the larger holes left behind, and then press-fit the windshield. Print…
This is a simple windshield ice scraper with a rounded edge. Car windshields usually are rounded meaning a straight edged scraper does not work well when scraping frost from the inside of the windshield. This scraper has a slightly…
Designed a small part to hold the windshield wiper up from getting stuck to the windshield with light snow or ice
Ice scraper for car windshield with replaced blades. Print new blades as many as you want! Once the old blade wears out, there is no need to re-print the entire scraper, just print the blade only! For free available basic blade.…
Lejek do płynu od spryskiwaczy (pasuje do Orlen i inne) - średnica 29 mm, Windshield washer fluid funnel, Nálevka kapaliny ostřikovače čelního skla Moje ustawienia wydruku: Materiał PLA, warstwa 0,3 mm, wypełnienie 15% lub więcej, podpory…
Details: Designed to fit UVEX ski helmets perfectly, ensuring a secure hold for the windshield. Easy to print and mount – ideal for use on the slopes. Print Settings: Material: PETG has proven to work best. Infill: 100% for maximum…
For better strength and watertightness, use the following settings: Walls: 3 Layer height: 0.3mm Line width: 1mm (0.8mm should work for most hotends if 1mm is too much) Wall generator: Classic (Arachne doesn’t work well with this model)…
You can print this with 13.5g of filament. Great scraper i use it for my windshield.
This is windshield washer water tank cap for Hyundai Getz and Accent Era. The sample photos were taken on a 2010 Hyundai Getz. I changed the size and the connection part for easy opening and closing of a generic model I downloaded months…
If you want to make a transparent windshield from a plastic bottle or transparent sheet, print the pdf and use it as a template to cut out windshield. You will have to scale down - hood_light_black on z-axis, and hood_light_yellow on x or…
For windshield wipers with attached spray nozzles. Tested on a Citroen Aircross C5, should fit other models. This is a replacement clip that attaches the water line to the wiper frame. Printing in ASA recommended. Works OK with PETG.
This AlumaCraft Windshield Mount is a strong and reliable replacement for broken or missing mounts on AlumaCraft boats. Designed with marine-grade durability in mind , it offers: ✅ Secure fit – Designed for a precise and stable connection…
Print with TPU !!!! If you lost your fluid cap just print it :)
Mine broke when i yanked the blade against the windshield in attempt to break off ice. Without that cap blade is falling apart, so i've made the replacement
The clips that hold the windshield to the side by side Canam Commander 800 are not sold separately from the windshield (at least i did not find any). so I reversed it from the broken part. Included the 3MF, the Fusion 360 file, the stl…
This is a windshield washer fluid cap for a 2011 Cadillac CTS. The cap may fit other Cadillac years and models.
This is new windshield trim for the honda del sol, it's not a recreation of the original but a completely new design that eliminates the stupid plastic clips that always break and utilizes built in channels to lock into the factory metal…
This is a model for the hood hinge/ windshield cowl boot for the Honda civic EG and Del Sol. It has a superb fitment and I modeled a little channel on the bottom to install with no glue needed! Just slip it into place and you're done.…
This is a model of the specialty trim clip for Honda del sol (and maybe other models) that holds the windshield cowl gasket and cowl on. Print in either PETG or TPU. PLA might work but it will likely break so I recommend stronger more…
Cap for the windshield wiper water reservoir for a Toyota Avensis from 2002. Printed it in TPU 98A
ULIMATE Print Bed Scraper/Windshield scraper wide and narrow versions! print at 0.16mm layers or less for best edge. Don't forget to- like share print and follow!
This is the little rubber boot that protects the wiper pivot from taking on water. I printed it in tpu. No supports required.
I designed this for my F10 M5 and Escort Max360c radar detector, but I'm sure it will work on other makes and models along with most current Escort detectors. This allows you to tuck the detector up close to the roof right between the…
Windshield side winglets can give a bit an optimised stream of air since the BT1100 windshield is somehow narrow at the top. These are specifically done for 4.5 mm-thick windshield that is curved in two directions. There are three size to…
Unfortunately, the Dacia Duster doesn't have an ideal solution for accessing the windshield washer reservoir. When refilling the fluid, a significant amount often spills out and goes to waste. Therefore, I modelled a simple funnel to make…
Sometimes, you are not satisfied with just a single wiper blade over your windshield, sometimes you're wondering why some trucks has double wiper blade on a single arm, does it even do anything? Now you can try having 2 wiper wiper blades…
I made this to mount the control unit of my Yaesu FTM-400XDR to the windshield of my ford E-series van above the mirror. It is meant to angle the head unit about 10° down and 10° towards the driver of LHD vans for an optimal viewing and…
Cap for tesla model3 windshield fluid tank.
Replacement's were expensive and I didn't quite trust existing models on our bumpy roads so I modeled a beefier solution. Print Material TPU is highly recommended but not required. If using a rigid filament, you'll need to slide the…
Windshield Washer Fluid Cap - With and without print-in-place hinged lanyard. Example in photo was printed using PETG 100% infill without support or brim to fit 1998 Nissan Frontier. (2.25 inch)
Description: The Windshield Wiper Blade Tester is a tool designed to check for fractures in rubber wiper blades. By wiping the tool along the blade, users can determine if the blade is broken; the tool will detach if a fracture is…
Windshield funnel made for my 2021 - model 3, wanted something way easier to pour into. the OD of the base of the shaft is 38mm and the funnel max diameter is 125mm I recommend printing in petg funnel down on the build plate with no…
Windshield/flyscreen for Husqvarna Svartpilen 401. Maybe also would fit vitpilen. It mounts using stock speedometer bolts. Also it would need 4 M5 bolts/nuts to mount the flyscreen to the brackets. I was able to print it on Ender3 with…
Simple washing fluid nozzle for Subaru Imprezza and probably others Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: ANY ASA PC Category: Other
Clip for weather/rubber trim on A-pillar for Seat Leon MK1 (1M) / Toledo
This model is for anyone looking for replacement window caps, on their boat. I recommend that this model is printed in a highly temperature resistant material, to prevent warping or melting as the boat can become incredibly hot. I…
787 cockpit windshield wall decoration Included alignment guide for easy setup Easily scalable size in slicer
This model is a housing for the Whelen LIN3 emergency lights and its designed for an F150 and uses double sided tape to stick to the upper portion of the windshield. There is minimal flashback inside the cab and uses a 35 degree angle to…
Set top and bottom shell layers to zero and walls to four. Set the infill to thirty and the infill pattern to Honeycomb or whatever your preference is. It has a snug fit to help keep it in.
This is just a simple remake of the official support. One of mine melted due to extreme heatwave and the second one broke on a bump. Decided to design them in Fusion360. I made them a bit thicker. 5mm instead of the default 3mm. Added a…
I wanted to test the effect of a windshield on my motorcycle but found the longer ones to not really match the design of the bike. I know a longer windshield probably works better but I wanted to get a middle ground between looks and…
This is an improvement of my windshield washer lid https://www.printables.com/model/839835-peugeot-traveller-screen-wash-lid-deckel-fur-wisch. This one has a retaining strap and can be printed with 2 colours.
A replacement for a cheap motorcycle windshield extender 10º C over the recommended max temp for PLA, from 220 to 23010º C over the recommended max temp for PLA, from 220 to 230
Matchbox Superfast MB1 Dodge Challenger. I had a broken windshield so I made a new one.slight modifications might be needed depending on the resin/printer used. This is a basic windshield, I didn't add the "rear view" or "wipers" to it,…
This is a windshield scraper I made. It's designed to snap together, but I had to use a little bit of heat to soften the plastic before it actually snapped into place. The reason it's designed to snap together is so that a cloth pouch can…
Windshield GPS mount with vent for the Goldwing GL1800 or GL1500. For the model purchased at this link: https://www.temu.com/pl/goods.html?_bg_fs=1&goods_id=601101577114426
It works, printed with TPU 85A, 15% infill. Less infill, softer it is.
