1,677 models
+3 Magazine Extensions for 9 x 19 Glock 17 OEM Magazines. Additional Hardware Required: M3 Threaded Inserts DIN 912 M3 x 6mm Hex Socket Head Screw or equivalent Soldering iron or long M3 Screw + heat source Sharp knife or Dremel…
The magazine base plates will fit original Glock 2-row magazines in “normal size” calibers: 9x19mm, .40 S&W, .357 SIG etc. e.g. for the Glock 17/34/21… I recommend to print them standing upright with a brim and set the slicer to finish…
This is ECI mag block for a Ruger 10/22. Keeps the bolt from closing.
Small magazine loader, which will save you some pain from loading. Use your thumb to press it down and up like this: I recommend printing this with a glue stick applied to your printing area. Gcode has a 2cm of skirt added because I…
Print approx. €1.38–€1.68 excl. taxPreliminary estimate for one variant
I based my design to incorporate the 3 different dimensional variations. So some will fit tighter than others. Some versions of the magazine have different thicknesses and angles which cause them to sit differently and more of an angle.…
The source marked this model as adult content.
Print approx. €0.55–€0.68 excl. taxPreliminary estimate for one variant
Spy Vs Spy : Mad Magazine
10.11.22 I added a .3mf file. This files shows how I reinforced the area around the screw to increase its strength and integration to the model's body. This is a remix of air_ 's AR 15 Magazine rack. It uses these magnets to attach the…
Print approx. €11.06–€13.51 excl. taxPreliminary estimate for one variant
Hello, Welcome to my profile, full of models and miniatures :-) I have Airsoft magazine feet for Glock and AAP pistols for you. It is suitable for faster magazine changes in pistols and fits beautifully in the hand. It is both aesthetic…
Print approx. €2.05–€2.50 excl. taxPreliminary estimate for one variant
I designed 3 mounting options of my magazine holder for the Umarex Gauntlet. These mag holders mount to standard picatinny rails. They are two part prints that are held together to the rail by a standard M4 bolt. The hole for the bolt is…
Helps to drill properly-spaced holes (0.531" on center) in the floor plate of a 1911 magazine, for mounting a base pad (such as my own 1911 Pistol Magazine Base Pad .) Printing Details I printed in PLA. The hole on the front side can be…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for one variant
Description: Hey fellow Nerf enthusiasts! Are you tired of your Nerf blasters with magazines cluttering up your shelves and desperately in need of an organized storage solution? Look no further! Introducing the Free 3D Printable Magazine…
Speedloader for the 32 acp and 380 acp magazines for the Keltec P32 and P3AT. Slide it over the top of the magazine, press it all the way down, place a round, let up on the speedloader, then slide the round all the way back. Repeat. Print…
Print approx. €1.18–€1.44 excl. taxPreliminary estimate for one variant
Shoe on a pistol magazine. Botka na zásobník M9 pro pistoli Beretta 92 SB Compact. Vymezuje mezeru mezi zásobníkem a pistolí. Zásobník M9 je příliš dlouhý a tak trčí ven. Toto to maskuje přidělává se na zásobník pouhým nasunutím . Print…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA HATCHBOX BLACK Transmission Distance: 1 PLA YEETIN GRAY Transmission Distance: 2 PLA YEETIN BROWN Transmission Distance: 5.2 PLA YEETIN…
Print approx. €5.56–€6.80 excl. taxPreliminary estimate for one variant
Speedloader for the 9mm magazine for the Keltec PF9. Slide it over the top of the magazine, press it all the way down, place a round, let up on the speedloader, then slide the round all the way back. Repeat. Print it upright with a 10mm…
A tool to ease the loading of Beretta Bobcat 20X .22LR magazines. It comes in two variants, one with wings and one without. The wings variant allows for easier unloading and improved one-handed operation. The no wings variant is more…
I have an old no-name M4-style softgun which uses non-standard rear-feeding STANAG-style magazines, which are very hard to obtain today. As some of the interal parts of my original magazine has cracked over time, I decided to…
Print approx. €3.58–€4.37 excl. taxPreliminary estimate for PETGSource material: PET
The stock limiter that comes with the RIA VR60/VR80 9rd shotgun magazine is designed to only allow 9 shotgun shells maximum. However, if you reduce the size of that limiter you can actually squeeze a 10th shell in the magazine. So I give…
Print approx. €0.62–€0.76 excl. taxPreliminary estimate for PETGSource material: PET
Magazine Rack Maximum Height. As tall as a Prusa MK4 can print. Remix of https://www.printables.com/model/594904-magazin
Purpose is to transport airsoft replica magazine separate from the gun, just like you would do with a real deal. It does not make much difference safety-wise with an airsoft replica. Yet, the purpose of owning airsoft replica is to train…
**************** If you download 💾 or collect 🗄 please hit the LIKE 👍 button. 😀 If you print 🖨 it post a picture 📷 / MAKE ! 😄 Let me know how it works for you.❔ 🙂 Don't forget you earn Prusameters🧵 when you post a MAKE ! ****************…
If you travel by commercial airline with spare lithium batteries, not only must they be carried in your carry-on only, but you also must protect them from damage and short circuit. This regulation is part of (in the U.S.) 49 CFR §…
Print approx. €3.52–€4.30 excl. taxPreliminary estimate for one variant
31.12.2024 Version 3 is now available! It features an 8-round magazine, stronger spring, easier printing of bridges, stronger lever! Check it out here: https://makerworld.com/en/models/934485#profileId-899040 Version 2.0 is released!…
The Breacher is a 3d printed Nerf tube-magazine shotgun blaster that fires and ejects Silly Shells! It's spring powered, with a pump action prime. Yes, it actually fires multiple darts at once! READ THE "Print Info" SECTION of this…
Spring Gun V2 - Shoots fake bullets with magazine Spring gun v2 can fire multiple bullets one at a time thanks to the new magazine system. Reading the comments and advice from users, I designed version 2 of the spring gun. The new version…
Dummy magazines for safely practicing dry-drills etc. They lock in normally on the mag catch and don't activate the slide release/hold-open. G17, G19 and extended versions. Should fit all generations. 05.08.2025 Update: Taken down due to…
This is a 3d printable AK magazine speed loader for AK magazines in 7,62 and 5,45. It was inspired by the podavach U-Loader with the goal to make it 3d printable on a standard 3d printer. It gives you the ability to load AK mags at least…
READ INSTRUCTIONS: I see a lot of the prints and you guys area printing it in the wrong orientation. It's much stronger if you print it with the Holder orientated how it would be when you use it. UPDATE: Added Glock 43x Needed a place to…
This tool will allow you to quickly make correctly sized springs for AR-15 magazines and is adjustable to allow for various types of wire. This project is heavily inspired by HW Enterprises’s SpringFactory. Included is a PDF guide, STLs…
PMAG Style AR 22lr Magazine 25rd Top is easily replaceable in case of damage. I included 2 styles of followers. The standard one which is the style my older Black Dog machine mags have. Follower 2 is similar to the CMMG follower and will…
Not my model, share it via makerworld.com from SD Studios. printed with Nebula PETG on Prusa i3 MK3S
AAA battery holder in magazine style, functioning springfed holder that fits +/- 10 AAA batteries. Link to AA version: https://www.thingiverse.com/thing:5463356 SCALING If you have problems with scaling using .STL files, scaling to 1000%…
Nerf full length elite dart magazine. With a printed spring. Feature a symmetrical design so you can insert it both ways. Compatible with most blasters (tested on Spectrum, Stryfe, Turbine and Echo). Printing the magazine Print body,…
Available versions: for 1-2-3-4-5 mag, real and airsoft with screw and perforated panel mount. The mounting holes are designed for 4mm countersunk screws.
Talon/half-length nerf magazine designed to be vertically printed in record time. Faster to print, more modular design, more compatibility, more customizability! Print this with 1 wall with a good PLA+ filament and it'll be a strong,…
Improved version for faster prints, only needs supports for the center plunger. 17/L,19/x,26,34,45 also works with P320/P229
the spring is recomended to print on PETG, mag bott 2 is of a tighter fit, on my print it just snapped right in without any glue needed
Držák na 6 kusu zásobníku pro AR-15. Pro Mid-cap i Hi-cap zásobníku. 6 piece magazine holder for AR-15. For Mid-cap and Hi-cap magazines.
Glock 9mm double stack magazine speed loader - 2 Versions. One has more rounded sides on the top end. I printed these with 100% infill and they are very sturdy. These have less slack around the magazine than some of the other models I…
Printing Instructions Print without supports and at 100% infill. If using PrusaSlicer, I recommend disabling “Thick bridges” and enabling “Detect bridging perimeters”. If you have assembly issues with the holes being too small, you can…
!!!!!!!!!!!!!!!!!!!!! This has only been tested in my particular frankenstein AR9. Functionality and safety in any other firearm cannot be guaranteed. If you damage your firearm or yourself, that's a you-problem. !!!!!!!!!!!!!!!!!!!!! v2b…
This is a remix of the magazine holder by moorefoodnow . It uses a heavy duty magnet to attach to your safe. The magnets are found on Amazon . Fully charged magazines are easily held in place with these magnets. Meant for Gen 2 PMags but…
AA battery holder in magazine style, functioning springfed holder that fits +/- 10 AA batteries. Link to AAA version: https://www.thingiverse.com/thing:5437849 Category: Organization
AR15 magazine pouch attached to a belt. The pouches are connected from three elements with an elastic cord with a diameter of 3 mm. The belt holder is composed of two parts fastened with 4 M3 screws, 16 mm long. The chargers are equipped…
See attached PDF for instructions. Enjoy! Note: Not mentioned in instructions, but required a 3x2 magnet.
S.I.M.P. is a fully 3d printable Half Dart stringer pistol with an internal magazine that requires no extra hardware other than the elastic string. This Blasters fps will depend on the elastic put in it but it should have the fps as a…
(10/1/23) Overhauled the design to be a better fit with a wide range of magazine tolerances. Designed around genuine HK, MKE, Zenith/KCI stamped magazines. Untested with polymer magazines. A bit of grease in the cartridge channel can make…
It is a battery box like an ammunition magazine. Print Settings: Material: Spring parts must be printed with PETG. (PLA cannot withstand bending pressure it will break) Layer height: 0.2mm Supports: AAA_FloorPlate.stl Perimeters: 2…
Speedload your mags fast and easy: Pull the follower down a little bit so it's easier to get the little nose from the adapter to hook it. Pull the adapter over the mag with the nose facing the bottom of the mag I like to hold the adapter…
Speedloader for multiple types of magazines. Print one body then the Insert type/types you need and switch out just the insert. Easy Disassembly. Springloaded. Quick change insert/part replacement. 100% 3D Printed.…
Prop model of the famous 30 round AR15 magazine, this is a prop and it's in no way a functioning piece of firearm. The model is not scaled to size but the proportions are right, you just need to dial in the correct height in the slicer…
Recommendations It is recommended to print the models in PETG because the lid includes thin tabs which might break off if layer adhesion is bad. Print Settings Layer height: 0.25mm Perimeters: 2 Bottom layers: 3 Top layers: 4 Infill: 0%…
An extended magazine I created for the Glock Fidget Keychain – 3D-Printed Mini Slide-Action Toy by Rectangle. You can print standing on its bottom and no supports are necessary. I've created multiple other accessories for this model, you…
Supports are needed for the center section.
A handle for a Ruger 10/22 magazine, and magazine joiners. The 10-round magazines are fiddly things to manipulate, and recess into the rifle receiver. This handle gives you something to grab onto to extract stuck magazines, and to rapidly…
I was commissioned a Glock 17 magazine wall hanger so my customer could hang their magazines onto the wall instead of laying them flat on a shelf all the time. I made a 1 / 3 / 5 version so that people that have either more of less mags…
updated Version here : https://www.printables.com/model/1208363-akm-ak-47-1030-round-magazine-v2-ar-15-spring-comp This is a 3d printable Magazine for the AK 47 and AKM pattern rifles. Included are models for a 10 rnd version which has…
Edit 11/10/23: Add 9rd extension. Edit 11/9/23: Add v1.01 Vanguard variants to the files to accommodate Vanguard pushers. Also tweaked the follower for more spring clearance and lift. Edit 11/3/23: Add v1.01 files to introduce drum spring…
drapeau de mise en sécurité pour CZ455- 457 0.20 pla support seulement sur le plateau
AICS Long Action magazine for 30-06 based cartridges. This is long action and will not work with 308 AICS rifles. Nor will it work with long action 300 win mag. There's not enough room to make the feed lips strong enough for 300 win mag.…
This Magazine pull is ment to printed in TPU, an
This model is compatible with the lego system.
Note: Before printing, please measure the size of the magazine slot of the gun you want, and fine-tune the size through the slicing software to avoid the situation that the magazine cannot be loaded into the gun.
This is a magazine loader/thumb saver/speed loader for the Ruger Mark 1,2,3,&4 (I,II,III,IV).
A magazine I designed after my factory CZ one. Might require some hand fitting. The spring and follower are steel.
This is a 3d printable Magazines for the Tikka T3X Tac A1, CTR and Arctic rifles. Included are models for a 5 rnd and a 10 rnd version (with the 5 round variant being the more practical choice) which are a dircet replacement for…
I liked the original design by airbiscuity but the fitment was far too tight. I loosened the fit so the magazine will slide in and out easily but not fall during running. Secondly I changed the loops to be a belt clip that can be mounted…
These are Storz and Bickel Dosing Capsule Magazine funnels and stuffers. With this tool you can fill up to 9 capsules of the magazine at ones. Update (New and updated parts are added): -Version 2 of the multi funnels for 8 and 9 capsules…
Overview: A 3-piece bolt-together magazine sleeve designed to fit over the 10 round polymer magazines of the Derya TM-22 for an improved, P-Mag styled look. 2 versions available - one with a cutout to add spent brass, and one without. I…
Wanted to design a magazine rack to hold my kids activity and coloring books. You can use supports for this, however, it will significantly increase the amount of filament that you use and I advise against it. When printing, with my Prusa…
INTRODUCTION I couldn't find a nice curved (and free) MP5 magazine for my Mosquito so I created my own. Feel free to try it out and complain if you have issues. STEP files now available. The model is based on two existing models: - BB…
Here we have a spacer that will utilize one of the OEM base plates from a 12rd magazine, and fill in the gaps around the 15 rounder to make it comfier for your hand. I personally printed with fuzzy skin, but you do not need to. Nothing is…
I took the basic dimensions of a classic Nerf magazine, stared into the magwell of my Stryfe for good 20 minutes, and then sat at my laptop for 6 hours to produce this. Please keep in mind that I have no idea how to operate Fusion 360 and…
Working progress, will do some prints to bring it as low as possible. Remixed the Hochul Magazine Extensions File by @nnicclaascoupler to make the coupler, he did a great job, so the connection fits perfectly. Beware, if you connect two…
Custom magazine extension for magazine GL9 magpul Glock 17 + 2 extra ammo. The product is made in such a way that no screws need to be used.
Save your thumb! This is a simple speed loader for 380 Auto micro pistol single-stack magazines. It works well with the Taurus Spectrum, Bersa Thunder 380CC model, and probably other 6 - 10 round micro 380 pistols. You can use just about…
Speedplate for green gas powered glocks.
Edit 02/21/2023: Added ver.4 & STEP files. Added holes for set screw (M3). Lost original ver.2 so named the updated one ver.2.1. Edit 03/17/2020: Added image with ver.3 Base plate/grip extension for 10 round MecGar 1911 magazines. I…
A magazine Rack for the Honeycomb Storage Wall. Tested with Magpul PMAGs (5.56) (Holds up to 5) Settings: Infill: ~30% Supports: Yes
1/2/2025 user Jonathan Wolff reported box will also hold Anschutz 10 round magazines 8/21/2024 9/21/2024 Added two Savage labeled lids and one blank lid. 2/22/2024 User reddog kindly advised box will hold Savage MkII 10 round mags.…
Empty chamber / magazine flag for CZ 455, CZ 457 rifles in 22LR. LH versions including.
Model Quick and easy Magazine Extension for the great Disc Shooter from uhltimate . With the extension the Shooter could shot 12 rounds in a row. The magazine Extension is a snap-fit part. Simply slide over the original shooter, it holds…
Fits Glock Magazines (10). Should fit other similar mags, such as Sig9, Shadow, etc. Infill: 10-25% Support: Yes, Low Walls: 2-3 Tested in PLA and PLA+ @LiquidPizza
I was recently inspired by glgr with his curved magazine creation https://www.printables.com/model/938167-mp5-curved-airsoft-magazine-fits-mosquito) and saw there was not a 3D printed straight magazine for the Mosquito Open Beta 2, so in…
Speedload your mags fast and easy: Pull the follower down a little bit so it's easier to get the little nose from the adapter to hook it. Pull the adapter over the mag with the nose facing the bottom of the mag I like to hold the adapter…
This is a magazine for the easy rapid allignment of standart 125mm 8-hole oribital sanding discs on random orbit sanders. Works great for my Bosch GEX 18V-125. Take a look at the video below for a functional demo. Inspired by…
25rd AR22 STANAG Style Magazine Top is easily replaceable in case of damage. I included 2 styles of followers. The standard one which is the style my older Black Dog machine mags have. Bolt Hold Open is similar to the CMMG follower and…
MAGAZINE LOADER: https://www.printables.com/de/model/565260-hw-100-mag-loader-177-weihrauch (still work in progress [80% final]) ABS ! Layer 0.15mm ! without supports! PUT YOUR Z-SEAM here… There is a groove in the model to force the…
Simple holder for Glock an Beretta 92 style magazine. Fits 3 Glock magazines and 3 Beretta 92 style magazines.
Organizér na dokumenty či časopisy velikosi A4 i A5. Hexagon styl ušetří matreriál a ubere na váze. Organizer for documents or magazines size A4 and A5. Hexagon style saves material and loses weight. Print instructions I added a slit model
This is made for my Ruger 10/22. It goes into the magazine well and locks in like a standard magazine but it keeps the bolt locked open. It's a different style of chamber flag. I made changes to the flag for a much better fit in ver 2. In…
3/31/25 Version 2 is out! Realizing that you might not have the exact size screw you need, I made 2 versions using a M4x12 or M4x16 screw, depending on what you have in stock. Put the screw length above the screw hole. Added slots for…
Hello! :3 I found the lack of freely available magazine extensions for the HC Diana blaster quite shocking. There are some, but I could only find models that gave +1 or +2 darts, that kind of ball park. I know Nightingales work if you…
Do you like it? Please consider to buy me a cup cup of coffee . That would make my day! UPDATES 2023-05-05 Do you want to replace the cap with a shutter? Then have a look at Thomas1234 shutter:…
This is a custom base plate for an extended CZ Shadow 2 magazine. This baseplate can be used with picatinny rail attachments. My case was to attach Mantis, so it can be used together with a holster. Print it vertically with support (back…
Remington 597 magazine. Print Settings Printer Brand: FlashForge Printer: Dreamer Rafts: Doesn't Matter Supports: Yes Resolution: .100 Infill: Your choice, I used 45% honeycomb Filament: Proto Pasta HTPLA CF Black CF Category: Sport &…
*05.12.2024 I just noticed that on the rear part of the Long Levers, some dimensions are too tight/ not how i want them
This is a simple speed loader for the Smith & Wesson M&P Shield EZ pistol single-stack magazines in 380Auto and 9mm Luger chambering. It may also work with other magazines of a similar size, but is specifically crafted towards the M&P…
