1 / 6
Christmas Tree Phone Stand | No Supports, No Hardware — zdjęcie 1
1 / 6

Christmas Tree Phone Stand | No Supports, No Hardware

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The stand is a gift box with a gold ribbon belt and a bow on the lip, topped by a terraced 3D Christmas tree.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
15
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Turn your desk, nightstand or kitchen counter into something Christmassy without losing a single bit of function. The tree backrest leans your phone at a comfortable 70° viewing angle, a deep slot holds it (with a case!), and a cable notch in the front lip lets you charge while it stands. The star on top and the recessed ornaments on the back are made for painting or a multicolor print.

The stand is a gift box with a gold ribbon belt and a bow on the lip, topped by a terraced 3D Christmas tree. Turn it around and the back is fully decorated: layered boughs, a beaded garland and 10 ornament domes. A faceted 3D star crowns the top.

It is one solid piece, prints without supports and needs no extra hardware. Designed by ModuMaker.

Features

  • Fits big phones with thick cases: slot is 15.2 mm thick x 88 mm wide (tested on paper against iPhone 16 Pro Max and Galaxy S25 Ultra, 77.6 x 8.2 mm, plus a 5 mm case allowance)

  • Cable notch (16 mm) for charging while standing; works landscape-free, portrait use

  • Stable: phone's centre of mass sits ~37 mm inside the back edge of the base

  • Single piece, no supports, no glue, no screws

  • Fully sculpted back: 2 terraced relief layers, 18 garland beads, 10 raised ornament domes, faceted star

  • Gift-box base with raised gold ribbon belt and bow (every edge chamfered so it prints clean)

  • Raised details are separate colour zones: great for AMS/paint-on, still looks good in one colour

Print settings

Printer / nozzle

Bambu Lab, 0.4 mm

Material

PLA

Layer height

0.2 mm

Walls

3

Infill

10-15 % (gyroid or grid)

Supports

None

Orientation

As exported (base flat on the bed)

Overall size

101.8 x 91.8 x 140.2 mm (fits any 256 mm bed)

Volume

207 cm³ (model), less is printed with infill

Estimate (rough, not a slicer result)

~103 g and ~4.6 h at 10 % infill

Tip: no brim needed, the base has ~8600 mm² of bed contact. For the lightest print use 2 walls and 8-10 % infill; the stand stays sturdy because the tree is only 9 mm thick and the base is short and wide.

Colors (single color is fine)

  • Single color: print as is. Red, green or white all look good.

  • Paint-on: base red, ribbon + bow + star + garland beads gold, tree green, ornament domes red / gold / blue (as in the renders). The raised domes and beads give paint clean edges.

  • AMS multicolor: in Bambu Studio use the paint tool on: base (red), ribbon belt + bow (gold), tree (green), star + beads (gold), 10 ornament domes (red x4, gold x3, blue x3). A simpler 3-colour version: red base, green tree, gold for everything small.

Tagi