Liczymy pasujące modele…
I needed a 4in duct fitting after installing my AC Infinity AC unit as there were no more pre installed holes. This worked great. I used 5mm brass inserts in the plate. printed with the shorter length down with supports. The nut plate…
This is a two piece "clam shell" fitting that encloses the stock humidifier hose that comes with the AC Infinity humidifier. The fitting is then clamped around the hose and held in place a nut. Works great!. I've added two nuts, one with…
I made this , but saw another one here on Thingiverse. This one is more in line with the original design I think and I have it in my XJS (94). Printed wth 30% infill. Printed bottom down, not as depicted. *10-27-2025 I thickend up the…
Print the Roll scene "curvey" side down. I used a textured plate for this. The Briefcase squarish side down. Pawn shop can be done with either flat plate or textured. TPU of course. I used an piece of shrink tubing with s small piece of…
This is an enclosure for the Dialed In JJP pinball machine “Bob” signs as the originals were not backlit. You will need to make or purchase the .093 molex connector power connector kit from Mezel mods.…
I made this as I don't smoke, and would rather have a phone holder than two ashtrays...so here is what I came up with. Works good. You'll have to cut some of the excess carpet under it to get the clearance you'll need. It's stepped to…
I made this to use with my HRV (Heat Recovery Ventilator) as I could not find what I needed...I'm using this in a basement room where the wall is only on one side so I wanted an extra hole to pull from the room it is in... so two…
I made this to replace the original cigarette lighter base as the base kept popping out of the wood ski jump. Uses this led holder: https://www.amazon.com/your-orders/search/ref=ppx_yo2ov_dt_b_search?opt=ab&search=led+socket and these…
So this is for the Base (convertable in my case) rear speakers. The original mid range speakers were an odd specimen no longer availalbe. So what I did is I found a mid range speaker (Dayton Audio RS150-4), 6 inch and moved it forward…
I made this funnel to help fill the tube on the Super Shooter cookie press. It works great. I used PETG, but there are other food safe materials you can use. I printed with supports with the bottom of the funnel on the plate. Used ramdon…
I made this to replace the knee bolster clip on my XJS as my original was missing (well one of them) I also made a repair mount for this too if that is needed as well. Probably fits other models too. Category: Other
So this is a larger version of my T3 bulkhead, but basically assembles the same. You'll need two washers when you print it. I did it in PLA with supports, I think you only really need supports on the plate however. I did 25%infil on this.…
Made this to replace my moto massage on my Hot Springs hot tub. Printed with holes facing plate @ standard setting no supports. Category: Replacement Parts
I made this to move large snap in capacitors that need to be lifted off the board, specifically for the JJP power board. This is made for a 35mm diameter capacitor with 10mm leads spacing. Holes are larger than necessary to allow…
This bumper is used on my SJX 94, but probably fits many other models and years. Made from TPU, print hole up. I printed it at 30% infil. Interior molded for the head of the bolt it sits on. Category: Other
This is a flexible panel that sits at the bottom of the instrument cluster right above the steering wheel. My original one was deteriorating a bit and I reverse engineered it and came up with this. Some of the small holes may be off…
I made this to fit my XJS after replacing the factory antenna with the aftermarket one. The orginal mounting screws don't match up and I made this to make it more secure to the bottom. Uses M5 screws for the antenna. I used the original…
I made this to replace the handset holder on my VGO2007 model faucet. Its not symeterical so I put a dot on the bottom as its tapered. I suggest a test fit with the handset before installing it. I made this with ABS. Category: Hobby
I made this to replace the metal clips that were used on the original bolsters which apparently have become NLA. They seem to be working pretty good. I used 3mm nut and a 3x6mm machine screw pan head(try to find a thin one).I printed on…
I made to repair my knee bolster that had the one side ripped out. I used 5 min epoxy to mount this to the foam backing. Use a 5mm bolt (install before mounting the bracket) . It works good! The clip is listed in another listing.…
I made this for my PDU to hold the power supply and CD reader/CD's and board. This is what I used in this: Power supply Meanwell RD-50A (5VDC/12VDC)…
My original one deteriorated, so I came up with this one. Made of TPU. Category: Hobby
This sits behind the upper flipper and extends to the back of the target. Keeps the ball from getting stuck there as has happened to many owners. Printed bottom down at 30% infil I used ABS, with three perimeters. Category: Other
To wszystkie aktualnie dostępne wyniki.
