Liczymy pasujące modele…
Milwaukee M18 Battery Holder with Charged / Needs Charged Flags 4 Model files available, With and without the locking part for the battery clip as well as with and without the charged/ needs charged flag.
Small He is risen desk / table sign I have made. You would print it with the letters facing up from the bed (laying on it's “back”) I included the gcode file for print info generation on this site. I strongly recommend using the 3mf file…
This is a design I made to allow you to hold a tea carton (guers brand which is a local dairy near me) However it can also be used for milk, tea, other drinks that you may have in your area that are in a square pint sized containers. The…
Made a simple case nothing too fancy for my Irwin VISE-GRIP Convertible Snap Ring Pliers set. Separate slot for each of the different “heads”. If you would need to adjust the model due to printer tolerances for the lid fitting over the…
External Screen mount for the BTT TFT35 V3 which gives you access to the usb port and SD card on the screen. If this was mounted inside the control box where the original screen was. You would not have access to the usb port or sd card…
Fan guard for 6 Inch (150mm) Inline Fan duct fans was built for the “fan guard for TerraBloom 6 Inch (150mm) Inline Fan” sold on amazon but would probably work for others. This would be useful if you aren't using the duct connection on…
This is a vent duct adapter for a Honeywell AC so you can add a 6" flexible duct to the intake side, this should also work on the discharge side as well. You would attach the flexible vent duct to this piece and tighten it using a hose…
This is a large 2 door igloo for Guineapigs and other small animals. Note you will need a printing area of 320mm x 320mm x 160 or larger to print this. Print Settings Printer Brand: Creality Printer: Ender 5 Plus Rafts: No Supports: No…
Made an 8 slot pressure washer nozzle case with drain holes. This will provide enough space for the standard 5 nozzles (e.g., 0º, 15º, 25º, 40º, 65º(aka soap nozzle) ) As well 3 spaces for 2nd story nozzles or any other specialty nozzles.…
Ford and it's infinite insanity designed the headlight on the 2016 Fusion as well as other year models where you have to drop the bumper to change out the low beam bulb. However, there is a few videos on youtube where people have removed…
Print it with the flat side towards the bed, I was able to print it without supports. I recommend using the 3MF file I attached and not the gcode. Remix of the Ender 5 Micro Swiss Direct Drive Cable Drag Chain Stepper Motor Mount (Linear…
Box to store Irwin Speedbor bits (IRWIN SPEEDBOR Drill Bit Set for Wood, 4-Inch, 6-Piece (1877239))
Hook tool for use on painters' poles, one use would be for hanging Christmas lights up in trees etc… Prints without supports, works on standard painters pole threading. I did include the gcode file for reference only, use the 3mf file to…
New microwave had a straight plug as opposed to a right angle plug. Which makes it stick out. Over time of opening and closing the microwave it will shift back against the plug. Overtime this could cause damage. This solution will simple…
Note this is a work in progress. While it does work, it does have room for improvement. This will allow you to mount a Revo Hemera XS Extruder onto a Ender 5 Plus that has the Zero G mercury upgrade. I printed my parts using ASA as I did…
Co-Print Chroma Print head mount for a Ender 5 Plus that had the mercury one upgrade The front plate takes 5 - 3mm x 5 threaded inserts. 3 for the Chroma Head and two for the belt clamps. Included a back view diagram where to add the…
UPDATE: Added a newer clip design to allow you to attach it to a printer with belts that sit in front of the X-axis rail (e.g., in a Mercury One setup). This is a separate file. Also adjusted the height of the original bracket to help it…
If you feed your guineapig vitakraft crunch stick treats, you would know that the “mount” that comes with them make them hang vertically in their cage. I'm sure you would also know that due to the configuration of the head of Guineapigs…
Mount for CoPrint Chroma Pad. It has multiple 4 mm holes for mounting it from it's center or close to it's edges. The screen cover gets mounted with 4mm screws using 4mm Heat Inserted Threaded inserts into the mount. As always use at your…
This is a holder for Magic Bullet blender blades. It can hold 5 allowing you to stack them up without them falling over. Prints without supports. Use the 3mf file to slice it yourself for your printers specs, I don't recommend using the…
I have a couple of these plastic shelves from Amazon (see picture of shelf and link below to amazon posting). The shelves are held together with plastic pipes. On the top shelf, they have this nice opening where things can fall into it…
The manual shows how to tie the guide wires directly to the antenna, but I made this to give you something to tie to. I attached mine to the 6 point spider just above the 20 M trap. (I'm using the 5BTV however this should work on the 4btv…
Cover for the DXE-VMN-1 Vertical Antenna Matching Network from DX Engineering for the Hustler 4btv 5btv 6btv I Printed it with ASA to protect it from the elements. It is in two parts so when your slicing software ask you about combining…
This one was designed for the Streamdeck .mk2 not sure if it works on the older version. The mount was designed to hold a Streamdeck .mk2 and space behind it to hold a raspbery pi zero in the back. There is two zip tie slots inside in the…
Toolbox tray organizer for Westward Precision Tip Screwdrivers. These connect together, there is 5 different modules. Middle Module holds 1 driver plus a half on each side, End left or right 05 closes off the tray and only holds half a…
Made a cover for my space mouse to protect it from being bumped by stuff around the desk when it's not in use. Prints in two seperate parts, base and top cover. As always use at your own risk.
To wszystkie aktualnie dostępne wyniki.
