P
PrintablesDan_Mc
Magazine Loader - Sig P322
This printed in PETG with 5 walls, 0.4mm nozzle, "IS Speed profile on a Prusa MK4, in about 90n minutes.
- Pobrania
- 187
- Polubienia
- 16
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesDan_Mc
Microjig replacement gravity heel
I made this to replace the consumable gravity heel on my Microjig Grr-ripper push blocks. This printed in about an hour on the MK4 with a .2mm layer height with PETG.
- Pobrania
- 164
- Polubienia
- 33
- Ocena
- 5
P
PrintablesDan_Mc
Blum Movento 629 Lock Drill Guide
I couldn't find the Blum drill guide I bought to use with the locking mechanisms of the Blum undermount drawer glides I was installing. After checking Printables and not finding what I needed, I modeled this and printed it in a whole lot…
- Pobrania
- 154
- Polubienia
- 29
- Ocena
- 0
P
PrintablesDan_Mc
GM Diesel capless filler plug
Went to fill my DEF tank the other day and stuck the DEF nozzle right in the cap-less filler for diesel fuel. Fortunately, I caught myself before I was forced to learn an expensive lesson. I thought a plug to go in the capless filler hole…
- Pobrania
- 147
- Polubienia
- 16
- Ocena
- 0
P
PrintablesDan_Mc
Jeep JL Floor Mat Plug
My Jeep cam with rubber floor mats but no plug for the oval drain hole, leaving a clear path to the carpet. Fusion 360 and my Prusa MK4 to the rescue. Printed in PETG, as oriented, flat down.
- Pobrania
- 108
- Polubienia
- 26
- Ocena
- 5
P
PrintablesDan_Mc
Ruger MK Recoil Spring Guide Rod Cleaning Aid
As always, wear eye protection when messing around with springs, or don't do it if you do not feel comfortable working with something. It is tough to clean the gunk off of the Ruger MK series guide rod, because the spring gets in the way.…
- Pobrania
- 77
- Polubienia
- 8
- Ocena
- 0
P
PrintablesDan_Mc
4" Bolt on Flange and Drill Guide (Rockler Dust Right Handle Compatible)
This works with the 4" Rockler Dust Right system. There are 12 holes to attach it to your equipment - I used #10 sheet metal screws and washers. The flange part printed in less than five hours on my Prusa MK4 with a .4mm nozzle and .3mm…
- Pobrania
- 59
- Polubienia
- 12
- Ocena
- 0
P
PrintablesDan_Mc
Omniwall Drill Bit / Driver Holder
For easy access to the most often used ¼" driver bits and ¼" quickchange drill bits. This holder hooks on the steel frame of the drill/driver holder, then slides forward to lock in place. Mirror in the slicer to mount on each side.…
- Pobrania
- 55
- Polubienia
- 6
- Ocena
- 3
P
PrintablesDan_Mc
Rugged Radio Holder With Ball Mount
Works with the Bulletpoint knockoff Jeep JL ball mount system sold on Amazon and the Rugged Radio handheld with microphone. I used Organic Supports and oriented the ball mount with the ball side down. Ball side down seems to give a nicer…
- Pobrania
- 51
- Polubienia
- 15
- Ocena
- 0
P
PrintablesDan_Mc
2 1/2" Dust Buddy Hose Adapter and Accessories
I like the Rockler Dust Right 4" quick connect dust collection adapters, but they do not make one for 2 ½" hose. This collection provides quick connect/disconnect for 2 ½" flexible dust collection hose (approximately 63.4mm I.D.) to 2 ½"…
- Pobrania
- 46
- Polubienia
- 6
- Ocena
- 0
P
PrintablesDan_Mc
American Plumber WC34 Whole House Filter Wrench
Plumber didn't leave a wrench after installing an American Plumber WC34-PR whole house water filter. Needed one and couldn't find a model of exactly what I needed on Printables, so I modeled and printed this one. I used eight perimeters…
- Pobrania
- 45
- Polubienia
- 7
- Ocena
- 0
P
PrintablesDan_Mc
Mag Bumpers and Jigs for Wilson 9mm 1911 Magazines
I wanted to add some TPU magazine bumpers to my Wilson 10 round 9mm 1911 magazines. The base plate did not have any screw holes, so I also made a jig to mark and drill them. The marking jig uses a 6mm transfer punch to mark the hole…
- Pobrania
- 45
- Polubienia
- 6
- Ocena
- 0
P
PrintablesDan_Mc
Sunpak Tripod Replacement Quickrelease
We got a tripod for the thrift store and it was missing the quick release camera mount. I made this to use with a ½" long ¼-20 bolt to attach a Ram Mount ball. It works perfectly. Printed with PETG and no supports.
- Pobrania
- 42
- Polubienia
- 2
- Ocena
- 0
P
PrintablesDan_Mc
Magnetic Apron Clasp and Tie Retainer
I bought a cheap apron of Amazon to protect my clothes during glue ups. After having trouble making knot behind my back, I decided a couple 12mmx6mm magnets and my printer could help out. The parts are printed from PETG, and th magnets…
- Pobrania
- 24
- Polubienia
- 6
- Ocena
- 0
P
PrintablesDan_Mc
Toto Bidet Controller Holder For Command Strips
I wanted a way to mount the Toto S7A remote to the wall without using the commercial mount that requires screws to mount to the wall. This mount has a 2.5mm recess in the back so it sits closely to the wall with hook and loop Command…
- Pobrania
- 23
- Polubienia
- 1
- Ocena
- 0
P
PrintablesDan_Mc
Corner Routing Template: Small Radius
I like to route the corners of slab drawer fronts first, so I end up with nicely blended corners. Trying to route the short edge of the panel is awkward and inconsistent. The 3mm guide closely approximates the radius required for an 1/8"…
- Pobrania
- 20
- Polubienia
- 2
- Ocena
- 0
P
PrintablesDan_Mc
Table Saw Blade Cleaning Fixture
I wanted a way to presoak the carbide teeth of my saw blade and also wanted to have the blade held in a position that made cleaning all faces of carbide easier. Since I started using this fixture, I have been more likely to clean my…
- Pobrania
- 19
- Polubienia
- 3
- Ocena
- 0
P
PrintablesDan_Mc
Pact III Shot Timer Legs
Leave your Pact III timer on the bench with these legs. Print in the orientation as modeled for best strength. Using Organic supports and IS_2.0Structural, it printed in less than an hour with PETG settings on my MK4. I used a small nail…
- Pobrania
- 18
- Polubienia
- 1
- Ocena
- 5
P
PrintablesDan_Mc
Low profile 3/4" PVC vacuum nozzle for pizza oven
I couldn't effectively vacuum the back of my pizza oven to remove burnt whatnot and crumbs after scrubbing with a wire brush. Prusa, Fusion 360, and a short piece of 3/4" PVC to the rescue! I printed this out of PETG, oriented with the…
- Pobrania
- 17
- Polubienia
- 3
- Ocena
- 0
P
PrintablesDan_Mc
Whirlpool Dryer Hinge Cover WP33001764
When reassembling my Whirlpool Atlantis dryer, I discovered that the hinge covers were cracked. I looked at buying new ones, but apparently Whirlpool is very proud of these things, and I didn't want to spend that kind of money or wait.…
- Pobrania
- 17
- Polubienia
- 3
- Ocena
- 5
P
PrintablesDan_Mc
Command Strip Mantle Hook
We wanted a removable way to decorate our fireplace mantle for Christmas. This hook prints fast and has worked great for securing garland, lights, stockings, and decorations. Flat brown filament made them disappear in the garland.
- Pobrania
- 15
- Polubienia
- 1
- Ocena
- 0
P
PrintablesDan_Mc
.2mm to 3.8mm Shims
When installing a new toilet it rocked due to the flooring being uneven around the closet ring. I don't like commercial shimming wedges because they take too much work to trim. These are stepped in .2mm increments from .2mm to 3.8mm. Just…
- Pobrania
- 12
- Polubienia
- 0
- Ocena
- 0
P
PrintablesDan_Mc
Battery Door For Laguna Dust Collector Remote
The sliding door for my older Laguna dust collector went missing. I checked with Laguna and a replacement is not available. Out came the calipers and Fusion360. Printed in PETG If you find this useful, I hope that you post a picture of…
- Pobrania
- 12
- Polubienia
- 1
- Ocena
- 0
P
PrintablesDan_Mc
Scroll Saw Blade Holder
This is used to store several tubes of scroll saw blades. There are three parts in the version that works for the scroll saw blade tubes I use: a magnetic base, a holder that drops in the base, and sleeves that reduce the diameter of the…
- Pobrania
- 8
- Polubienia
- 1
- Ocena
- 0
P
PrintablesDan_Mc
Blum MZK100 Geartrain Gasket
I bought a Blum line drill with the MZK1000 seven spindle boring head. The bearings needed to be replaced, and the original gasket was damaged beyond repair when I disassembled the unit. I modeled this one and printed it from TPU in the…
- Pobrania
- 4
- Polubienia
- 2
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.