Liczymy pasujące modele…
This wrench allows you to remove and install the antenna on a Jeep Wrangler JK (and perhaps others models). I keep this in my center console so I can easily remove the antenna before I go through a car wash. You might need to use an…
This grommet protects your shore power cable and fresh water hose as they exit the power and water bays of Tiffin Class A RVs. Tiffin installs a grommet formed from a length of rubber gasket material. With use, this gasket can become…
I use this scribe to mark waterlines on the hull of a model ship or boat. Clearly, it can be used for other purposes where an adjustable-height scribe is needed. The arm has a hole/slot for a 5/64 (2mm) lead or blade; I found these among…
These parts can be used to repair a 6-port hummingbird feeder. The opening for the feeder's glass tube is ~3.1 in (79 mm) diameter; the nectar tray upon which the top sits is ~5 ¾ in (147 mm) diameter. The original plastic parts weaken…
The William Bounds, Ltd. HM 8in Professional Pepper Mill is a wonderful device. However, after a number of years of excellent service, the plastic core within the stainless steel cap fractured, rendering the mill difficult to use. The…
Caps to prevent foreign object ingress in ¼ inch female quick disconnect fittings. Two sizes are provided. The 7/8 inch cap is shown on an air hose. The 15/16 inch cap is shown on my RV (for the toad's brake controller). I printed these…
These dividers keep tall items upright in the narrow sliding pantry found in some Tiffin RVs. The dividers, which are 4 in. wide and 6 in. tall, prevent items from falling over or hitting one another while driving. A 1/2 in. x 1/8 in.…
This part replaces the metal top and perch of a 4-port hummingbird feeder. The threaded bottom of this feeder's colorful glass bulb is ~1.7 in (~44 mm) diameter; the nectar tray upon which the top sits is ~4.7 in (120mm) diameter.…
This adapter mounts a laptop optical disc drive in a tower PC's 5.25 in drive bay. My dear wife's 5.25 inch internal BluRay writer drive suffered a catastrophic connector failure. When I tried to replace it, I found out those devices are…
This replaces the check valves of a Flo-Master HD-1, Lawn & Garden Sprayer. The OEM part identifies itself as Mono Valve 151-400; it has a 23mm disc diameter. Two valves are used, one at the bottom of the pump tube and the other at the…
This mount attaches an ASIAIR Plus controller on a William Optics Ultra-Cat 108 telescope. The mount uses two M4-0.7x8mm screws for the ASIAIR Plus case bottom and two M6-1.0x10mm screws for the Ultra-Cat 108 tube mounts. The scope's tube…
This mount attaches an ASIAIR Plus controller on a William Optics Ultra-Cat 108 telescope. The controller is mounted horizontal relative to the telescope. The mount uses two M4-0.7x8mm screws for the ASIAIR Plus case bottom and four…
This is a plug for the tab mounting holes on a Blue Ox baseplate. It prevents debris from collecting in the hole when the tab is not in place, e.g., when your toad is not being towed. Two are needed, but you knew that ;p I printed these…
This mount attaches an ASIAIR Plus controller to a William Optics MiniCat 51 WIFD telescope. While the scope's tube clamp provides a location to mount the controller, this mount repositions the controller so USB cables attached to the…
This fixture will keep the gas burner controls of an Atwood CV-35BP RV cooktop in the off position. The fixture is easy to push on. It is readily removed by pressing the top of the knob as you pull the fixture off. The burner knobs are…
The Maytag MTB2656AEW top-mount refrigerator freezer shelf brackets allow the wire shelf to rotate open. These brackets replace the existing brackets when they have failed. The OEM parts are removed by using a flat-blade screwdriver in a…
The perfect coaster when you watch a true classic, The Big Lebowski. This was printed in PLA at 0.1mm FAST DETAIL and default slicer settings.
This arbor allows the 3 jaw chuck to be mounted on a common 28BYJ-48 servo. The arbor replaces the backing plate that secures the face housing to the scroll and mounts to the servo's 5mm Double D shaft. The part was printed in PLA at…
These parts can be used to repair a 4-port hummingbird feeder. This opening for the feeder's glass tube is ~3 in (76 mm) diameter; ; the nectar tray upon which the top sits is ~5.6 in (142 mm) diameter. The original plastic parts weaken…
This shelf divider fits on the wider door shelf of a Sub-Zero refrigerator. This was printed in PETG at 0.2mm STRUCTURAL and default slicer settings. No supports are needed when the part is oriented with the top on the print plate.
To wszystkie aktualnie dostępne wyniki.
