Liczymy pasujące modele…
Note that this model has been superseded by this new test square. I find it easier, as well as being faster, covering a wider range of nozzle offsets, and having a finer resolution. This is a test print to help fine tune a printer…
Wydruk około 0,09 €–0,12 € nettoWstępna wycena jednego wariantu
Note that this model has been superseded by this new test square. I find it easier, as well as being faster, covering a wider range of nozzle offsets, and having a finer resolution. This is a test print to help fine tune a printer…
Wydruk około 0,09 €–0,12 € nettoWstępna wycena jednego wariantu
This model is of the steel ball weapon from the anime Jojo's Bizarre Adventure. A step version is included to facilitate modification. I had luck printing the halved version (print two copies as the halves are identical) at 0.1 mm layer…
Note that there is now a test model that also searches for the correct Z offset for each mesh point . I feel this is more useful than this model. Designed this print to help me dial in each location in a 25 point manual mesh bed leveling…
This is a tilting style mousetrap with an adjustable magnetic release for a snap action. The counterbalance weight is also adjustable. I designed it to work with pennies, but the two threaded plugs can sandwich any type of mass and allow…
Note that you may want to check out the newer, fully customizable version instead. Wall plate to guide low voltage cabling. Requires no supports when printing. I used some #6 wood screws to attach it to the wall bracket (also 3D printed:…
This gcode will help find the correct z offset for a 3D printer's nozzle. It is a back and forth square (hence “oxplow”) that begins at -0.1 mm below the current nozzle offset and raises it each row until it ends at +0.1 mm above the…
This Fusion 360 file will parametrically create gears that can work with threaded rods or bolts either as a worm gear or as a pinion (using the threaded rod as a rack). The thread is defined by its dimensions as parameters and a diagram…
This is a bottom cover for the 2018 Mac Mini. Replacements are oddly expensive online and I was making another project that attached using the cover's system and since that's the hard part to model I figured I might as well make this…
Designed this print to help me dial in each location in a 25 point manual mesh bed leveling grid (individual offsets can be edited). It is an improvement on my previous test pattern as it now searches for the correct Z height when…
This gcode will help find the correct z offset for a 3D printer's nozzle. It is a back and forth square (hence “oxplow”) that begins at -0.1 mm below the current nozzle offset and raises it each row until it ends at +0.1 mm above the…
Update: Changed the tip to more closely resemble actual pictures, rather than the dimensional drawing's more rounded nose. Model of 5.56 NATO and 0.223 Remington ammunition (while very different in performance, they are dimensionally…
This is a trigger guard for the Ryobi P737D 18V inflator. Found it'd get triggered sometimes when I'd toss it in my trunk when going biking. Printed in two pieces to increase the strength of the parts. Can attach with a single screw, but…
This is a counterweight to balance the front-heavy Valve Index VR headset, using pennies. It is compatible with the Index's "Headset Cradle Adapter" (the foam pad meant for smaller heads). Included is also a version that redirects the…
I created a more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). This model is a nozzle that's equivalent to the inflator…
This design is the two and three button versions of the Amiga "pregnant" mouse. I didn't model the cord, but did do the plug. I made it only from pictures I found online, which required a lot of guesswork, so I'd be most grateful if…
This design is for a 3M compatible respirator filter cartridge that can accept a variety of filter media. Since FDM prints are porous and must be filled and painted to be properly sealed, this design is based around a PVC clean-out plug…
This design is for improved grips for XT60 connectors to make disconnecting them easier. It also will strain relief wires. Split in half to allow assembly onto existing connections, but that means they do require gluing. Additionally, the…
Full height PCI expansion slot covers for a computer case that can be used as filtered air intakes. Widths one through seven are provided, though the smaller sizes are arguably kind of silly. It is designed to accept filter foam that is…
This adapter allows easy attachment to the Valve Index's controller (Knuckles). It is intended to be a base for other designs, rather than being useful itself. I used a 0.2 mm clearance which works well on my printer but might not be give…
This model allows a dial indicator to be attached using the stock SV06's fan mounting bracket screw holes, presuming the fan has been upgraded and relocated. A rear-mounted holder would be stiffer, but if you've already taken that space…
There is now another version of this trap , that requires no gluing, end cap drilling, or a length of CPVC pipe. It does require more printing and a 12" long ¼"(or 6mm) metal rod, however, so decide for yourself which you prefer. This…
These are models of an Amiga 3000 faceplate, power button, and drive cover. Note that they are meant as a starting point for Amiga 3000 themed cases and the like, not as actual direct replacements for the original parts. As such, STEP…
This design is for a more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). The adapter doesn't permanently modify the…
This is a variation on my earlier design that now requires no gluing, drilling of the end caps, or a length of CPVC pipe. Older one is faster to print and doesn't require a metal rod so may still be a better choice for some people. This…
This hook is tailored to the geometry of this particular set of headphones, matching the cushion curve and width. Models should be printed in their current, sideways, orientation for strength. Two versions are included to allow the hook…
This design adds locking tabs to prevent a rubber Curt 1.25" trailer hitch tube cover from working its way out over time. I'd suggest PETG rather than PLA for its higher temperature resistance, and printing with 100% infill makes drilling…
This adapter is intended as a basis for other designs. It affixes to the 40V Ryboi leaf blower model RY40402VNM. Original idea for a duster nozzle required too sharp a taper to work properly, but figured the adapter part might be useful…
This design is a custom holder for this Medical Kind brand walking cane , though a step version is included to facilitate potential adaptation to other models. I tested it with a different cane and other than it being snug because of its…
This mount allows a Dremel 395 to be mounted onto an arbor press to act like a miniature drill press. It has been remixed from the source design to work with 8-32 nuts and screws and optionally a 1/4-20 bolt can serve as a depth stop. I…
This design is a variation on my more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). It adds storage for a spare nozzle…
This is a spacer for a Petsafe microchip cat door (model PPA19-16145) to allow a more polished looking installation in materials that are thinner than a standard door. Not very much structure is required, but a full width version is also…
This design is a button guard for the Litter-Robot 3. It is very easy to accidentally press the "empty all litter" button rather than manually cycling the machine so this covers it, making it impossible to press with a finger. Instead,…
This is a flat back cover for the cheap Harbor Freight Cen-Tech dial indicator. The stock one has a large mounting loop that can get in the way. Uses the same screws the original came with. In case they've changed the model since I bought…
This design is for a metal dish holder for the Petlibro PLAF004 automatic pet feeder. It came with a plastic bowl which apparently can, over time, lead to "chin acne" (their newer models now have a metal insert). The bowl it's designed to…
This is a model of an Art Deco rising sun radio speaker grille. STEP version is included to facilitate reuse. Print Settings Rafts: No Supports: No Category: Art
This design adds larger buttons to Anker Q30 headphones (transferring presses to the Q30's buttons beneath). The standard ones can be hard to find quickly, especially if wearing gloves. The new buttons can be pressed either axially or…
Some SV06 printers have frames that are sufficiently out of square that the built in "Auto Z-Align" function cannot work well enough for the ABL system to perform properly. These models add frame mounted adjustable positive stops to…
This adapter allows a tube to be run through the wall (or cap) of a container. This second version of my tubing bulkhead / panel fitting requires no additional hardware, though is less compact. The body and caps are printed in different…
This model demonstrates compliant mechanisms (modeled from a diagram I saw online). Allows motion in X and Y while resisting rotation. Has a handle to make trying it out easier. Attach it with sixteen screws to a flat backing. Probably a…
Note that it is rare that someone would need to change their X or Y steps. That said, this is a simple one-nozzle-width, one-layer-high square test model to check their accuracy. Measure the distance between the line centers, keeping as…
This design allows an ordinary male XT60 connector to be mounted behind a panel. Uses through-bolts for mounting to mitigate layer-adhesion strength concerns. The body can be scaled in Z in a slicer to account for differing panel…
This design is for remote PC power and reset buttons. The buttons connect via a USB 2 cable to a PCI slot mounted port that can optionally also have power and reset buttons. Note that the remote switch is deliberately kept small so…
This is a four degree of freedom mount originally designed for a small LED projector. Wanted something easier to adjust finely than a ball mount and I needed the extra DOF for my particular situation. Designed around an "L" made of 1/2"…
Some SV06 printers have frames that are sufficiently out of square that the built in "Auto Z-Align" function cannot work well enough for the ABL system to perform properly. These models add frame mounted adjustable positive stops to…
Note that there is now a second version of this design. That one requires no hardware, but is a little more bulky and probably a little less robust than this one. Wanted to make a brake bleed container for my car and realized I could just…
Replacement backplate for an inexpensive LED dimmer control (see link) that allows it to be easily mounted to the bottom of a desk. Great for use with a LED strip for a keyboard shelf light. Simply unscrew the back and replace with this…
Easier to grip knob for the C200 Cat Mate automatic feeder that won't block the opening mechanism. Pry out the old indicator arrow with a small screwdriver and install in its slot. Mine fits tightly enough to stay without glue, but some…
Gluing some sheet metal to this extremely simple model will allow an inductive bed leveling sensor to be spoofed, making the printer think it is lower than it actually is. This is useful to more easily allow a height sensing tool such as…
This design will allow this ¼" thumbwheel ratchet (and perhaps others) to be housed in a plastic socket set case, presuming there's room for it someplace. It has retaining tabs to keep it from falling out and a slot to get a finger in…
These trays allow ice cubes to be used for cooling the food in a Cat Mate C500 automatic pet feeder. Be sure to use cubes that aren't too tall (22mm or so). In my testing there was no leaking, but depending on your printer and settings…
To wszystkie aktualnie dostępne wyniki.
