Liczymy pasujące modele…
The Sovol Zero toolhead's umbilical cable doesn't hold its shape terribly well, and can sag or get pushed into things around the chamber (and cause a pretty bad day in some cases). This is a simple connector clip to attach the PTFE tube…
Models of the OEM spool holder and chassis mount for the QIDI Plus4. These are modified versions of the models from QIDI, but slightly more appropriate for 3D printing (vs. injection molding). I haven't printed these yet, and they have a…
The electronics bay on the Sovol Zero is separated from the chamber, but not terribly well. There's a bunch of places where air can slip past, which means if you're heating your chamber for ABS/ASA or other warp-prone materials, you're…
I didn't like the stock Sovol Zero spool holder; the little PTFE hack they used to reduce friction helps, but not nearly enough compared to something with proper bearings. Thankfully I'm feeding out of a drybox most of the time, but…
I relocated the power supply underneath the bed on my Anycubic Mega SE, and removed the cheesy plastic endcap they used that also held the power plug, fuse, and switch mount. This is a simple box to hold the IEC320 C14 fused power socket…
This is just a simple clip that snaps in flat against the 1515 extrusion channels inside the Sovol Zero, and leaves room for light-gauge wiring behind it (LED wiring, etc). These are 15mm x 15mm, and sit very low against the extrusion,…
I liked Segan's matchstick LED mounts, but I had a pair of the RGB LED strips instead, which have a different mounting hole pattern. I also use Michael Sheldon's PTFE connector mount , which required opening up and moving the PTFE hole in…
It's a simple LED holder for the North (non-XL) PC case by Fractal Design. It's meant to fit between the lower platform (that houses the power supply and any drives) and the outer panel of the case, covering the original Fractal logo (so…
Expands the openings in the 2.4 350mm panels, originally meant for passing the Z belts through, to make room for the Z tensioners mounted to the lower frame rail.
A simple two-screw wall mount for a Nortek HUSBZB-1 ZigBee/Z-Wave USB controller, to lift it up and away from my Home Assistant Yellow and improve the range.
Some important notes if you're reading this: The deep version of this is a MOSTLY UNTESTED model. I've printed it once, determined it's dimensionally correct, and then got stuck working on something else. I haven't even tested if the back…
I'll be using a Mean Well LRS-50-5 power supply in my printer, and since there wasn't an existing FT EMS mount for it, I made a quick model for it. I tried to retain the house style, so it shouldn't look out of place next to other mounts…
The stock power supply in the Sovol Zero is only 150W, which doesn't really give any headroom for upgrades. This is a mount I quickly modeled up for attaching a Meanwell UHP-350 series power supply (or a compatible knockoff) at the front…
This is a chonky little housing for an F695 (flanged) bearing which mounts directly (or through a mounting plate) to a NEMA 17 stepper motor, to provide additional shaft support when running higher belt tensions. The bearing fitment is…
The power supply that came with my Anycubic Mega SE is one of several variations of the Chengliang P400W24V, a 400W 24V power supply. Because I switched to dual-Z, I wanted to relocate it from it's stock location behind the gantry…
I loved @shoeys_for_newey 's riser feet , since they gave me room under the Sovol Zero chassis for cables and other random things, but when I added a larger PSU , those feet didn't work anymore (the PSU was in the way, and even if it…
I own a Qi car charger with a little button on the back surface that, when pressed (when you press a phone's back against it), causes arms on each side to release and clamp down on the phone. This worked great until I bought a Peak Design…
It's a cylinder with a hole in the middle. WITH CHAMFERING, that's how you know it's high-quality. Did you do something silly like toss a large power supply under your Sovol Zero, and now you wish you had just a little more room under…
The mount for the BTT Manta M5P in the mounts repository is an early design style, and I wanted something that looked more like the newer mounts (and some of the other EMS mounts I've published), so I made this one from scratch using the…
I'm running the XY motors on my Annex Engineering K3 at 48V, and I'm using BTT's external TMC 5160s (TMC5160T Plus) as the stepper drivers. I needed to mount them, and specifically, I needed enough room for an Octopus Pro (mounted…
I picked up some fancy new Dewalt 20V 10A batteries, and suddenly realized the ancient charger that came with my first battery-powered drill was no longer going to be up to the task. So I also grabbed a Dewalt DC1112 charger, which was…
I added a 100W chamber heater to my Sovol Zero, which ended up becoming a little bit of a project. I needed to be able to control the 12V fans and heater element, and didn't have enough spare ports on the mainboard , so I used a Fly…
This is a replacement cover plate for a standard US 1-gang wall toggle switch (using the device mount holes, not the gang mount) that accepts the decorative mounting plate from a Philips Hue Dimmer Switch v2 (mine identifies itself as a…
To wszystkie aktualnie dostępne wyniki.
