Liczymy pasujące modele…
V2 version adds possibility to mount two additional PowerCon outputs instead of third SchuKo-socket with adapter plate. *********************************************************************************************** Was in need of a…
Wydruk około 13,60 €–16,62 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Rotated the outlet about 15° to clear the sixth mounting position for putting in screw from top. Also embedded M3 nuts into the lower (no support needed). Mounting with M3x12mm or longer. I uploaded a print file for Mk4S with three…
Wydruk około 6,76 €–8,27 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I designed my own snap smd storage boxes. The boxes come in multiple packs (cheaper to print and more easy and sturdy to connect) and sizes. The lids were connected with a piece of filament (1.75mm). The boxes can also be connected via…
Sick of these lids flying around inside the drawer I created these stack cages. The height fit inside the drawers for IKEA IVAR.
Version 2 with interlocking hooks for no gap movement at all, prints without support. Available in two lengths (68 mm and 80 mm). =============================================================== I designed a printed variant of neutrik na…
I designed two holders for my IKEA HEAT mats. One can be mounted on a shelf board holding 5 mats.
Mount for TP-Link TL-SG105 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.
Mount for TP-Link TL-SG108 with cut outs for air vents. Under the mount are two channels for the dc supply cable. Mounting is done with 4mm sink head screws. Print with front facing down.
Side rail for IKEA IVAR shelve (30cm)
I created these modular drawers for organizing electronic components into my IKEA Kallax that was sitting next to my desk. Inside one of the squares will fit 4x4 base grids. I designed the frames to be one grid high and two grids wide.…
I remixed the tool holder from SixtyFourWarrior to fit my needs. This version is a little bit less wide and in addition I added space for my tweezers and a side cutter. The X-Tool can be hung next to the scraper as well. To be able to…
This is a licence plate holder for S51. The shape of the rear fender is adapted, the distance between the mounting holes is smaller then from the technical drawing (german licence plate) due to outward moving of the screws. I'd appreciate…
This is a licence plate holder for KR51. The shape of the hull is adapted, the distance between the mounting holes is smaller then from the technical drawing (german licence plate) due to outward moving of the screws. I'd appreciate some…
Small stop block for the IKEA Trofast shelf. Just mount it in the rail with an screx 4x16 flat to the rear. The boxes will stand out a little to the front.
I created a cymbal nut with printed threading for backup needs.
I creaded this 3d printable model of the molle lid grid for my Peli 1560 to be printed on my Anycubic Kobra 2 Max. The parts are connected with 1,75x16 mm metal rods (filament should work as well) and are mounted together with the spacers…
For labeling Neutrik XLR (XX-series) with text I use the clear code rings sold by Neutrik but they are quite loose so I created a balancing piece. I also created my own version of the color coding rings. There are lots of other models…
I created this beater holder for my Kenwood CookingChef attachments for mouting everything on my shelves. Mouting is done with two 4x20 mm screws.
Here I share my version of the so called Riggers Multi Tool. None of the ones to buy suited my needed so I created a new one for 3D printing. The multi tool contains the following fittings: M10 butterfly nut M6 butterfly nut 22 mm nut…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box containst Wago connectors (221-415 and 221-613). The connectors will clip in place, for convenient extraction are some slits in…
I did not want to decide wich of these two designs I preferred so I remodeled the lid of the Prusa Core One Side Storage by @Prusaguy to match the skadis pattern from the Prusa CORE One SKADIS mod by @ScottWolfs including the dividing…
I created a modular inlay for my Pelican 1560 Toolcase - Printable on i3 style printers. ==== This is currently still a WIP ==== I am working on and using this inlay system since more than two years now so I decided that it is time to…
Due to the handlebar on the Simson Schwalbe beeing covered by a shield plate, I designed a smart phone holder adapter to fit the plate above the fuse holder. I use this holder. The two parts go together with M3 sink head screws, I…
Modified this lift table to stick a piece of teflon plate on top for soldering support
Stand for A7 paper shiets I use as notes. The groove is slightly curved so the paper wont' collapse. The groove compensates the heigth difference from the angle and the curve.
The nametag for Peli 1510 Case I found did not fit my 1560 case I made this. It also fits the 1510 and 1535 Cases with just standing a little bit over the top. But you can still close the Case.
I recreated the eyelet to fit some 80x8mm carabiner clips. I also made room for a M3 sink head screw for screwing the shell parts together.
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. These boxes fit the inlay of my Peli 1560 that I will share in the next days. For the hinges use M3x25 mm cylinder head screws with two…
Sanding Block for paper with 94 mm with (standard roll with sold by local shops in germany). I mark this as a remix even if I had no particular model in mind while making this. But I sure took some inspiration from oter modells. Fits 4…
Neutrik NA style housing for USB to DMX conversion with generic converter board (FTDI clone). The shells hold the board in place while held together with the cover and an XLR socket. M3 sink head screws can used directly into the holes.
Modified the original from thingiverse for correct fit to the boxes I have ("KUKKO" generic set from amazon). No need to glue the frame to the box. Frame needs to be printed with support on print bed. Closed printing environment is…
I created this replacement part for the rack mount of my Korg Pitchblack Pro. The replacement is more rugged than the original so the tightening of the rack screws won't break it. Fit is quite tight but snaps in place like the original.
Simple USB-powered solder fume extractor with 12V fan. Fits a Noctua NF-P12, powered by MT3608 Step-Up-Module . I use these filter mats in there (need to be cut into shape). The design uses M3x12mm (4x) and M3x20mm (5x) countersunk screws.
For the conversion ot the electrics in my KR51/2L I modeled the housing of the original simson wire connectors. The connectors and mouting holes fit. Some parts have been strenghtened. More versions with more connectors or different…
Due to some problem fixing and rebuilding of my Simson mopeds (KR51/2L) I was looking for a better way to debug the ignition circuit of the M541-Engine with electronic ignition. I found the schematic posted by SSJ3 Vegotenks @…
I designed this adaptor to my Petzl Vortex helmet so I can mount my LEDlenser H14R.2 to it. It can also be used as a base for designing mounting brackets for all kind of stuff. The parts are connected with M3x20mm sink head screws and…
Code ring for color coding PowerCon cables for length. Fits Neutrik PowerCon 20A connectors. ------------------------------------------------------------------ Added version _XXA for the new Neutrik PowerCon connector series.
I created this housing for implementing an automatic OnAir-Light for DAW using this instruction. The front panel is printed with a manual filament change. I use a generic type-C AtMega 32U4 Board and WS2812B led strip with approximately…
Got myself some new drawers for my tools and materials. I bought some storage containers from Auer Packaging and designed this printable modular grid for them. I found some inspiration in one particular other model but built this one up…
Automatic sticker dispenser for rolls by 65x29mm. Carrier strip feeds down the front and back under for easy application. The two parts are mounted by two M3 sink head screws.
I created this EtherCon Housing that fits over several generic RJ45 connectors on cat cables. Very handy when the locking pin broke of ect. Can be printed in the orientation shown without any support.
Replacement for original tip saver for Benning Duspol and other similar testers. Can be attached to connection wire. Should be secured with 2,5 mm zip tie.
Upcycle empty Prusa Filament Spools as a small part storage for parts like screws or other stuff. Stacks up how high you like. The nuts press in to the hex pattern of the spool discs. Can be printed without support, overhangs will work. I…
I created this blade display for my Kenwood CookingChef food processor blades. The labeling is according to the numbers on the blades (the edges of the different blades don't have the same height).
I didn't wanted my Node to stick out in front of my i3 so I designed this holder that mounts to the original Prusa display holder with some M3 screws. The SD card adapter slides in right beneath the node.
Hanger for three/four scarves. Rings have an inner diameter of 60mm, the hook is 20mm with 13mm opening.
I created this pasta hanger using square chopsticks with 7.5 mm edges. Please make sure that it's mounted in a place so that nobody can get hurt by the tips of the chopsticks!
Color code ring for Neutrik Rean EtherCon connectors (and similar derivates) used on cheap ethercon cables.
Rack for tea boxes of brand Meßmer for mouting underneath a shelve board. It's a split design so it would be possible to get a middle part in between for expansion.
Small Box for most common backing utencils fitted to package sizes.
Mount for (generic) KVM switch. This is the one I got. Mounts with 4mm sink head screws. Print with front facing down.
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box containst end sleeves. These boxes fit the inlay of my Peli 1560 that I will share in the next days. For the hinges use M3x25 mm…
I created this rack mount for TL-SG1005P as a part of my Raspberry Pi Rack. This module fits DAP Audio 2HE rack cover . The insert is mounted with M3 sink head screws. The PSU is held in place by a special clamp (M3x5mm cylinder head…
I designed this printed spool core as narrow as possible without the need to cut the spool shells. If fits the prusa spools. Intendet use is for respooling smaller amounts of filament for long time storage and for storing cables.
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains up to eight USB drives for different applications. I used these USB drives. These boxes fit the inlay of my Peli 1560…
I created this storage mount for my Kenwood CookingChef steamer attachment to mount it underneath some shelves. For printing you'll need a printer with one axis bigger than 240 mm due to the size of the steamer.
Simple main jet injector holder for 8 main jet infector for BVF 16N1 carburettor for Simson moped. I use it for setting up my engine so I wanted to have some different main jet injectors with me. All 8 slots have M5 threading.
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains 4x AA, 4x AAA and 3x 9V-Cube. These boxes fit the inlay of my Peli 1560 that I will share in the next days. For the…
Every gigging musician and tech knows the issue … Drumkeys always going to disappear, especially when you hand them out to other people …
Breakout box for four DMX signal lanes from Cat-cable. This box is specifically designed for DMX (no shielding, only outputs) with 3 pin and 5 pin per signal lane. All locking hinges are flat to housing outlines. For assembly you need 8…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains some small drum equipment: DrumKey Cymbal proctection sleeve with some felt CymbalNuts These boxes fit the inlay of my…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains my Swissonic Basic Router (MK2). The router is secured with the lid so the antennas wont break. Beneath the Router…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains 11 packets of 5x20 mm fuses. These boxes fit the inlay of my Peli 1560 that I will share in the next days. For the…
I created this case for my H14R.2 head lamp so it won't accidentally power up inside my pack. The case is part of a set of cases I created for different stuff I use as an event technician. The lamp needs to be twisted 360° against the…
I needed some holders for my Weller soldering pins for my new WX2 soldering station. So I checked what was available and modified the existing designs I liked to my needs. WX does not need a magnet for standby detection so there is no…
I build this case for NeoTrellis M4 with 5pin midi output for a friend of mine to add more buttons to a lightning console. To date it runs a modified example programm from adafruit (midi-keypad). I'm working on a way to configure the…
During covid lockdown some colleague and myself built a soldering station for Weller RT-Tips based on an Arduino Nano. We took inspiration from different projects like this all around the internet but designed the PCB from scratch while…
I created this housing for RaspberryMatic with PoE-Shield with additional OLED display (generic SSD1306 0,91 inch I²C 128x32) and external antenna. To mount the RPI-RF-MOD-PCBA with the PoE-Hat you will need some stackable pinheaders for…
Big T had no power distributors with PowerCon input so I just created an inlay for rebuilding the power input.
Designed myself some cable tie rails for mounting my cables underneath my desk. There are many similar versions out there. Designed to me mounted with 4mm sink head wood screws.
I created this housing for a minimal size RDM/DMX-Splitter for my toolcase. The housing containst this pcba and is powered by USB-PD with 12V (I use these trigger pcbas). Due to size restriction the cables need to be soldered on to the…
Introduction I built this system out of technical curiosity due to all commercial available units are for one very pricy and for my knowledge all use 230V AC to feed the single units wich means that every unit has an internal voltage…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains my Swissonic Basic Router (MK2). The router is secured with the lid so the antennas wont break. Beneath the Router…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains some hearing protection equipment: Senner MusicPro for personal use Silicone Ear Plugs for handing out Generic single…
Cup for measuring one or two portions of (dry) pasta. Filled to the mark the cup holds about 125g of dry pasta, filled to the top is about 250g. We use Fusilli mostly.
I implemented the ESP32-Cam to my Mk4 and went looking for a mounting solution covering my needs. I liked the X-Axis Mount but I wanted to power the ESP by usb cable and also use the flash led as well as an external antenna. So I remixed…
Device to easy release small smt parts from their feeding belts without having them flying around all over the place. It's based on my SMD Boxes. Open the lid and feed the belt through beneath the lid, parts facing down. Thread the…
I created this headphone hanger to fold up when not in use. Mounts with four 4mm sink head screws. For the hinge I used a screw M3x30mm, a self securing nut and two washers.
For measuring smaller radiants with my calliper I designed this adaptor. Just align both axles to the radiant and measure the distance to the radiant with the thorn. The distance needs to be reduced by 10mm. For use in CAD tools.
I designed this stand for our four smoothie mixer bottles we store in a drawer. It prevents them from falling over. Also the bottles can dry completely. I added a version for six bottles with decreased spacing to fit a Prusa i3 style…
I created this rack mount for my RaspberryMatic PoE housing. This design is inspired by this design found on Thingiverse. This module fits DAP Audio 2HE rack cover . All parts are mounted with M3 sink head screws. The feet can be mounted…
I designed some 3D printed hinges to implement a cable storage in the cover of my flightcase rack. For the closing hinges I use these springs for some tentioning force. The distance between the rack front plate and the lid are 65 mm so…
I created this crown cap catcher for mounting underneath a mounted bottle opener on my IKEA IVAR shelve. It collects the caps and eather collects them or leads them straight into the trashbin. The hinge is mounted with some 4x20 mm…
I created a series of small boxes for holding stuff inside my toolcase I use as an event technician. This box contains an optogate . These boxes fit the inlay of my Peli 1560 that I will share in the next days. For the hinges use M3x25 mm…
Knurled disc with 3/8-16 unc threat for mic stands
Fitted to bigger USB PD Trigger module (23 x 12 mm)
I modified the Prusa Core One L toolbox by Kolka for better glueing. The interface is not just a slope but a groove and there are slots to fix the parts together for the glue to get hard with zip ties.
I designed this fan housing for useage in events, mounts on standard camera equipment with 1/4-20 UNC thread in the bottom. The design is based on the Modular Desk Fan 140mm by mirabatek. I used the industial version of the noctua 140mm…
To wszystkie aktualnie dostępne wyniki.
