Liczymy pasujące modele…
My late Mom's old Panasonic table radio needed its volume control (with integrated power switch) replaced. The replacement parts would apparently be considered vintage now, but Philmore sells an appropriate value pot with an integrated…
The bubble-pack these bits came in isn't a great toolbox carrier for 'em, and they're so small, they get lost very easily. This small sliding drawer box has a friction-stop when closed. It fits the Harbor Freight 61526 drill bits pretty…
I printed philthyfool's design, and it's nice, but the cap kept dropping out of it. I wanted a screw thread for positive retention, so I re-built it in Fusion 360, and added a screw thread (45mm outside diameter, 41mm inside diameter, 7mm…
Title says it all: Daughter broke the tab on the battery door, and rather than try and glue it, I made a new one. Plenty of trial and error… I used PETG at 90% infill. Careful with the support - gonna have to trim it out carefully if your…
Pretty straightforward idea: link your old and new shampoo bottles so you can get all the shampoo into the preferred bottle (which in my case is always the one with the pump, whether that's the old or the new bottle. There are two bottle…
UPDATED: I've re-created this in Fusion 360, and adjusted holes, modeled in screw-threads. Should be more robust, less prone to cracking or slipping. --- I made this mount so I could shorten my bowden tube, which in turn lets me reduce…
After replacing my monitor with a new one that didn't have USB outlets on the side, I spent a lot of time reaching under the desk to plug/unplug/replug stuff. I designed this mount in an evening to hold the ends of a couple USB3 USB-A -…
Set this up because I often find myself needing spacers for mounting electronics. It's handy to print a few of these to have spacers around. They print well - much better than individual spacers in a pattern. The matrix of the sprue adds…
Mount is similar (but not identical) to Brodit / ProClip 853359 and should fit same applications. I created with Lightwave 3D 2015, sliced in Cura, originally printed with black Hatchbox PLA (but moved to PETG after summer car heat…
The Realtek AMB82-Mini outclasses the typical ESP32 boards used for printercams, with a better camera and faster CPU, more reliable software and a more powerful and featureful board overall. After I added a printer riser with plenty of…
I'm using a dryer hose to vent cool air and fumes from my low-end paint booth to the outside, and needed a 4-inch tube to channel the air. I picked flexible dryer hose (which I think is only sold in aluminum in the US now). My hose came…
This rack holds all 8 drivers, in handle-size order from left-to-right. The slot is just a teense tight for the #3 Phillips-head driver. Would redo this if I could. Maybe your slicer can open it up just a little. 1mm should do. Note:…
One of our young flyers lost the motor retainer (in flight - exciting!) for the Estes Flash E2X rocket. The rocket isn't much good without the retainer, so I found something close on a 3D model site, then adjusted it to my needs with…
Designed this after finding many of the cheapest "bent-metal" type adapters offset the SATA pins by 1mm or more, meaning the drive couldn't plug into a backplane-style SATA arrangement, as used in my QNAP TS-119 NAS box. The installation…
I bought an Igloo threaded drain plug (Igloo p/n X000S9H40D) to add to my Profile II 50 cooler, and drilled a (~28mm) hole through the side and the internal drain plug boss before figuring out that the drain plug was too short. Oops.…
I modeled this before final assembly of my replacement LES tower frame. I'd happily keep buying the plastic replacement parts, but the shipping charge is brutal for such a lightweight part. I don't know how to print this. Maybe as my…
I created these mounts to provide a single solid semipermanent attachment to an airframe for an Estes Astrocam Universal. I didn't like the sort of taped affair that came with the camera. With the 40 degree mount and a front-surface…
I created this av-bay system for the nose cone on my 4-inch Mega der Red Max - a recreation of the Estes rocket. It has a robust hasp for taking a shock cord (though the pictured attachment is just a leash - my cone is rigidly attached to…
I use my bedside CPAP machine to air-dry my AirMini hose and mask after cleaning. This adapter makes it easy to hook the hose on so it doesn't leak or pop off. You may need a little tape (I use blue painter's tape) inside the adapter to…
These are the SMALL set knobs for the Lowel Omni Stand 01-33 (and apparently Uni TO Stand UN-33 and Uni-stand UN-33), to replace the knob-end of Lowel part number 7038. If you need the stud, it's kind of an odd bird. You can cut it from…
This deployment altimeter mount places an Eggtimer Apogee atop the 2.5-to-2-inch transition of the Estes Argent. To attach the mount, you'll need to remove the top of the blow-molded transition, and attach with small counter-sunk flathead…
The funnel takes one of three dimensions out of the problem, and provides a hole where two BBs can't get in an opposition arrangement that makes a clog. Not clog-proof, but quickly cleared. Keep the funnel clean of debris or adhesives.
These tubes fit the logic and clock tabs of the DigiComp I plastic computer. They're used to program it. I printed with white PLA. Note that the clock and logic tabs on the DigiComp I flip-flops appear to be a little non-uniform in size,…
I've had this great little handheld meter since not long after high school (longer ago than I care to mention). You see them pop up on eBay from time to time, and I've purchased a backup, but the latches on the battery door are a weak…
MadCow makes a great rocket, but some of their pseudo-scale birds need some tarting up, so that's what I did: I created a fairing, a blackout disk for behind the fairing, and a nozzle for the back. Makes the ramjet nacelles look a little…
The Estes 1/45 scale Little Joe 2 is one beautiful model, but it has its issues. Even if you've solved the adhesive compatibility problems, you still risk melting the plastic dress-up nozzles when you launch it. One solution is to remove…
Every stinking time I pulled solder from the spool on my iron stand, the roll of solder flew across the room. Got tired of it this weekend. This stand came with my X-TRONIC 6040-XTS soldering station, though I've seen the same stand…
After printing the Dirt Devil Scorpion wall mount (Thingiverse model https://www.thingiverse.com/thing:5931021 , pictured to the left of the brush), I needed a mount to hold the rotary brush that comes with the Dirt Devil Scorpion Plus.…
I really like my String Swing rack, but the guitars tend to fall over. (Perhaps I'm unusual in having mostly soft cases). To keep the guitars up, I created these separators. They're just a little bit tall for the crossbar - you could edit…
This jig helps you cut to length (slightly generous so you can trim/sand the bits) and assemble the LES tower for the SEMROC Apollo capsule as used on Saturn and Little Joe II models. The flat tower-side jig helps with a precise hold on…
I created this rack to make my soldering iron tips easier to manage with my X-Tronic soldering station. This rack holds 8 Hakko-style 7mm soldering iron tips, or threaded-insert heater tips. This rack has holes for mounting on the…
I created two sanding guides to help me either draw the parabola shapes (or ideally, sand the shapes) of the conduit ends of the MadCow 2.6in BOMARC. I then created an alignment guide to help position the ramjet cones when applying epoxy…
This digit readout panel and its associated 0 1 label should press-fit on the flip-flop panels of an original DigiComp I The digit readouts on my original DigiComp I were looking kinda sad, and rather than booger up the original part, I…
The MidiThru/4 splitter from Deftaudio ( available at https://www.tindie.com/products/deftaudio/midi-thru-1in-4out-splitter-pcb-or-a-kit/ ) is a really nice little kit, and about the cheapest real splitter box you'll find. However, it…
DigiComp I is an educational working computer in plastic, sold in the mid 1960s. My DigiComp I hadn't worked in decades because the plastic boss that holds the crank in place had split and broken - this is a part that takes a lot of…
I always do a rough job cutting machine screws to length with a hacksaw. This guide helps me position the blade for an even cut, protects (a little bit) the threads where I'm not supposed to be. This guide is for M6 screws 6.5in long. The…
I created this tether mount after a high-impulse flight destroyed one of my Mini TXes at liftoff by inertially pulling the board off the Kevlar tether I had looped through the PCB holes. Clearly, that was not the way to fly and I needed…
To wszystkie aktualnie dostępne wyniki.
