1731 modeli
NOTE Check out the improved version of the model at https://www.printables.com/model/574794 ! I like to stress-test prints that I don't intend to “keep forever.” I used organic supports for the two smaller pieces and brim on the elbow.…
Both pieces need supports . It should take less than an hour and a half in total. For the settings keep reading, for the story skip down below. The assemble it make sure all supports are cleared and slide the end without the ridges under…
This funnel has an outer lip and uses 16 magnets (4mm diameter, 2mm height) to hold onto the portafilter basket. It prints upside down without supports. Should fit most 58mm baskets. The bottom lip has a 70.2mm clearance, with a 58mm…
A propeller/wing protector for the inexpensive Drone Pro/E88/E99/E58 drone. This drone is a knock-off of the toy quad-copter, the “Eachine E58”. You can easily find this USD $20 drone on marketplaces such as Temu and AliExpress. Tested…
The Convair B-58 Hustler was a supersonic strategic bomber, capable of flying at Mach 2. It was made to fly high and fast to avoid Soviet interceptors. The B-58 was unlike other bombers, that begin it had no bomb bay or weapon pylons.…
Created a simple tool to help realign the piston on a Flair 58 manual lever espresso machine. I tested it on my Flair58 while fully heated and the tool seems to hold up fine printed with PETG, but use at your own discretion. Also works…
I was in need of a second Lily58 low profile keyboard so I order a new PCB kit but to my surprise this time it did not fit my old case. So I adjusted it to fit it flawless. with this new version the Keyboard is 0.4mm lower as the previous…
You can use this bottle holder to simply hang your bottles anywhere. Be it on a shelf, on a bar or simply on your table. Valuable space can be saved because you can now simply hang the bottles on the edge and do not have to put them on…
Here is a small pop filter for a Shure SM58 type microphone. --- It's probably not the best sounding one but it does the job, it's small, quick to print, easy to realise and in one piece. Update => The empty round version offers better…
A travel “case” to let you take your Lily58 on the go! Fits 3D printed cases such as Lily58 Pro High Profile Case , Lily58 Case with 7mm standoffs , and Lily58 Case Requires 1 Plate, 4 Legs, and 1 large rubber band
This is a wall mount for the Hitron CODA-4582 or 4680 (Rogers Gigabit) modem. The holes are M3 sized so M3 screws or #6 screw will work. Drywall screws fit as well. Print instructions Print using the included 3mf file or go simple and…
After printing, bend the inner part out slightly so that it can snap into place later. Printing in PETG 15% Infill 0.20mm Quality
This is an adapter to slave an ATN AN/PVS-14 with the Canon EF-S 18-55mm f/3.5-5.6 IS STM (typically included with the Rebel T7) and other Canon lenses. To assemble, remove rubber eyepiece shroud from the PVS-14 and place two halves of…
Cover für das Victorinox Mini, lasst bitte einen Like da oder folgt mir für mehr damit ihr nichts Neues Verpasst Danke MazZe_2880
Adapter for 58 mm dust extraction outlets (mitter saw, table saw, etc.) and Bosch Advance Vac 20 hose.
This is a simple dosing funnel for a precision (VST, IMS, etc.) 58mm portafilter basket. It has a wider mouth designed for filling the basket using a dosing cup either from something like a Niche Zero or a hand grinder. The lip that fits…
This part is designed to to hold a piece of foam or other material over the driver to tweak the sound signature. Installation: Press the part carefully on the driver assembly, (glue is not necessary). Printed with Creality Ender 3, using…
I purchased a new puc and coffee distributor for my Oster expressor machine. I needed something to hold the portafilter steady without making a mess and also to store it all afterards. This simple print will work for most portafilters…
Zahnrad mit 58 Zähnen für den Antrieb des Vorschubgetriebes an der Drehmaschine Bernardo P600G. Das Zahnrad wird anstelle des originalen Zahnrades mit 32 beziehungsweise 64 Zähnen montiert. Hebelstellungen und Gewindesteigungen sind aus…
The YIHUA 858D hotair station is shipped with different nozzle attachments. Mine came with “hose clamp” styles ( with screws). So I made this one for 3 nozzles, which fits on top of the station. There is space for 4 magnets d=8mm h=2.8mm,…
You may need to do some trimming around the screw holes to get it to fit right.
Redesign of the original 158mm drawers from https://www.printables.com/es/model/139570-fast-printing-modular-drawer-system-vase-mode made them ready to print no vase mode, with 2mm walls and an extra 10mm depth (recommend horizontal…
You will need for assembly: 2-4 studs m3 (10-15 mm) 2-4 nuts m3 3 brass spacers m4 (diameter 6 mm) 3 screws m4 30 mm if your original stand is lost, use this model…
A holder to attach a DIN rail to the back of a FritzBox 7583. The 7583 has a very odd shape with a big cutout in the back, making it protrude quite far from the wall. To reclaim this lost space and to better organize my Raspberry Pi…
Pele : 1958 alifabolaget Pele #635 Meh - so'so Playing card to 3d Plaque experiment. Upscaled trading card pic in img2img Stable Diffusion tiled depth in tilezoedepth google colab use depth for displacment use upscaled pic for displacment
Ice holder inside a fridge AEG SKS58840S0 Printed in PETG Please note there is a Right side and a Left side
These are two very small boxes out of the System 58 collection of sorting boxes. They can be used standalone for small items or they can be used with the smaller inserts to give them even smaller compartments. The sizes are: Nano: outside…
Da für diese Heißluftlötstation keine richtigen Füße mitgeliefert wurden und das Ding etwas wackelig steht, und, weil die Düsenvorsätze lose dabeiliegen, habe ich diese Basis konstruiert. Die Seitlichen Laschen krallen sich an den…
Replacement for the rear trailing arm support assembly. Compatible with Nikko 1/10 scale 4WD monster trucks from the 1980s-1990s.
Ermüdungsbruch der Einlegeböden der B/S/H Side by Side Kühl/TK Kombis einfach repariert Bei meinem American Side by Side Kühlschrank KA58NA70 04 von Siemens sind nach 10 Jahren alle großen Böden an den Ecken angebrochen, teils sehr…
WDT is an art. Its chaotic nature takes skill to master consistently. Umikot is a Tagalog word which means: to spin; to turn around; to revolve; to rotate; to circle; to go around; to swirl; to gyrate. In that spirit, this 3D printable…
Here is my take on the tricorder featured on the later seasons of Star Trek: The Next Generation. It has the option of being a standard science tricorder and can be converted to a medical tricorder using magnets to swap parts. Update log…
For the past year and a half, the Lily58 has been my trusted daily driver, delivering a gratifying typing experience. As the first mechanical keyboard I built, it holds a special place in my heart. However, most kits out there disappoint…
The Donut Espresso Shaker is an espresso shaker that enables even distribution when preparing espresso for a wide range of portafilter sizes. What makes the Donut Shaker special is that it achieves this result with any portafilter size…
You don't have a 3D printer but you need it? Buy on Etsy with Worldwide shipping → buy here __________________________________________________________________________________ IKEA spare part number 10087158 / 10082805 Fits only IKEA…
Use the pliers to separate the parts and then assemble the car. The model is on a scale of 1:64. To scale a model from 1:64 to 1:43, you need to use a scaling factor of 148.8% in the slicer Printing this model with multicolor produces a…
Please report a portafilter or other equipment that is not fitting, plus its dimensions. The tamper station features: holding the portafilter for preparing the puck (adjustable via vertical screw) storing two bigger 51-54 mm or 58 mm…
This model is compatible with the lego system.
“CM3588 NAS Case Desktop Standalone” - pretty much this.
This is a Lens Hood for a 58 mm Canon EOS Lens. Suitable for a focal length from circa 18mm
This model is compatible with the lego system.
This remixed part will serve as a replacement for the stock GoPro mount in order to provide a location for mounting 21x21 mm HGLRC M100-5883 GPS module on a SpeedyBee Mario 5 frame. GPS mount with GoPro v2: better fit and easier…
Mount (clip) for Shure SM58 and other compatible microphones. With 3/8-16" mount (for standard microphone stand) and 1/4-20" mount (for photo stands/tripods). Can be used with original screw and nut as well as any part can be used instead…
This model is compatible with the lego system.
This model is compatible with the lego system.
This coffee distribution tool is a copy of the OCD tool, for evenly distributing the coffee before tamping. It is adjustable and I made it so the 3mm screws can lock the internal adjuster/spacer in place. however it doesn't actually need…
Features No support Minimal filament 5g (54mm) 7g (58mm) Compatibility 54mm (untested) 58mm/58.5mm (tested on Decent Espresso and VST Precision Filter Baskets) Print Settings PrusaSlicer 0.15mm quality with 0.4mm nozzle
For those of you with ECM Manufacture coffee machines, here's a model of a tamping station or stand for your standard or naked portafilters. Best to do it in ABS or PETG as PLA may melt with a hot portafilter.
This model is compatible with the lego system.
This model is compatible with the lego system.
I am Genuinely surprised how many likes and downloads this model got, it is my most successful model so far thank you everyone I printed mine in Bronze-Colored PLA with 15% infill, brim, and supports everywhere. Be VERY careful when…
All informations are included in "manual" pdf BOM: 5mm carbon or glass fibre rod 4mm carbon or glass fibre rod a lot of m3 screws and nuts m3 inserts copper wire 05, 1 and 2 mm diameter and solder sailcloth How I Designed This Category:…
This model is compatible with the lego system.
This is a case for the awesome Commodore 1581 floppy disk drive replica project presented by toms01 on Forum 64 . The case closely resembles the original with some practical changes to make it more 3D-printable and to accommodate 'modern'…
A tamping station compatible with Lelit 58mm portafilters (PLA580*) for the Lelit Glenda and similar espresso machines. There are two versions, one is a simple tamping station with slots for the ears of the portafilter and the other is…
In honour of Pokemon Go's Mudkip Community day (July 21st) I have knocked up a Mudkip one piece and multi-material model Totally needs supports Print instructions Category: Creatures
This is a 3D model of a coffee distributor tool, perfect for ensuring an even and consistent tamp in your portafilter. The model supports both 53mm and 58mm sizes to fit different espresso machines. To assemble this model, you’ll need…
Portafilter Funnel for espresso machines, comes in multiple sizes. Features: Tamp through Prevents waste (Spill over) Sits properly no magnets needed! Works well in combination with WDT tool Easy to clean Beautiful Print instructions…
Chess Dubrovnik Set - mod easy to print Kingsize 3.86" (for a board with 58mmx58mm fieldsize) Chess #Dubrovnik #Staunton /////////////////////////////////////////////////////////////////////////////// The set - except of the knight - is a…
Requires supports. I consider this a work-in-progress, I have not printed it myself yet. I may make a 2-part version that is easier to print. #1319971112300 This person is illegally selling this on Etsy even though my design does not…
Niche Zero holder for Sage/Breville or La Marzocco 58mm portafilter. Designed to stylistically match the grinder while still seamlessly integrating the stock dosing cup and holder. It is an elegant way to grind directly into a portafilter…
The 3D model is a case for the Allium58 GLP keyboard. The keyboard is modified from Lily58 Pro. The bottom case can also be used with other plates with 1.2mm thickness. Parts to be printed Allium58 bottom case Allium58 bottom case…
split for smaller printers, may updated once the warbond is officially opened and i get a better view. takes a ½ in dowel Category: Props
2026.01.13 - Moved github links to codeberg. 2024.01.17 - Adafruit has a replacement for the main arduino board now. No code changes will be required, as the only change is to the accelerometer. The codeberg code doesn't use the…
This model is compatible with the lego system.
This is a Wallmount for your typical E61 Portafilter for the efficient organization of your Espresso stuff. Disclaimer: The original thing was shared by jimhigson on thingiverse under CC BY-NC 4.0 . I did reupload this to complete my the…
This model is compatible with the lego system.
This model is compatible with the lego system.
Please print with food safe filament like PETG. Matching neodym magnets: Shape: disc Diameter (D) 5mm Height (H) 5mm Tolerances +/-0.1 mm May not fit to all VST-Baskets. Please check the outer diameter, should less or near 70mm. (see…
This is a simple lens cover that works with lens hoods. There are two versions to the latch (58mm lens grip); v2 has a slightly deeper hold and slightly more aggressive teeth. I recommend printing the grip pieces at 99% scale width so…
Fun and easy to assemble. Comes with a Quick guide for assembly.
58mm portafilter funnel with a 15mm funnel wall. I found that 15mm was the right height to prevent grounds spilling while breaking up clumps without being too intrusive under the grinder. The slots should fit most portafilters, if they…
Stand or holder for your puck screens generally sized for 58mm portafilters. This was sized specifically for the Flair58 puck screens although may work for other puck screens of similar size. Flair58 pucks screens measure at 58.4mm dia…
Printing Any material should be fine --it's not designed to hold food items or be subjected to heat/pressure. I used PETG, but that was to match the filament I used for the tamping stand and portafilter dosing funnel, which are subjected…
This model is compatible with the lego system.
A simple lens hood for your CANON EF/EFS lenses. Prevent undesired glare, improve contrast in your photos, and add a personal touch to your camera gear. The stepped inner surface improves light-blocking performance. Compatibility This…
Simple opening and closing spanner for standard 4- or 8-ribbed lids of canisters between 1L-60L volume (DIN 45 thread, Ø48.2mm | DIN 51 thread, Ø58mm | DIN 61 thread, Ø65mm). Turn tool around or use the included insert depending on the…
I bought this DeWalt DCV580 at a thrift store with only the hose. I needed attachments and made these with a way to store the extras. Crevice Tool: Similar to the original and also clicks into the DeWalt handle for storage and will not…
A belt buckle style lens cap holder w/ a color change at the top. Holds my DSLR kit lens perfectly. Edit December 12, 2022: The standard version accommodates a 1.575" strap. I included a new version to fit 2.00" wide straps.
Uses any 1.5mm plate, including the 3d printed one here. Designed for the 3mm heat set inserts from McMaster.
This model is compatible with the lego system.
This model is compatible with the lego system.
Thanks to @trav_1593464 for letting me know that the holes for the pegs were left out of the original upload. The new 3mf has the holes in place. General: A model of the JASSM AGM-158 Stealth cruise missile by Lockheed Martin Why I…
Giant Lego Knife (x10 = 20.2cm) Print two part and two join Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.1 Infill: 15 Filament: Eryone PLA silk grey Category: Construction Toys
LEGO PART 85861 Plate Round 1 x 1 with Open Stud
WDT (Weiss Distribution Technique) is a method of espresso preparation to evenly distribute coffee grounds in a portafilter to ensure a more even extraction of coffee from the espresso machine. This tool uses several needles spinning in a…
Shure sm57/58 Microphone Desk Clamp Stand + Headphone holder. Don't forget to print the screw that is a separate file.
Check my FB group if you need more info after reading below. Again a riser but this time one which is in line with the outer lines of the machine. I have tested it with the X1C and the P1S and glass fits perfect. You will need 4 top…
This model is compatible with the lego system.
This model is compatible with the lego system.
Fits pretty much perfectly into the bestway flowclear pump model 58381. As far as I can work out, it is the Type I Version of the filter with model# 58093 which is 80mm in diameter and 90mm tall. Print two caps out of tpu and the inner…
Heavily inspired by rotf101's tamping-station (but created from scratch) - see "model origin" for link. I made this for my bottomless portafilter that come with my 2nd hand machine. I have a shades of coffee wooden handle that I fitted to…
A simple lens hood for your CANON EF/EFS lenses. Prevent undesired glare, improve contrast in your photos, and add a personal touch to your camera gear. Check out our growing collection of 3D printable designs for Photography ! Follow us…
Victorinox Rambler Knife Scales 58mm Beta testing: Also added scales that can hold two toothpicks per scale, because of the angles the tools do not fit flush. Category: Tools
Introducing a specially designed Tamping Station for the Flair 58 portafilter. Modelled for precision, this functional accessory ensures a stable and wiggle-free tamping experience. Recommended for printing in PLA, PETG, or ASA; other…
This model is compatible with the lego system.
A desktop stand for Lenovo laptops. Works with Thinkpad E580 and E480 so far, with a holder for the USB-C Thinkpad dock. Holds the laptop at a 30° angle, with the base of the screen roughly 15cm above the desk. Has small recesses…
I created for my Aurora Lily58 PCB Kit with MX switched from splitkb.com thie case. I used for the Oleds this Model: Aurora Lily58 Oled Housing PCB Hardware that I used Aurora Lily58 PCB Kit from splitkb.com with: RGB Underglow, RGB…
This model is compatible with the lego system.
![Chess Figure Set Dubrovnik [Kingsize 3.86"] - mod easy-to-print [for a board with 58mmx58mm fieldsize]](https://media.printables.com/media/prints/214964/images/1964918_1f7f8524-10d4-47f4-a17c-7be02bcff904/2022-05-27-20_52_51-window.jpg)
