117 modeli
/////////////////////////////////////// ENGLISH /////////////////////////////////////// Desk clock with ePaper display with discreet lighting and automatic time synchronization over WIFI. You need to print at least the front part and the…
Wydruk około 0,71 €–0,87 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Small case for this nice display . It may be a little tight, I had to sand down the PCB by a few tenths of a millimeter all around. I replaced the spacers provided by Waveshare by plastic ones with M3 thread and used a nut to fix it. When…
Wydruk około 0,09 €–0,11 € nettoWstępna wycena jednego wariantu
I didn't find anything fitting my use-case, so I took the excellent https://www.printables.com/model/427556-ahoydtu-gehause-case-dtu-ahoy-opendtu and https://www.thingiverse.com/thing:4738646 to combine into the above and give enough…
This is a low profile case for the 2.9" WeAct ePaper displays sold on aliexpress . It features retaining pins to hold the display in the correct position, and a snap-fit mechanism to hold the case together. The cable is routed out the…
Do rámečku dostanete ePaper (e-Ink) od Waveshare i Good display s úhlopříčkou 7.5" (170.2x111.2x1.25). Tištěno bez podpěr, 0.15 mm na vrstvu (QUALITY). Záda k přední části přišroubujte šrouby M2.2x5 (otvory jsou M2), stejně tak vývojovou…
Link to e-ink display: https://amzn.to/4080FCH Link to really good project for using the e-ink display: https://github.com/mendhak/waveshare-epaper-display This design has a relief area below the display so it can stand straight and not…
Simple housing for the newer Lilygo T5 4.7" Plus Model. The Buttons and connectors are at different locations on this one.
Wall-mounted case for WeAct 4.2" Epaper Module. Based off this 4.2" stand by napalmz and adjusted for WeAct module in place of Waveshare one. This model should fit WeMos D1 mini (ish?) ESP8266 board fairly tight. Pictured is a generic…
This is the 3D-printed enclsoure with a versatile retractable stand for the XIAO 7.5‘’ ePaper Panel, which is a energy-efficient smart home companion designed to seamlessly integrate with Home Assistant. Ideal for showcasing real-time…
A case for the 4.2-inch Waveshare Paper screen. The display is using Home Assistant to update the data every five minutes, in this case, data from a Weather Flow Tempest station as well as local rain gauge readings using the Environment…
Remixed low profile case for 2.9" WeAct ePaper displays sold on AliExpress, with hole at the bottom, for USB-C port (and not at the back, like the original model). Also slightly thicker than the original model It fits inside the display…
This is a remix of " WaveShare 7.5" e-Paper case - symmetrical borders " by ASW. Charging can be done via USB port without opening the frame. Additionally, a tilted version is available. Update 2024_10_09: Added the forgotten…
I was looking for a minimal and modern stand for the Waveshare 7.5" and found @Weaponsmith 's nice design. Cleaned up the model a bit and updated to hold a pi zero.
I designed this picture frame style holder for the TRMNL diy kit. It includes a stand to place it on a desk or you can hang it on the wall. It uses short M3 threaded inserts to mount everything together. What i used:…
Snap-Fit Case for CrowPanel ESP32 E-Paper (2.13") A precision-engineered, two-part protective enclosure for the CrowPanel ESP32 E-Paper HMI 2.13-inch . This design features a "sandwich" structure with a dedicated main body and a secure…
Case for the Lilygo T5 4.7 Inch e-Paper V2.3 without 18650 LI-ION Battery. Thinner overall than other models.
5. 11. 2023 - Přidaná verze pro nový LáskaKit ESPInk 2.5 Do rámečku dostanete ePaper (e-Ink) od Waveshare i Good display s úhlopříčkou 4.2" (91x77x1.18 mm - případně lehce tlustší). Tištěno bez podpěr, 0.15 mm na vrstvu (QUALITY). Záda k…
This frame is designed to be easy to print and use. It has a print-in-place hinge for the foot, which supports the frame, but it can also be hung on the wall, either in a vertical or horizontal position. I designed it in Fusion 360. I can…
I needed a case for my e-ink weather display project using a Lilygo T5 4.7" ESP32+Epaper and wasn't satisfied with the ones I found online so I made my own. Main features: single (reset) button integrated to the frame optional back cover…
Remix to remove logo from the frame and add spacious back cover since no back cover is provided anymore and the designs shown in the original are very thin and hard to work with. This is not a polished remix in any way, but is functional.…
School Timetable with ePaper display. Super easy setup. No soldering, no coding required. =) Functions Very easy to print and to setup device. Just plug all parts together and it is useable. =) WaveShare ESP32 powered 7.5” ePaper display…
TRMNL Desktop Stand – Waveshare 7.5" E-Paper Display This TRMNL desktop stand is a sleek, low-profile enclosure designed to display a Waveshare 7.5" e-paper screen at a comfortable viewing angle. It securely houses the Waveshare e-paper…
The model closes because it has a thigh fit. Layer height: Doesn't matter Infill: Also doesn't matter Material: I used pla but I don't know if you can't use other material
This is a remix from https://www.thingiverse.com/thing:5157668
Update 2019-01-08: Just before printing this myself, I changed the design of the screen mount from screw holes, to a 'shelf' because the screw heads prevented the lid from sitting close enough. I didn't realise that the flex cable on the…
I was unable to find a portrait oriented case for the Waveshare 2.7 inch ePaper display, everything I found was landscape oriented so I decided to create one myself. I also wanted access to the memory card without taking the case apart so…
Flash Adapter for SoluM ST-GR2900N / GR29000 ePaper Tags See the writeup on my Blog.
The ePaper driver board features a 24-pin FPC connector, a built-in charging IC for efficient and safe battery charging, and a JST 2-pin BAT connector for easy battery connection. It is ideal for creating WiFi-enabled digital photo…
A simple case for the Good Display GDEY042T81 4.2" 400x300 ePaper
Why use toiletpaper instead of Tissues? cheaper more sustainable (smaller in size per sheet) flushable conveniant because tp is always at home How to set up: in the future i maybe add a parametric version. Print both parts (customize or…
Remixed from original version. Here's the modifications: Taller version Ventilation grilles (ESP32 is hotter) Removed holes in the back panel (so no more stand) Create a D1 Mini ESP32 version (larger board) Print Settings Printer:…
ePaper display name tag with a 2.9" eInk display in offline mode held by 4 strong magnets to your clothing This case for a WaveShare 2.9" ePaper display comes with a small code to set 2 lines of text to it. With this code it can be used…
A simple display for the waveshare 2.9 inch pico epaper connected to a ESP32 (30 pin) with DHT22 temp/humidity sensor. Display I used: https://www.waveshare.com/pico-epaper-2.9.htm (Even when not connected to a pico I found it convenient…
Snap-together case (no hardware) for this board. Features a window for ePaper display, switch, USB port, and detents for the boards 4 buttons. http://www.lilygo.cn/prod_view.aspx?TypeId=50031&Id=1169&FId=t3:50031:3 My Github repo for…
Case for fitting an ESP32 C3 mini and a WeAct 1.54" epaper display for making a simple monitor that shows time, cpu and ram usage. No screws or extras needed. Github: https://github.com/konLiogka/esp32-system-monitor/tree/main
Epaper 4.2" Weact Pilot Dashboard weather station I understand my dashboard code and function may not be usable for you. But at least you may need my case parts. All the other parts have been bought from aliexpress and picked cheapest…
A simple housing for LILYGO® TTGO T5 V2.0 WiFi Wireless Module bluetooth ESP32 2.13 e-Paper Display Development Board…
A housing for a Waveshare 2.13 inch ePaper Display HAT for the Raspberry Pi Pico W. The Pico attached to the ePaper fit in the case tightly and won't move around once the battery holder sits in place. It fits 3 type AA batteries which can…
More about the project: https://github.com/clackups/draftling Part list: M2*16mm screws: 4 pc M2 nuts: 4 pc insulation tape (to fixate the battery and isolate the speaker) a piece of packaging foam to minimize vibrations Printed parts:…
(My display was cracked while testing an earlier version of this case with tighter tolerances - the current models don't have this issue. I have a replacement on the way but it'll be another month before it arrives. ) Designed with…
I really like MultiTricker's work and a project called zivyobraz.eu . But I wanted to put the display on a table and use it instead of a weather station. So I used my trusty onShape and I redesigned original frame a "little". :) The base…
I really like MultiTricker's work and a project called zivyobraz.eu . But for my 4.2" ePaper display I only had a 5000 mAh battery lying around. So I used my trusty onShape and I redesigned original frame a "little". :) And while I was…
The code for this project can be found on GitHub .
Pwnagotchi Case with WeAct 2.9" ePaper Display "Sources" of the Model can be found on OnShape: https://cad.onshape.com/documents/172fee915b4cc3dc319ceb2f/w/33094c145713f3fa30397bbe/e/763a9c2fd96bd14b04fed502
This is an enclosure for an AhoyDTU with ESP-WROOM-32 board and Ebyte E01-ML01DP5 transmitter. Since I couldn't find a case for my AhoyDTU with ePaper display that I liked, I designed this case. I was inspired by the case of…
Hide all the circuits behind this sleek display stand for an Adafruit 2.13" eInk / ePaper Display FeatherWing . Definitely recommend printing with supports. Attach your FeatherWing behind the stand with some nylon M2.5 Thread screws . You…
Poté co jsem vytiskl 5 různých zdánlivě pasujících háčků pro Skadis na které bych rámeček s ePaperem zkusil zavěsit jsem zjistil, že ďábel je v detailu a udělal jednoduchý funkční návrh. Tisknul jsem z PLA a dal 4 perimetry, takže už…
This is an enclosure for a 4.2" Waveshare ePaper display module. I've connected the module to an ESP32 and it displays a bunch of information above my desk. I put a rough guide to putting one of these together up on my blog. Print…
Wastepaper basket with holder for cupboard doors
This is a housing component for WeActStudio's 2.13in link labels, available on AliExpress . The front piece has a cutout for just the link portion of the screen, while the back piece has cutouts for pin access. The back half has 2…
Had a lot of CR2450 batteries from my ePaper tags that needed a temporary home This is a parametric OpenSCAD model - chose your size! update 2024-12: I renamed the model: it's of course for type 2450 coin cells (not 2405). Duh!
Print with 0.2 mm layer height, supports are needed only for the hinges. It holds together with the snap fit prongs, but it can alternatively be glued together using a glue gun if needed (for me it wasn't needed, the snap fit holds really…
A holder for a 2.9 Inch epaper display. These tags can be used at home to display information from a home automation solution. For example Home Assistant. More info on that in this thread: Anyone looked into using Electronic Price Tag…
ePaper display knob with a 2.9" eInk display in offline mode → no power needed. This knob-case for a WaveShare 2.9" ePaper display comes with a small code to set 2 lines of text to it. With this code it can be used in offline mode as…
This is a remix of my display frame for the ESPink board.
Rámeček vytvořený pro ePaper (e-Ink) od Good Display 10.2", konkrétně model GDEM102T91, ale pravděpodobně se vejdou i ostatní ePapery této úhlopříčky (vnější rozměr ePaperu včetně plochy okolo displeje je 224 x 157 x 1.0 mm). Pro uchycení…
Pozor - existuje druhá verze tohoto modelu, kde není potřeba tavná pistole ale “jen” se šroubuje: https://www.printables.com/model/546762/ V jednoduchosti je síla - do rámečku dostanete ePaper (e-Ink) od Waveshare i Good display s…
These displays are weird dimensions to frame, so I decided to 3D print a stand for it. Your display will slide in and there's a slot for the hardware attached to the middle of the left side of the display. There's a small attachment at…
These are 3 sizes of my Notepaperholder to ensure that your desk is always organised while still keeping the option to write something if you need to
Easy to print stand/holder for EPaper tag (about 14 mins) ST-GR16000. Read more about OpenEPaperLink here: https://github.com/jjwbruijn/OpenEPaperLink
2U 19 inch rack front panel mount for 3.7 inch e-paper and raspberry pi zero These panel mounts require the DAP 2U MP-1 bracket. parts used: 3.7 inch e-Paper HAT Ethernet / USB HUB HAT Raspberry Pi Zero W Print the front panel mount on…
This modified backplate is designed to improve usability and everyday handling of the TRMNL / XIAO 7.5” ePaper picture frame DIY kit. The modification allows full access to the control buttons and the Inkpad charging port without the need…
Adapter for the e-paper price tag to put on display in fridge in our hackerspace TkkrLab. Created by Mark Lendering Original on : https://github.com/TkkrLab/PriceDisplayAdapter
Housing for a 4.2" 400x300 eink screen as a weather station. The screen used is WeActStudio 3 color. The whole thing is based on the esp32 dev module.
The wall-mounted enclosure was originally designed for the TRMNL 7.5" (OG) DIY kit. However, as I’m working with OpenDisplay, the ESP32-S3 (XIAO EE04 board) is only partially suitable for battery operation. Fortunately, the XIAO EN04…
ePaper Screen enclosure and Raspberry Pi Zero holder. Parts List: Tri color Waveshare 1.9 inch e-Paper Module. (e.g. https://www.amazon.com/gp/product/B07P8LGGC7/ 20.99 USD ) Raspberry Pi Zero with headers ( 20.95 USD -…
This ePaper Breakout Board is designed for SeeedStudio XIAO series boards for allowing you driving ePaper display seamlessly. It also comes with a 8-pin 2.54 header for supporting additional microcontroll connections. Supporting plug and…
A holder for notepaper from HEMA. HEMA is a dutch chain that sells stationary, among other things. The paper sheets are 90x90 mm, the inside dimensions of the holder are 92x92mm.
Do not forget to print ePaper-4.2-BigBattery-back from original source it is not included here. Required materiel 1x M3x6 Hex flat head screw (or longer if it doesn't interfere with battery) 1x M3 hexnut 1x ePaper-4.2-BigBattery-back from…
Introduction This project uses displays a image on an e-paper picture frame. The picture switches once per day or controlled by the user. Included are the list of materials and how to build it. Knowledge Assumptions I am assuming in this…
Potřeboval jsem někam umístit jeden 5.65" displej, tak jsem pro něj vytvořil jednoduchý rámeček podobný tomu, co mám pro 4.2" modely. Seznam součástek: Good Display GDEP0565D90 5.65" 600x448 LaskaKit ESPink ESP32 e-Paper LaskaKit SHT40…
The mounting feet of the board need to be cut off for the board to fit into the frame.
https://learn.adafruit.com/ch32v203-eink-epaper-calendar-and-clock You will want to add supports for the display cutout.
This is a battery-powered frame for a 7.5" epaper display. I am using this for my ePaper Weather & Very Slow Home Video Player project . It can be hung on a wall, or use the included stand in landscape orientation. Use the rocker switch…
More Grasshopper fun.
Inspired by https://www.thingiverse.com/thing:1140638 - designed from scratch in Tinkercad to fit my own Kindle Voyager as snuggly as I could. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2mm…
Case with multiple mounting and battery options for the custom 9.7" display for OpenEPaperLink. The only required part is the front case. you have to align the display manually and fix it with glue. If you want to use the screwed on back,…
With my displaycover u can snap the 4.2" display in the frontside. All part snap together - no scews needet. More see in the PDF description :-)
Holder for a 2,66" ePaper Tag from Hanshow, Modell Stellar Pro-266R-N. But should also fit for other Tags in that size. In the thicker part you can include some magnets (but they need to be strong, otherwise it will not fix the holder…
Pogo-Pin-Flasher-Adapter für SoluM ePaper-Tags Dieser 3D-gedruckte Adapter erleichtert das zuverlässige Flashen kompatibler SoluM-ePaper-Tags. Er positioniert die Pogo-Pins passgenau über den Kontaktflächen und verhindert ein Verrutschen…
Simple ePaper case for 2.9 modules. The case has room for a magnetic badge holder, and the back can be removed for easy programming. STOP PRESS: I received my stick on magnets...if you install the plate inside, then there is not enough…
Just print flat on the bed, turn on support
This model was commissioned by Simon Méhat on Fiverr and is published with their permission. Thanks, Simon! Combined with OpenDisplay , this makes for a nice and discreet display to scatter around your home! Print instructions All models…
ePaper 4.2 Case for wallmount created with SolveSpace
⚠ I only tested this with a single frame, I'm not sure if Ikea places the mounts exactly like this every time!
Remix of the Case Cover to custom fit my desk shelf and provide some angle. 70 degree layed back orientation for better viewing, simply replaces the front of the OG design by Rafal Ko. (https://www.thingiverse.com/thing:5157668/files)
Original stand and front cover still fit, please get the originals there, or use the ones also in the 3mf i widened the usb hole (my usb port was on the side, not the middle) Now the board is flippable. And i adjusted the bar to fit the…
Very simple part to be printed with supports in “build plate only” Will work for many displays but original size is for parallel 9.7" 1200x825 You can adapt it just opening the .blender file Check Valentin Roland epaper controller in my…
Hardware required: 10.1 display fabricated by http://en.wf-tech.com sold by Good-Display dot com epdiy v7 parallel epaper controller (branch s3_lcd uses 40 pin, 16 bit connector) Any LiPo 3.7V battery Print base with supports, top part…
Holds quarter sheets of paper for notes, with stick-pen holder Category: Office
Mobile 12x smart home button panel with ePaper display. A mobile 1-click solution to smart home automation! Do you want so set your smart home lights, blinds, devices or work status to ”Home Office“-mode, or “Work Office”-mode with 1…
Case for a 7-inch eInk ePaper display. 640x384px. Any print settings. I used layer 0.2, nozzle 0.4, infill 15%, mounting holes for 2mm screws, 3-6mm long. hole for USB C socket 10mm
Holder/stand for e-paper price tag with integrated holder for aLi-Ion 18650 battery More info about project at https://www.klosko.net/blog/=clanek=epaper-samsung-solum4-2 (In CZECH) PCB with LDO :…
Siple stand for Samsung/SoluM4.2 e-paper price tag Project page: https://www.klosko.net/blog/=clanek=epaper-samsung-solum4-2 (CZE)
New version with 15 pin Sub-D cable Category: Electronics
E-Paper Weather Display — Case & Stand A desk weather station. The 4.7" e-paper panel holds its image with the power off, so there is no glow, no fan, and nothing to distract you — it simply looks like a printed card that happens to be up…
This is a display frame for a 4.2" 400x300 ePaper display, as well as the mount for a Seeed Studio EN05 or EE05 display driver board. This is heavily inspired by the cases designed for the Seeed x OpenDisplay display kits. To assemble the…
Nemo-De-Beun: Epaper Access Point Case Disclaimer: this project is experimental! Made in BambuStudios itself, adding negative spaces to a squarebox. Printed with an X1C, 0.4mm nozzle on the 0.2mm mode.
