523 modeli
An ethernet RJ45 repair clip with a snap lock that locks the plug in the socket. This model is optimized for sideways print so that the snap lock prints with the layer lines to increase the strength. Use: 3 perimeters (walls) supports To…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena jednego wariantu
Miniature Giants Causeway desk model. Print the base in green for grass or blue for sea. Recommended slicer settings Base: In your slicer rotate it to print upright on the long side nearest to rocks, see picture. This will give you the…
Wydruk około 2,05 €–2,51 € nettoWstępna wycena jednego wariantu
I recently got a Nokia 5G21 internet gateway from T-Mobile. The device is passively cooled and runs a bit warmer than I'd like although it never had any indications of overheating. I found a silent 120mm fan in my junk box and printed a…
Wydruk około 1,53 €–1,87 € nettoWstępna wycena jednego wariantu
This is a 10" mini rack mount with optional retention features. You can use the keyholes on the bottom of the device with M3 button cap screws, or the retention clip with a M2x8 button cap screw and M2 square nut, or both. Possible future…
Wydruk około 4,56 €–5,58 € nettoWstępna wycena jednego wariantu
Print 1:1 - PLA - module with designed interface of our other module (pin and hole) so keep the ration as indicated to fit into other modules or change ration to all of them equally. (More models on our Tinkercad, gradually we will upload…
Wydruk około 0,57 €–0,70 € nettoWstępna wycena jednego wariantu
A simple cable organizer when you really have to many cables to manage. The design is similar to what you can find in computer room (usually it is several meters in length and you cut it to size, but here we are limited to the print bed…
The Cloud Gateway Max gets hot! Do not print in PLA!
The only thing worse that the subscription model, are overpriced accessories that should have been included! I made this for myself, as I will only use it with a 2280. So, if you're are only going to use a 2280 too, have at it. Includes a…
Do pobrania Listwy Elektroinstalacyjne, do maskowania przewodów i kabli, listwy dodaję o długości 250mm i w następujących rozmiarach wewnętrznych: 1 . Wysokość 10mm i szerokości ( 15mm, 20mm, 25mm, 30mm, 40mm i 50mm) 2 . Wysokość 15mm i…
The step files is meant to be used as an asset in CAD software. But as it has a very simple geometry it can be printed in Vase mode. I added an optimized version for the vertical cover, cut in half and added an angle for the overhang on…
I didn't have room on mine to mount it up and down so I designed this sideways mount. It does not need any supports if printed in the orientation I have pictured.
Perfect fit for SKÅDIS mount for Ubiquiti Unifi Cloud Gateway Ultra. Does not block any I/O. Requires 2x Skadis T-Clip System - Low Profile Flush Mount Clips No support needed Printed with PLA with default setting
UPDATED: A simple cable management raceway / comb to help keep wiring tidy. Designed in OnShape, based on a common wire management product. Top snaps or slides on to the comb / bottom piece. They can be easily cut to length as needed. The…
This is only my third 3D print. I made the adjustments using TinkerCAD. I used PETG filament and an Anycubic Kobra S1 printer.
Simple wall mount for the Unifi Gateway Lite (UXG Lite). You can face the ports either up or down, but not sideways. “-wide” has a wide hole pattern that has the same width as the old USG Gateway wall mount, making this wall mount a drop…
These are simple 20x20 cable raceways to clean up any kind of wiring project. They have holes for M3 screws to mount to to extrusions or you can use VHB tape to mount to a flat surface. I have .stls for 90mm, 110mm, 130mm, and 150mm. I've…
Huge thank you to @kukynas for adapting the step files to the K1 Max Dimensions. As it has a very simple geometry it can be printed in Vase mode. I added an optimized version for the vertical cover, cut in half and added an angle for the…
A 10" 1U rackmount for the UCG-Ultra with three keystone slots.
This model was originally on Printables where the creator posted his .step file for editing. It's been mixed a few times but as the smaller Max and Ultra Unifi models. This is for the Unifi Cloud Gateway Fibe r unit. It's a wall mount…
it is largely based on Foden's design , which it also fits together with. I have also made a model for the Unifi Switch Ultra (USW-Ultra)
SSD tray to replace the original UACC-SSD-Tray
🇺🇸 Welcome to St. Louis! This model was created by Dany Sánchez . The Gateway Arch is a 630-foot (192 m) monument in St. Louis, Missouri , United States. Clad in stainless steel and built in the form of a weighted catenary arch, it is the…
The Gateway House is perfect for your fantasy RPG. It can be printed with no supports.
Wall mount bracket for Ubiquity Cloud Gateway Fiber (ucg-fiber). Gateway snaps into base and is held very tight. Exposes gateways ventilation slots. Slot to assist with removal. If you prefer to have a printed version of the model, please…
Remix of my previous submitted Xfinity XB7 Gateway Router for the new XB8. A left and right side model is included.
This is an M2 drive caddy for the for the Ubiquiti Cloud Gateway Max (UCG Max NS) with no storage built in. I printed this in ABS with 100% infill, just to have something for the screw to bite in to. I used a random pc screw i had lying…
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
Wall mount bracket for Ubiquity Cloud Gateway Max or Ubiquiti Cloud Ultra. Gateway snaps into base and is held very tight. Exposes gateways ventilation slots. Slot to assist with removal. I included another model “key” that can be…
The Unifi Cloud Gateway Fiber device does not come with a wall mount option like a lot of Ubiquiti's devices do. So this model allows you to wall-mount your UCG Fiber. It's designed to allow you to place the device in it with the cables…
This model is compatible with the lego system.
My version ended up a bit tight. Maybe it's because of ASA shrinking. Maybe because of the slight warp. But maybe it's just a bit tight. The screw holes are for M4 screws. I decided to mount the device with it's “top” surface towards the…
My Unifi Cloud Gateway Max sits on my desk. I noticed the aluminum bottom for heat dissipation gets rather hot. To help the heat dissipate and save space on my desk, created this small little vertical stand. One side of the stand I…
Remixed towilab's design to allow for access of the UCG max's SSD port. Made the L-portion of the ‘clip’ on the right side a bit more aggressive while removing the left side one entirely, allowing super secure retention despite only…
This model is compatible with the lego system.
I needed to store my angle grinders better and all the models for mounts I could find fit them flat against the wall, which takes up a lot of space that I didn't have, so I made some that fit sideways with the handle pointed out. There…
This is a matching shelf for Unifi Cloud Gateway Ultra. Fits with the lenovo tiny shelf, my TrendNet mod and my FritzBox mod. Printed with 10% infill and supports (slicer complains without, but I don't think there really are supports)…
Created from scratch to allow me to make my own rack mount. I wanted to leave gaps for the vent holes and potentially the storage bay too. I've taken all the measurements myself on a UCG-Max and while I've made every effort to get them…
Print recommendations: Print laying flat (not vertically standing up), as shown in the first picture. No supports Use double-sided tape, my favorite is 3M VHB.
A 10 inch rackmount for unify clout gateway ultra particularly stable Flat base on the front of the housing Integrated space for housing feet Precise fitting of the housing Clips to prevent it from being pushed out Printing possible…
A modular rack for pegboards with sideways orientation to save space. You can add the individual holder parts based on your needs: one big hole to hang a pair of pliers in, many small holes for allen keys, a small slot for calipers, ……
I designed a motorized gondola ropeway system that is compatible with the Skyliner models available at Walt Disney World resort gift shops. All required stl files, zipped audio files, and zipped vinyl cut files are included here. Parts…
Larger spacing in the bottom so the device can be mounted screen top / ports bottom. Printed in PETG, holds the device really well.
Mount Panorama Circuit, Bathurst, Australia, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
Overview This headphone hook holds your cans perpendicular to your desk, and beneath the surface to reduce the overall footprint. The clamp is fixed with a large printed thumbscrew to ensure there is a sturdy connection to your surface.…
Summary This is the one-size-fits-all repeater stand for all the wall plugged AVM Fritz!Repeater and FRITZ!Smart Gateway. All you need is a Euro plug extension cable. Compatibility list - all wall plugged AVM Fritz!Repeater (article…
A version that is larger than the standard cable raceway for more space
⚒ No 3D printer? No time to source components? I just opened my new e-shop where you can buy physical, ready-to-use versions of my models! Designed with passion, printed and assembled with care ⚙. 📦 Shipping across the EU: 👉 Get it at…
Engelsk: Mount for Ubiquiti Cloud Gateway Ultra (Unifi UCG Ultra) This mount is specifically designed to securely hold your Ubiquiti Cloud Gateway Ultra (also known as the Unifi UCG Ultra) in a practical and efficient way. With this…
Meshtastic or MeshCore Router/Gateway/Repeater based on Heltec Wireless Stick Lite v3 with additional components: LM2596 DC/DC Step-down Power Supply INA219 DC Current Power Supply Sensor BME280 Temperature, Humidity, Barometric Pressure…
This is my submission to the mechanical marvels contest. These components all work in design. However I have not been able to 3D print them and test them in the real world. I live in Mexico and don't have access to filament down here. I…
Dies ist eine einfache Führung, um das Filament bei einem Anycubic Kobra 2 Drucker an der Kante des Druckers vorbei zu leiten, wenn man die Spule oben montiert. Ich habe einen Spool-Holder gedruckt und montiert, um das Filament oberhalb…
A c-clamp style cable raceway / tray which clamps onto a desk to hide cables. It features a dovetail on both the clamp and the raceway so they interlock and remain parallel with each other. The screw threads through the clamp and press…
The latest mods from Ellie Valkyrie's garage! GUNS GUNS GUNS! More guns than any Freeway Flier can shake a stick at! Requires supports. If you like my work and want to see (and print) more of it, please consider stopping over at my online…
Designed this bracket to use in my Jonsbo D32 mATX PC case, but works with other cases as (see list below). The CPU cables provided with my Corsair SF850 power supply were relatively short and struggled to reach between the motherboard…
This is a new variation of my equipment box that I made back in March of 2020 for the Anycubic Mega I3 Mega. You can check out my older design here: https://www.printables.com/prints/33156-anycubic-i3-mega-clip-on-box This one is a bit…
This version is modified to be built on its side, with supports. A small amount of material was removed to ensure it lies flat. Placing it in this orientation makes it stronger due to where the layer lines form. It will not print without…
Quick Access Cable Raceway to organize your desk and computer cables. Can be screwed into a surface or attached using command hook/velcro/double sided tape. Very sturdy and easy to use. Printer Brand: Creality Printer: Ender 3 V2 Temp:…
Layer height: 0,2 mm; Nozzle 0,4; Material: PLA Depending on the print quality, it may be necessary to rework the sliding surfaces slightly with sandpaper. For a longer service life, a little lubricant should be applied. I hope you like…
Just a simple divider for sideways game card boxes. I specifically used these boxes and they work great. I have two versions, 69x94 is the same size as these official BCW dividers and 69x100 is what I used in the pictures as it forces the…
This model is compatible with the lego system.
Update 30.01.2026: Improved V2 released for better fit and less filament consumption. Summary This is the one-size-fits-all repeater stand for all the full-size wall plugged AVM Fritz!Repeater and FRITZ!Smart Gateway. All you need is a…
You're using a Makita or other Battery Adapter for your Dyson Vacuum and you wonder how to mount it to the wall now? Here's the solution, the sideway wall mount for Dyson Vacuums. Should fit most of the different Dyson models. With a…
As shown and discussed in this video: As described in the video, attached are both printable files and editable SketchUp files. This content was previously exclusively for supporters on Patreon, but I did not care for the Patreon business…
A small cable channel/raceway 18mm x 16mm used to hide and run a few small cables on the side of my lack enclosure. You can change the height once you drop it into your slicing software. You can also combine a bunch of these to make one…
Here are both possibilities in. Have fun. Print Settings Printer Brand: Anycubic Printer: Predator Supports: Yes Resolution: 0.2 Infill: 25% Filament: no information PLA ivory Notes: I have a Anycubic i3 Mega S. No Predator Category:…
Made a cable raceway with lid, 250mm. Dimensions, outer: 40x31.5mm, inner: 36x28mm. Print with 4 perimiters, 15% infill and no supports.
This is a mount to put a Unifi Gateway Max router into a mini 10in network rack. Print with the face of the mount down on the build sheet, rotated 45 degrees. Print with supports (I chose organic supports). No hardware required, unit…
Redesigned XB7 wall mount with additional support.
Wall mount bracket for Ubiquity Cloud Gateway Ultra. Gateway snaps into base and is held very tight. Printed on MK4 Layer Height: .20 4 Perimeters 15% or 20% infill (grid). I tested successfully with 15% infill. No supports needed Suggest…
Better Cable Raceways Having built my first Voron V0 I was very disappointed with the traditional cable raceways which came with my build. I also tried to print many other styles however I was always disappointed with them as the legs…
No curveballs on print settings for this one. Any layer height should work, but I print in .2mm. This model does require supports for the flanges that hold the UCG down. I use organic supports that I painted on within Prusaslicer. .F3d…
Wall mount bracket for the Cloud Gateway Max. The Max, unlike the Ultra, has cooling vents along the base so I simply added clearance for airflow.
I needed a wall mount for my Cloud Gateway Max's PSU so I made this. It's designed for the #6 screws I had on hand, but you could probably get away with another kind. The screw hole is 6mm. I printed mine in PETG for the extra flexibility.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
As I was building my IKEA Lack enclosure/stand, I needed a clean way to guide the wiring along its backside so, I designed these. I've since printed several of these and they're so handy. They'll be used in many more places in the…
Here's a model of Janeway's famous coffee cup that someone requested. The original prop was a Nissan thermal mug. Update log October 26 2024 - fixed the tag errors. October 12 2024 - Scaled the cup down to 80% size which is more fitting.…
This model is compatible with the lego system.
Added recess for Command Strip (small poster) mount. Added hole for mounting. Flattened section to create a “bottom” for alternate orientation while printing. Added friction “bumps” to the side to add grip for dongle. Note: Using this…
A cable raceway that can be easily adjusted using Fusion 360 Parameters. Parameters available: length width height screw hole diameter “screws every x” - create a screw hole every ‘x’ comb openings comb width - main comb opening width…
I am currently working on an Ender 3 Pro Switchwire Conversion, using the Enderwire design from boubounokefalos. https://github.com/boubounokefalos/Ender_SW After printing my printable version of the lower deck for the Enderwire, I had…
Partially enclosed shelf for a Shaw Fibre+ Gateway modem 2.0 (XB7). Also works for Comcast XFinity TG4482 / Arris. Printed with PETG, 20% infill, no supports needed. Suggest adding a cylinder modifier around the screw holes to strengthen…
Stack to allow you to manage your Cloud Gateway Ultra and Lite 8 POE switch
Watkins Glen, Dix, United States, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Bring timeless grandeur to your tabletop or display with this Grand Roman Triumphal Arch . Inspired by classical Roman architecture, this monumental gateway features detailed Corinthian-style columns, carved relief panels, and an ornate…
I took the USB Cable Storage Organizer for Gridfinity and turned it sideways
My son loves the Hot Wheels Super 6-Lane Raceway track, but he wanted to be able to race Hot Wheels monster trucks down it as well. I designed these risers for the finish line to lift it high enough for the monster trucks to pass…
Kobra Max Direct Drive uses the original OEM original extruder without buying another extruder allowing you to upgrade to direct drive. Plus, a cut for the cable does not get in the way of direct drive. You may need to get this cable if…
This is a bracket to mount a MeanWell LRS-350 power supply on it's side vertically. I designed this mount to be simple and conscious of the vent holes. The two brackets for one power supply are identical. it has countersunk holes for…
UCG-Fiber stand that raises the device a bit for better airflow.
Sebring International Raceway, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in different…
Snug fit which should hold the router in snuggly without needing to force the router in. SKÅDIS and screw mount variations available. Screw mount is designed for 3 mm screw. I haven't printed the screw version. Screw hole is designed with…
A wall mount for GL-S10 bluetooth gateway serving as an ethernet esphome bluetooth proxy for Home Assistant, remixed from the original AR300M wall holder with an additional BT icon inlay for fun Guide on configuring it as a bluetooth…
A Medieval looking door i designed to see if i like painting :). There are some more “door” examples available to download, i used these to inspire me. But.. i found the “to realistic” stones and planks a hastle to print with to many…
It could definitely be improved but so far it performs as well as the original on the other side. You can mirror it to get both sides. Don't mind the color change, I tend to use the last meters of spools for prototyping.
Road America Circuit ,Elkhart Lake, Wisconsin, USA, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts…
Tweaked the handle to hold an 8mm fiberglass driveway marker from the hardware store. This is a Remix of Collapsing Pirate Sword (Print in Place) https://www.thingiverse.com/thing:3597069 Thingiverse is broken so It won't let me connect…
Since Ubiquiti does not offer any wall-mounting options for their new Cloud Gateway Ultra. I decided to make this myself. Just print it flat on it's back, it does need some supports but nothing too crazy. Your CGW Ultra should just slide…
3D Printed 10" Network Rack Mount for Ubiquiti UniFi Security Gateway As part of my classroom network setup project, I’m building 10" 3D-printed racks for my students. They'll be configuring and testing real-world networks, gaining…
This is a low-profile cable channel designed to keep cables clean and organized. The slim design keeps cables hidden while staying discreet and easy to install. Currently included: Currently there's only the straight cable channels in…
Road Atlanta, Braselton, United States, on a stand with it's name. Race track 3x3 mm Stand 198x3x15 mm Gap for putting the track into the stand 0.1x0.1 mm bigger so it's easier to assemble. Looks best when separate parts printed in…
