47 modeli
There are many battery holders for the DJI goggle 2, but I always had the problem that the weight of the battery caused the strap to press hard on my ears. This additional strap holds the goggles in place and distributes the weight. You…
Print standing with support Improved my previous oculus quest 2 headstrap adapter: https://www.printables.com/model/578398-frankenquest-htc-vive-das-adapters-for-oculus-ques Some were already prefering it for quest 3, but now you have…
None of the adapters I tried had the proper curve to mate up to the arms on the Quest 3, so here's my attempt at one that's working well for me. There are two versions - one that needs supports (shown on the headphone jack side) and one…
I was not satisfied with the headstraps found here and there, I found it difficult to keep my mask on it while trying to put it on my face. Soooo... I designed my own, and it works like a charm :) The elastic stays on the strap! I made…
I made an elastic remixed idea from https://www.prusaprinters.org/prints/26330 But I design this for FLEX filament printing an d optimized design. I used Ice Filament FLEX which has high shore (== not so flex) This could be sterilize at…
You can use this to adapt a Valve Index Strap to the Quest 3. 2025-09-11 : I finally uploaded the Quest3 → Valve Index Gasket File with proper edits.
10 min print, replacement slimmed down display port cable clip- much easier to install and remove than the supplied pico neo 3 link clip. printed with cheps extra fast profile, taking just 10 minutes.
Why I have 3 different head straps for my headset and when changing I am most annoyed by the threading of the overhead strap at the top of the headset. So I came up with a simple solution. You'll need a little bit of velcro tape for that.…
A little thicker than the original as well. Category: Toys & Games
Attaches by taking off the 2 pads and the the top strap (which are all attached with velcro to the back) and then pulling ithe top strap through the loop that on the back-side of the 3D print. Then just attach everything back as it was.…
Hvaing long play sessions and party sessions with friends the original strap starts getting annoying and not really comfortable, especially the re-adjusting it to every players head for a good fit and view through the lenses. I saw the…
I love almost everything about my T2 and T3 headstraps (these are the Meta Quest 2/Quest 3 head straps with the hot swappable battery packs) from BinBokVR; the one thing that has bugged me about them though is NONE of the mechanisms that…
A lot of currently available headlamps share the same type of mounting on the headstraps. The mount consists of a couple rubbery rings that have to slip over the body of the lamp. This is ok for a one time task, but if you want to use the…
— MIGRATED FROM MY OLD THINGIVERSE ACCOUNT — Thanks to Jon Daniels for the Solidworks file. Just what I needed to fix my broken headstrap. Did a little reinforcement, but otherwise the clip fitted really nice. Link to his item…
I really like the SteelSeries Wireless Pro but it`s a bit stupid, that the headstrap is not adjustable. So in order to release pressure from my ears I created these simple adjustments that clip perfectly onto the headset hanger in order…
This is a mount for battery packs, specifically tailored to fit on the Devaso headband for the Meta Quest 3. It is fixed centered, ideally with strong glue or double sided tape. The dimensions of the battery pack holder are tailored to…
Broke my headstrap pivot and I couldn't find another for sale. This works great. I suggest printing with PETG and turning your temperature up about 10 degrees to ensure better layer adhesion. Be careful placing the part as too much force…
Attach your PSVR2 to the Meta Quest 2 headstrap for next-level comfort! This simple 3D printed adapter securely mounts your Quest 2 onto the Meta Quest 2 headstrap. Designed for the Meta Quest 2 headstrap and PSVR2 Snug, secure fit…
Inspired by https://makerworld.com/en/models/786993#profileId-724834 (or the orginal creator of this strap) I made one for the top of the head. I printed both of them with very flexible filament (Fiberflex 40D) and glued 13 mm thick soft…
A tracker mount for the Quest 3 BoboVR M3 headstrap. You can use superglue to attach the bolt to the printed piece and 3M tape for attaching it to the headstrap! You'll need this bolt: https://boltdepot.com/Product-Details?product=16061
I prefer wearing the goggles with an additional top headstrap, which is what this simple mount tab is for. For me, this increases the wearing comfort significantly. I reused the headstrap of betafpv goggles that I had lying around. I…
I was not satisfied with any of the existing options for counterweights (too obtrusive, inconvenient or unreliable to install), so I made a new system for my VR set. This one sits closer to the headstrap, making it less obtrusive. It uses…
This modifies the original model to both increase the cable diameter (and opening) to fit the thicker Kiwi design cable and modify the clips for secure attachment to the Kiwi design head strap. Print on side without support. Light infill…
Low profile/shortened buckle to use Meta Quest 2/3 headstrap with HDZero BoxPro I ziptied the strap pieces to the goggles and they lay flat when in the storage bag I didn't like the feel of an elastic strap, especially with the weight of…
On a photos TPU version of this adapter. I included non-TPU version but I haven't tested it. Inlcuded STEP files, feel free to experement. All original parts are in use except the “claw” thing you see on the 4th photo on the left.
Need: 2x M2 screws and 1x 2.5mm screw. All credit goes to cbutters Index strap audio may not work here, untested. https://www.printables.com/model/1125926-valve-index-to-quest-3-headstrap-adapter-set
My printed upgrade for the original Pimax 8k/5k+ headstrap. New Version here : https://www.thingiverse.com/thing:3903415 Updated orientation Now with headphones ! I used a cheap (about 10€) gaming headphone from AliExpress that has…
i have both the head and the cheststreap but this piece broke on me so had to allways be switchin this piece quick prints under 1h with ironing at 100%infill just as much fley as the original
Clips to attach the Sony ZX100 headphones to the kiwi design head strap.
Head strap for the Sennheiser 6XX series of headphones I made in about an hour after getting tired of the stock headband causing discomfort after extended use
The clips have been remixed to work with the DJI Goggles 3 without needing to remove the strap. I've also rounded some of the sharper edges that sit against your head in an effort to make it more comfortable. I remixed the strap to have a…
Small adapters that improve the comfort of the Pico 4/Ultra 🐇compatible with this one: https://aliexpress.com/item/1005009425156766.html
Unfortunately I don't have a photo of the broken band, but repair is quite straight forward: Cut the Band flush. Punch a pair of holes for the new flap. Use the clip as a reference. Mount the new flap. Secure with the clip, maybe use some…
A simple connector with M2 brass inserts to attach Headstraps for the DJI Goggles V2 to the newer DJI Goggles 2. The model can be printed with PETG or, even better with ABS or ASA for maximum strength. 8x M2 brass inserts are required, I…
just a remix of two designes from thingivers. a fan protector with a suport for the three bands headstrap. Edit: Tested it and works great! (soon some pics) Edit 18/4/18: one of the tow top braces for the head strap broke of becaus of the…
I wanted to create a pimax headstrap which would have more adjustment then the vive das & would allow me to use my own headphones. I took a headstrap from a broken psvr & created a headstrap adapter which has at least some adjustment on…
New version of my Audio Strap for Pimax HMD's. I used a cheap (about 10€) gaming headphone from AliExpress that has microphone dead for the speakers and foam. Could have been smaller but it actually fit with the rigid part of the strap.…
Helps holding the Conquest VR in place on that very thin BoboVR headstrap edge.
Hinges to adapt a Rigid Headstrap made for the Oculus Quest 1 you can find here : https://www.aliexpress.com/item/1005001562458200.html With headphones you can slide on it before installing to get sound. You can use those kind of drivers…
The Busqueda battery headstrap for Quest 3 comes with a clip similar to this, but I wanted an additional one to manage cables for an EyeTrackVR setup. This clip is specifically for the rear part of the headstrap, but could be scaled up to…
This is a very basic cord lock for the HTC Vive Deluxe Head strap. If you have one of the new HTC Vive, the triple cord is different from the original and tends to move and become uncomfortable as it constantly is touching your head. This…
The single large magnet is enough to keep the spacer attached, though not strong enough to carry by the loop.
Should work for all these models: BHP 7500 BHP 7501 BHP 7502 BHP 7503 Material 2x M3 bold with nuts
A little thicker than the original as well. Category: Toys & Games
Broke my headstrap pivot and I couldn't find another for sale. This works great. I suggest printing with PETG and turning your temperature up about 10 degrees to ensure better layer adhesion. Be careful placing the part as too much force…
Use this skull-cap in conjunction with my faceplate, for maximum comfort: https://www.printables.com/model/787545-quest-pro-style-meta-quest-3 This skull cap extends the DAS headstrap further towards your neck, so that it snugs better and…
