555 modeli
A half-shell case for the Galaxy Tab S6 Lite. Covers the back, sides, and corners. Also provides a bezel to protect screen when device is face-down on a surface. Hard shell design: Fills-up the MK3S build space (1-2mm to spare) Prints…
Needed some non-trip cable floor covers. Most coiled rubber covers do not lay flat, and silicone is too soft to protect cables from heavy downwards pressure e.g. electric wheelchairs. ‘Prusament Galaxy Black’ works well to hide dirt from…
Some time ago I published an adapter (see remix list) for using AA cells in place of C cells. That adapter works quite well in most cases, but I recently had an application that required a more ridgid shell. This new version takes longer…
This part allows a portable AC unit to be connected to a 5" rigid ducting pipe for external venting. My case was through a conservatory wall (UK) during a heatwave. Threaded side screws onto a 6" Portable AC Hose and the other side is…
I used the Triangle Labs Dragon Hotend v2.0. The hotend comes with m2.5x8 (4x) and m2.5x5 (2x) I use the m2.5x5 on the front and the m2.5x8 in the back. This is because the threads do not go all the way through the hotend so you need them…
This is a stubby nozzle for the RIDGID R01601K 18V Brushless 130 MPH 510 CFM Cordless Battery Leaf Blower. Use organic supports, but block supports in the inside section where the clip attaches. Print the clip on edge horizontally so that…
This is a part to make a connection between a Rigid shop vacuum and a 50mm ID hose. Specifically the size of antistatic hose that came with the Oneida Dust Deputy.
WHAT IS IT? This is a scoop holder for the Frigidaire Countertop Ice Maker model EFIC117. It doesn't come with one in the box, so this is my solution. Uses only approximately 3 grams of filament and prints in under 30 minutes depending on…
Multiple knobs from my Frigidaire drop-in range were broken in various degrees. Replacements are expensive, so I modeled this myself in Fusion 360 with measurements taken from a mostly working knob. I printed mine in ASA/ABS for heat…
Dewalt Orbital Sander (D26453) to Rigid vacuum adaptor. I added superglue to see if it would keep from snapping along the layer lines.
I like the idea and design of the SHOPVAC (50mm) CAMLOCK CONNECTORS WITH MAGNETIC CATCH by PeterH, but after printing it with PLA and 0.3mm layers, the hose connector and the male adaptor would not fit together. So I redesigned the male…
Overview: Tired of 2L soda bottles collapsing and crinkling in your self-watering pet bowl? DriftJug mini is the sturdy, reusable solution that won’t deform, leak, or look terrible over time. Designed to keep water flowing smoothly for…
A bracket broke in the freezer so I decided to try and print one instead of spending $50+ on one. I split the bracket in two because it wouldn't fit on my MK3S or Mini, but it turned out to fit on the Mini in two pieces. It's identical to…
So our newer Frigidair has a deli drawer that keeps popping out of it's connection to the sides when you pull it open (there's a pic of it like this) so I printed this clip to prevent that. I didn't need any tape or glue it just popped on.
This is a replacement for the Frigidaire 318242275 (Electrolux ICON) stovetop knob bases. Although the part you grab is metal, the base is plastic, and the knob post that connects to the stovetop often cracks at some point, and then the…
We made a diy tow rope for sledding/skiing/snowboarding in our backyard. Recently we upsized our rope from 3/4" to 1 1/8". The larger size required larger pulleys. Things started to get pricey scaling it up so went with hacking together…
These are fixes for the plastic parts that hold the handle. It is compatible with the Frigidaire Gallery series model FMT148GPB1, I'm not sure about any other. I've also included a larger bottom part (our microwave door's whole corner was…
CLICKbase , like the Clickfinity design it evolved from, is a latching Gridfinity baseplate that holds all Gridfinity compatible bins securely without using any magnets. The most significant difference with Clickfinity (and it's other…
The Rigid Molle Panel For Custom Organization V2.0 is a remix of my model Design software: SOLIDWORKS Slicer: Prusa slicer Printer: Artillery Genius Pro Nozzle size: 0.4 Resolution: 0.20 Perimeters: 3 PEI magnetic sheet Bed Temp: 60c…
I designed this Rigid Molle Panel For Custom Organization in SOLIDWORKS for the Printables Ropes, Cords & Straps Gear contest. Design software: SOLIDWORKS Slicer: Prusa slicer Printer: Artillery Genius Pro Nozzle size: 0.4 Resolution:…
AEG/RIGID Battery Mount \ Breakout You will need a couple of M3x10 bolt and nuts if you want to use the terminals and some of these connector + wire https://www.aliexpress.com/item/1005003770642780.html Updated new -…
Anka is a mostly 3d printed 1/10 RC Short Course Truck which is inspired and remixed from the excellent Tarmo4 project. (You may reach the Tarmo4 project's details from here .) If you are a terrible driver like me, this hobby might become…
This is a molle panel that has holes for screws and optional spacers if you do want to mount with screws. Holes are large enough for paracord and can be mounted that way too. it also has slits if you want to mount using velcro and straps.…
Another tactical rigid MOLLE Panel. I add some hole in the panel to set something with paracord or mini-bungee. And a lateral fixation hole to couple more than one panel. The 4X3 fit in a Ender3 with something like 18x19cm, and for…
This is a rigid mount for the BTT EBB3.6 v1.2 toolhead board on the ClockWork2 / Stealthburner. The plate is supported on three points and a lot more rigid than other solutions. It was only tested on a Voron Trident. No tests currently on…
This is a remix of figterk 's model to be able to use any rigid filament for those who don't have any flexible ones. I used the Gridfinity compatible model from DSwanlund for the dimensions. The bit holder fits right into the case, but…
This is a small, highly portable rigid heddle backstrap loom. Your first project can be a new backstrap, and you can use paracord, USB cable, shoelaces, or whatever you want to stand in until you have your newly woven strap. You'll need a…
I needed a phone case before the actual case arrived. I found Leo DIY's TPU case but I didn't have TPU lying around. I realized the dimensions should be similar. I just needed to cut a few notches to let the case flex enough for me to…
I lost my power switch key to my Tile/Wet Saw and decided to design one. I printed it at .2mm layer height with extra perimeters for strength. I stopped it at layer 3 for a color change and back to the main color on layer 5 so the text…
Rigid Battery Mount. Mounts to wall with screws. I printed it with PLA.
Rigid shop Vac Filter nut. This is remix from Dragonman57 from Thingiverse.
Easily printable cervical vertebrae with discs. Image segmentation made in 3D slicer. Other 3D works in Grasshopper and MeshMixer Same 3D model as Flexible Spine ( https://www.printables.com/cs/model/704103-flexible-spine) but intended…
The backplate is 2mm thick, so it won't cover the camera bump completely. Did that so it remains a bit flexible. It is kinda tight if you use very rigid materials, might be a bit brittle and hard to take off. # Print recommendations 1.…
The DF Loom is an extremely simple yet versatile version of a rigid heddle loom that can be built DIY-style at minimal cost. It uses 3D-printed parts and aluminum extrusions, which are readily available from local hardware stores. The…
Universal Impact Driver/Drill Bit Holder A universal cordless Impact Driver/Drill Bit Holder meant Instalation requires: 1 x Brand dependent screw ( check sheet below ) 2 x Neodymium Magnets 20x10x2 mm ( example ) Brand Screw Type Bosch…
Rigid NXT Shop Vacs already have a rotating coupler on the end with a locking attachment. I designed this to attach the Rigid shop vac to Dewalt DWE6421 and DWE6423 orbital sanders. This adapter has a feature that helps still utilize the…
Rigid Corner Brackets for 2020, 2040,4040 Alu-Extrusions with 6mm V-Slots. 2 different Designs: one for Corners with V-Slots on both Sides and one with V-Slots on one Side only. They are 20mm wide and 50mm long. Easy printable - just…
I picked up an older model Easy Weaver loom at a second hand shop, but it was missing quite a few pieces. They are generally made out of a wood species such as beech, which is hard to find around here. In addition, other woods hard enough…
Includes: - Outlet Adapter 90 degree elbow to Rigid 2.5” Vacuum hose (16 Gal. 6.5-Peak HP NXT Wet/Dry Shop Vacuum) -Inlet straight adapter to 2.5" dust collection tubing with band clamp -2.5" dust collection tubing to 1.5" vacuum port…
This is a bar for Frigidaire FFTR1821 door shelf. Ours broke after 2 years so I design a replacement. It's a bit deeper to reduce the stress on the bar when storing oversized jug (in our case soy sauce). Should fit 30" fridge with the…
I realy like the design of the ProtoXtruder HGX and just gave it an additional brace on one motor mount. Its almost no added weigth but stiffens the arm a fair bit. Remix of the great work of @nhchiu:…
I like it when I see the movement of gears and filaments. So, changing the front was just decorative. The back was made tougher, perhaps unnecessarily stiff. I also changed the tolerances for the gears a little bit. This design has been…
DJI Osmo Nano Lens Cap – Flexible TPU & Rigid ASA Versions (STL + Fusion 360) Description: This is a custom-designed lens protection cap for the DJI Osmo Nano. It’s available in two variants, optimized for different materials: TPU version…
Minimal, snap-on case for Pixel 9a designed for rigid PLA. Combines a 25% gyroid infill with 4 perimeters for flexibility and strength. Snaps on easily, stays on well, removes and reattaches without damage to phone or case. Prints in 1…
Remixed from another card holder to hold Semi Rigid card sleeves & Toploaders I printed a fuzzy outer edge on the top which was a nice effect On Prusa Mini print without skirt or it'll be too big
I needed a spool holder for the Rigid Ink 1kg spools as they have a larger hole (54mm) and wider body (74mm). This spool holder will hold a spool with a body up to 76mm. The Innofil/Ultimaker spools do not fit this holder, but it is as…
The original hardcase works great, but lacks a place for the stylus (S Pen). I've added a slot for the S Pen. The S Pen clips in best when oriented tip up. I've added the pen slot to both the smooth and textured version on the case. Only…
PLA material, 100% infill
Phone case for Moto g53 (2022). Was printed using PLA+ (didn't have any TPU at the time). If you choose to print in TPU just make sure to reduce the scaling in the slicer (doing this might require some trial and error). This is to ‘get…
The plastic ratchets that came with the original Kromski Harp Rigid Heddle Loom are prone to tooth slip and deformation under load. This design replaces the original pawl and gears with slightly thicker equivalents for better alignment…
This aims to improve print quality at higher accelerations on The 100 based printers that have larger build volumes. While the printed parts are now actually ~0.7g lighter than the v1.1 gantry according to the slicer, and the M5 bolts…
Couples two shafts rigidly by using a double headed collet with threaded nuts tightening both ends. Pretty simple, printed at 0.2mm height in PETg, 0.4mm nozzle, 25% infill. Had to add a 3mm brim on the collet to improve bed adhesion. The…
Another Rigid Hinge (heavy duty) for M5 bolts. Print in place as one piece. Works great in PLA and PETG. On PLA slightly smoother operation. Layer 0.2mm. x3 all perimeters, up & down. For dimensions advise file “Hinge_dimensions.pdf”
mayby some like them ;) BOM 16x M3x20 4x M3x16 4x M5x30
Use the default RatRig print settings recommended in this official link here . The .stl model has the correct oriented position on the build plate. P.S. Sorry, I only had stainless steel screws and no black screws.
I designed this adapter for my Kreg track saw for hooking it up to the Rigid 1-7/8 shop vac. I found a much better solution after that from Rockler but maybe this print will be useful to someone else. It fits the original twist lock…
SV08 bracket remixed
I had a sturdy result with the following settings: Nozzle: 0.6 Layers: 4 Infill 25% Mateial: PETG Supports: required I suggest printing the model facing down with a 45° angel. There is each a long and short version. Short or long…
a petg Cover for iphone 12, petg is best filament for this type of cover for iphone 12, a small and fit cover
The door bins that came in our ~20-year-old refrigerator gave out about 15 years ago. Frigidaire wants a whopping $55/ea to replace with an official Frigidaire part. But I am a 3D Printer! This design doesn't quite mimic the appearance of…
This is my cordless tool hanger for my Rigid 18v power tools, I refined this over many iterations to fit both old and new Rigid tools, they have changed a bit over the years, these are strong, use minimal plastic and have a screw hole…
This is a replacement shelf for a Frigidaire 241691311 refrigerator. It goes on the upper section of the door. The shelves that come with this refrigerator are an extremely poor design, and break almost immediately if you put any weight…
Description This is a rigid travel case designed for the ZSA Voyager keyboard. Magnets secure the keyboard inside the case and also serve as the locking mechanism. The case’s hinge is formed from M4 screws and heat-set inserts. A key…
I have updated the original model removing center pivot, making it rigid and potentially stronger and cut sharp corners to make them printable without thin walls I also added chamfers to the main body, print…
Modeled up the end of of the 1.875 shop vac hose for the purpose of designing tools for it. The threads on the end have not been tested but are modelled to match the best I could. Threaded and Unthreaded versions available + the F3D model…
Brigid the Celtic goddess of poetry Brigid, a prominent figure in Celtic mythology, is revered as the goddess of poetry, among other domains. Her name, meaning "exalted one," reflects her high status. Often depicted as a triple goddess,…
Thanks to @Kemmotar for the excellent design of the original. I made a few different sizes, and decided to put my Ender Extender kit to work. The result is marvelous. 30% Infill was used here, in Cubic Subdivision arrangement. I only did…
This design is an adjustable holder arm for phones, camera and anything else you want to attach to it based on modular links attached by ball join junctions and secured by a robust screw nut part. The arm is designed to be strong (even a…
Originally modeled in Tinkercad as a replacement for a lost hinge courtesy of my kids…. Printed in PLA, general, defaults are ok, supports recommended for pin. This should slide onto the hook built into the door, however, in my case,…
Used these magnets. https://www.aliexpress.us/item/3256804838997624.html?spm=a2g0o.order_list.order_list_main.23.25631802AjM3TL&gatewayAdapt=glo2usa
I printed it standing up with supports for the bridge
This design was published as a lazy quick fix because other options did not exist. There are better versions out there now, and I suggest you go check them out.…
If you find this thing useful, please consider sending a tip. Thanks! https://paypal.me/cdsmakestuff Dust Collector upgrade for Rigid Table Saw (model #TS3650) The original dust collector port attachment has only a 2.5" port for a…
I broke one of the drum latches on my Rigid HD NXT 6 Gallon Shop Vac that clips on the motor head. I was not able to find a printable part out there, so I measured and sketched up a functional replacement part in Fusion 360. Printed here…
The door shelves on every Frigidaire refrigerator Ive owned has broken in the same spot in the middle. This model helps fix that problem. Recommend printing with at least 3 walls and 20% infill. I printed in PETG as its a little more…
I suggest that you print the model with the back of the case down and with supports on the quad lock intreface. This case should be printed from a hard plastic such as PETG or PLA.
My wife needed a holder for various cylindrical shaped objects under our sink. Print sideways. Very sturdy. 100% infill / 3 contours. PLA or PETG Happy printing
A storage holder for your Sleeves, Toploaders and semi-rigids!
Nothing special. I just made a prototype in PETG. Update- Added a version 2 that allows the barrel section to be modular making the print quicker and cleaner. Also the tabs are offset to very slightly to allow only one direction of…
Multiple knobs from my Frigidaire gas range broke within two years. Replacements are expensive, so I modeled this myself with measurements taken from a working knob. The length of the shaft is 30mm. The outer diameter of the shaft is…
A imprimer en 0.2 avec supports Nécessite 2 vis M3x25 et deux boulons M3
Dewalt to rigid shop vac adapter
This is a remix of another model for a rigid heddle for a Brio or other toy loom. I altered it so it would have an extra hole and an extra slot, so you can use 40 warp threads instead of 38 (there are 40 slots in the beater on the Brio…
Rigid Table Saw R4514 Throat Plate. Original one broke, needed to design a new one. Designed with having the broken throat plate, but not the saw in place (ie: tolerances not yet tested when printed). Printed in ABS, 40% infill with tree…
AEG/RIGID Tool Mount If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. If you want to support my work buy me a coffee (PayPal). Thanks!
It fits model #LRA08PZU1. It increases air speed and direct the air at 45 degree angle. You can also use only the mounting bracket portion and design the duct by your self. This one fits right side duct only. You need to mirror it with x…
This is an adapter to connect a Rigid Shop Vac hose to a Dewalt miter saw.
super rigid upgrade that holds the 2020 alu profiles together to minimize flex, i printed them in PETG and they are definitely rigid The Machine isn't flimsy, but well, every little bit helps to be able to push the machine You might need…
I needed a hose adapter for my small Rigid 4Gal shop vac from Home Depot and couldn't find one, so I made it Printing x1c PETG: No supports Seam Position: random Layer: 0.2 Infill: 20% Wall Loops: 4
My original AEG 18v Blower attachment broke the clips off and kept falling off so I decided to design and print my own. I mean why not as that's what 3D printing is all about right? :D I designed this one 150mm long so you can have a…
Mounting: Print in the following orientation: You can usually fit 2 of these on a typical printbed. Printing in PLA is advised Make sure these hooks are supported. Use tree supports with the “on buildplate only” setting enabled:
I designed both the AEG/Rigid 18v Blower Round and Horizontal Nozzles to fit my custom designed and printed blower attachment but they do fit the original extension pipe. They may be a little snug at first but place them on and off a…
This version of the Ender 3 S1 Pro display stand removes the aesthetic geometry. This allows you to crank up the infill to make it even more rigid than before. I've also included the original CAD model for you to remix freely. Print…
Note that this is not the depth of the original shelfs. It is much thinner just due to weight concerns if I made it larger coupled with me not wanting to split the model to print on my 330X330mm bed. If you do have to to split the model…
Adapter to suck out or push air into PVC drain line with Rigid “shop vac." Female adapter for ¾ inch PVC pipe. Can hot glue pipe in to make a male adapter as needed. Process described here:…
For Imbolc coming up this February 1 in the north hemisphere, the ancient goddess Brigid's cross Update! Printed yellow 1/13/2023 scaled down to 75% and 'fixed successfully' with PrusaSlicer. Printed with ‘supports everywhere.’ The…
Use case: If you have a sander, you probably get annoyed at how much saw they produce, even wearing a mask doesn't help, especially if you do projects indoors even in a ventilated space. By using shop vacuum connected to your sander, it…
This is an old model I made on thingiverse, reposting it here with a pneumatic M6 thread option for bowden Also included STEP file ------ Support me on Patreon so I can make more stuff! https://patreon.com/squirrelf3d or buy me a coffee…
This is a wall mount for navimow GPS. You need the upper portion of the original pole. Of course you can use it for any other pole with 25mm diameter. Additional you need 2 M5x35 screws and M5 nuts. This mount is in 2 parts so you have…
