105 modeli
This is a simple enclosure to mount the OpenFFB TMC Motor Driver & STM32 Controller stack and provide some level of protection to circuit boards. Learn more about the OpenFFB project here: https://github.com/Ultrawipf/OpenFFBoard/wiki…
Wydruk około 1,56 €–1,91 € nettoWstępna wycena jednego wariantu
Both large and small dividers for the Ryobi Link SlotBox PETG suggested because garages/cars get hot Supports required Don't have a 3D printer yet? That's OK, order already printed from… https://jpelectron.etsy.com
Wydruk około 0,39 €–0,48 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A little case for the ST Microelectronics Nucleo-64 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…
The spacing between the holes in the bottom is 18 mm. There are three 2 mm holes for mounting the Nucleo board. You need mini screws like DIN 7981 2,2 mm x 6,5 mm. The holes in the bottom are 3.5 mm to comfortably fit M3 screws. Other…
A minimal, protective half-case for the STM32 Nucleo-144 development boards, with heat set inserts and screws.
A little case for the ST Microelectronics Nucleo-144 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…
For best effect print with PET-G (PLA is also fine, but the clips will be less flexible). Prints without supports. In the photo: NUCLEO-H563ZI
Slide cases for every 64 pin STM32 Nucleo boards.
Updated 07/09/2022 A bracket has been added for use on ikea skadis or similar murals. ********************** First I want to thank the user JAAANIK for his cool design "PARKSIDE X20V TEAM KSGER STM32 OLED T12 PORTABLE SOLDERING STATION"…
Great base by loco but I needed to throw it in my bag, so I created a lid for it. Two versions: one with text and one without. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 15…
Super-simple, minimal bumper for ST Nucleo F4* / Nucleo 64 MB1136 boards.
Included in the attachments is the parametric Fusion 360 design and the label design
The low cost bluepill board can be converted into a blackmagic probe, which supports JTAG/SWD debugging of many targets. To do this DFU/blackmagic.bin is needed, can be programmed onto the stm32 using serial bootloader or with an STLINK.…
This is a functional and aesthetic case for the STM32F429-DISC1 board. Gives access to all of the necessary GPIO pins/inputs, screen, and peripherals. The case is a 2 piece design with a bottom and top shell. Assemble with 4-M3x12 socket…
Updated : Added additional ribs for support. This is designed to have the short M3 heat-set inserts put into it. Personally, I use the ones from CNC Kitchen . I use M3 6mm socket head cap screws. This should work with all NUCLEO 64…
I just wanted a basic case for the STM32 Blue Pill board. I couldn't find one that was a basic case much like many of the other cases for similar sized microcontroller boards. It has openings for the jumpers, the button, usb and…
Hi, this is the case for STLink-V2 programmer which is part of STM32 NUCLEO boards (64 pins or 144 pins). The programmer can be separated from the board and used as standalone device. All available pins are exposed (SWD port, TX, RX, GND,…
Couldn't find any printable case for my new dev board, so I went to design my own. While doing it, I had to model the board itself first. This is a simplified 3D model of the new Black Pill development board with stm32f4xx (I got the…
A simple case for new black pill dev board (version with stm32f411x, should be compatible with stm32f401x, not to be confused with old black pill with stm32f103). No screws needed, top should snap on the bottom. Bottom holes should fit…
Watch the full video here : Check out PCBWay Here: https://pcbway.com/g/WQ1kw6 Waveshare microcontroller boards featured in this video can be found here: https://www.waveshare.com/esp32-s3-nano.htm?&aff_id=172582 My website with free…
High voltage curve tracer , isolation tester Some time ago I ordered 230VAC LED modules, consisting of an aluminium coolplate and electronics, separated only by a thin layer of isolation. I wanted to check the safety of the isolation, and…
Ein schnell gezeichneter Multitool Halter zum an der Wand befestigen des Makita Multitool TM30D. Könnte auch für andere passen. Hoffe ich konnte vielleicht dem einen oder anderen damit helfen. Die Löcher sind 3,5mm im Durchmesser und…
A half shell case for the ST Microelectronics Nucleo-144 line of boards. Check the list below for tested boards. Many of the cases today rely on screws to hold them down. With some of the later Nucleo boards there are too many components…
Description : This instrument has some useful functions for Arduino users. Besides being a voltmeter with data logging, it could answer questions like "how much voltage falls on the LED at 10mA current?" or "is this an IR LED or what?" by…
A very basic enclosure for a STM32 F401RE/F411RE board that utilizes a snap-fit to remove any need for screws.
I found plenty of mounts for Arduinos and PIs, but nothing for the STM32 Nucleo. So I made this. My board is the STM32-F446RE. It mounts to the 3 standoffs with M2 20mm bolts (18mm will probably do). There is space for a small breadboard,…
A docking station for your breadboards and nucleo 144 boards. The Nucleo board fits snuggly enough on the base, but you can secure it with heatset inserts (M3) and bolts, but be careful when screwing the bolts (M3x12) not to damage the…
Draufpressen und fertig. Material muss Hitzebeständig sein.
Teltonika RUTM30 DIN mount for following holder: https://www.printables.com/model/1453174-din-rail-bracket-58mm-heat-insert-screw-version
This is a case for the STMicroelectronics B-L4S5I-IOT01A Discovery Kit. It has cutouts for all connectors on the top and sides as well as for the integrated range sensor. The board itself has outer dimensions of 90.1 x 62.1 mm and a hole…
Software and assembly video here: Case is ideally held together by either melting with a soldering iron or just using glue. Electronics Used (Including Purchase Links) WeAct Studio STM32 Core (STM32F405RGT6):…
Case for the STM32MP157x microprocessor Discovery Kit, by STMicroelectronics. Freely inspired by the Raspberry Pi 3/4B+ Case by Stramos .
Thermomix Dough Tool - 1x for TM31 / 1x for TM5/TM6
A simply base to hold down STM32 Nucleo-64 development board. This way the bottom pins are not touching any surface (so no shortcircuit or scratching). Additional you can put it back into the cardbox and it should not arttle around. I…
Software and assembly video here: Case is ideally held together with 15mm M3 self tapping screws. Electronics Used (Including Purchase Links) DIYMore STM32F407VGT6: https://www.aliexpress.com/item/1005002186031065.html 2.42 SSD1309 SPI…
Overview This is a compact and lightweight case designed for Nucleo development boards. Key features include: Protective Top Cover: Features a latch to protect against dust, loose debris, and accidental pin bending. Safety Hinge: The…
This is a simple mount for the [initeq] STM32 ARM STM32F103C8T6 Blue Pill Minimum System Development Board. Needed one, thought I would share mine. Feel free to use this for anything. Contains 4 holes for mounting, using 3mm screw,…
Simple case for STL32. Case is FIT without tolerances, no screws needed. Two versions: open rails top open rails bottom (You can freely mix, to made it fully open or enclosed)
Marlin 2.1 Kingroon KP3S mks_robin_nano_v1_3_f4 STM32F407VET6
Summary This is a case for a EC Buying STM32H7 development board. The part number on board is FK723M1-ZGT6 V1.0. Purchased Parts The board was purchased from Amazon , but looks to be available on AliExpress, etc. as well. Qty 4 - M3.0x6mm…
This is building on top of the design from MikeyB from OnSteps forum. You can see the original here: https://onstep.groups.io/g/main/files/3D-printables/Board%20enclosures%20%28Cases%29/Max%20series%20cases/MaxPCB%20case%20by%20MikeyB…
Case with press-fit mounting for STM32 Nucleo-64 development boards. Print Settings Tested with Spectrum PLA, 50% infill, and 0.2 mm layer height. No support needed Tested Boards Nucleo-L476RG Nucleo-G474RE Let me know if it works with…
Als Ersatzteil, kleiner Deckel für den Thermomix TM31,
This is an enclosure I've built for my electric boat. It houses the electronics to read out the state of charge, cell voltage and temperature of my battery packs. A STM32 uses ethernet to interface with a battery management system via…
Small case designed with the STM32F405 feather board in mind. It has a button for the reset switch and a slot in the rear for memory card access. No provision for LiPo battery connector or I2C (yet). Also tested and working with Bluefruit…
Gobelet Doseur Thermomix TM 31 troué pour éviter au fouet de sortir de son axe pendant qu'il tourne
slight change from original removed bottom access holes (I don't need them, I access all gpio pins from the top, bottom is just allowing crap from the table to make shorts) had to cut of pieces of pcb support as on number of boards…
A simple and functional case for your STM32 Nucleo board with an embedded logo lid that clips onto the base. The board can either be simply placed inside the bottom part of the case or be secured in place with the included rings (XY hole…
34pin version of the 26pin case. Had to modify it a bit as the “Blue Pill” design seems to vary a lot. This case is 2mm taller to accommodate the USB connector plus a lower right angle jumper hole and larger top hole as the top pins are…
This is a simple STM32F429-DISCOVERY enclosure, without screws, just snap-in connections. Cack site is for dust sensor.
I wanted to add a BTT SFSv2 to my Sovol SV08, and needed additional pins to support both the motion and runout sensors than the SV08 mainboard supported. While there are alternative approaches (including wiring the sensor to the toolhead…
Arduino 39 keys keyboard with i2c interface for STM32, AVR or any other microcontroller with 3.3 or 5V supply. Size 4x10 cm using 6x6 mm tactile switches. The controller (Arduino Mini 3.3V 8Mhz) is dedicated to this application, and…
Little case for the 26pin Greaseweazle adapter board soldered to a STM32 "Blue Pill". Includes easy access all of the jumpers etc... so no need to take it out of the box. Top does clip in but I usually glue it for stability.…
Writer / reader for NFC storage system with cards of 144 byte capacity. Remember the days searching for your tiny SMD components with a magnifying glass. This is over. Type in the text you search for, hold the reader near the storage…
Ewrf e708TM3 30.5mm slot which can be mounted onto standart stack 30.5 x 30.5mm. Secure with zip ties. !!! DO NOT USE PLA !!! Print instructions Category: R/C Vehicles Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No…
Included in the attachments is the parametric Fusion 360 design and the label design
Added EXT mounting holes
Frame for STMicroelectronics evauluation board STM32H7B3I-DK.
Frame for STMicroelectronics evauluation board STM32F750F-DK.
Protect underneat your board while you work on it ;) See The OnshapeLink , Modify as needed.
I designed and printed a custom case for a STM32 T12 Soldering station as my previous setup was a lot of pieces. It turned out a bit bigger than i wanted but still quite compact. It is quite a bit smaller than even the smallest regular…
To mount a Nucleo board to this only M3 screws are required. The holes are 11mm deep, so with the Nucleo attached at maximum a M3x12 screw can be used. M3x6 or M3x8 is probably already sufficient.
Minimalist bumper designed for the STM32F407G-DISC1 development board. Initial insertion of the board is tight; slide the micro USB side of the board in first before securing the board under the two 1.5mm retaining tabs. Printed on Bambu…
I added some intermediate mounting plates to use original electronics with the Standalone version This is a remix from https://www.thingiverse.com/thing:398515 Category: 3D Printer Parts
This is a sleek and functional 3D printable case designed specifically for the popular STM32F103C8T6 development board, often referred to as the “Blue Pill”. Why you need this case: Whether you're using your STM32F103C8T6 for embedded…
Software and assembly video here: There are two sets of parts for the top+bottom+buttons depending on the screen size you want. Case is ideally held together with 12mm M3 self tapping screws. Electronics Used (Including Purchase Links)…
Mixraumverkleinerer Thermomix TM31. Gedruckt in PETG. Achtung! Darf nicht in den Geschierspüler :-)
This is a simple case for a MMDVM USB board created by N3XCC and sold at Repeater-Builder. http://www.repeater-builder.com/products/stm32-dvm.html Screw holes are not created yet as I am not sure how to implement them. I will update the…
Simple STM32 mount/support Adjusted to fit a STM32F103C6T6/C8T6 *53mm x 22mm (untested)
Enclosure for modified version of stm32 oscilloscope Remix of a firmware is here (STILL WORK IN PROGRESS, feel free to contribute): https://github.com/Kaminariss/STM32-Oscilloscope You have to use some sort of prototyping PCB, the one i…
I simple mount for an STM32F4VE that has a loop for a zip tie to hold the USB cable in place. Print Settings Printer: HEVO Resolution: 200 Infill: 15 Filament: Tecbears PLA+ Category: Electronics
KSGER STM32 REMIX FOR 2020 PROFILES. Designed for my original design of Multipurpose Arm and compatible https://cults3d.com/es/modelo-3d/herramientas/miltiproposite-arm Print in the filament of your choice: Filling: 25% Quality: 0.3 or…
Telescope OnStep goto controller Box for STM32 Blue Pill More info about OnStep goto controller on Howard Dutton project Box FreeCAD source on GitHup BOM additions 8x 2x6mm self-tapping screws 1x Small power ship type switch size 15mm x…
En las imágenes aparece una placa adicional que utilizo para adaptar la salida a cable plano flexible. Entre el radiador y el L6230 utilizo un pad termico. Los tornillos son de M3 rosca para plastico cabeza de allen.
A tray/holder for Universal Solder 's “Canaduino” STM32 Screw Terminal Adapter for Black Pill STM32F411CEU6 boards and similar. This exists so I don't accidentally short out proto boards on my excessively chaotic desk. Print Settings…
Ohne Stützmaterial druckbar auf der Seite liegend. Der Griff passt auf den TM3300. Bitte eine etwas längere Schraube mit Unterlegscheibe verwenden. Ich habe mit PETG gedruckt. Die Dichtung ist fester als die alte wenn man TPE druckt. Aber…
I needed a portable case for my soldering station do solder LED stripes on the go. I had a controller laying around and some 3S LiPos, so I came up with this design. You will need: KSGER STM32 OLED V2.01 Temperature Controller…
Nucleo boards are inexpensive, powerful development boards from STMicro for their STM32 family of microcontrolllers. Albeit they break out all the signals from 64-pins packages, they're unfit for an easy use with breadboards. This coaster…
This is a remix of the hand wired macropad VOID9 by Victor . Instead of the Arduino ProMicro this version fits a STM32F4x1 (aka "Black Pill"). I provide only the redesigned bottom part, please visit the original thing for the top pieces.…
No support. Just making sure print with the top upside down
Small solderless jig for USB access on the Echo Dot 3rd gen (2018, codename donut , model D9N29T). It holds three pogo pins on the TM3 / TM4 / TM5 test pads, so you don't have to solder wires to the board for kamakiri / TWRP flashing.…
I made a stm32 board mount to make it easy to mount on a sim racing wheel or use this mount to create any project. use: 4 m3x10 hex screw
If you want to wash your Thermomix Motor with Alcohol. For repairing of course.
STM32H747-Dısco Display Box
17/04/2026: Added taller top cover so it can be closed while wires are connected Magnets needed are 6x3mm and are friction fit into the organizer. The screws for the top cover are M3, length does not matter. The screws for the LCD holder…
Das Model verkleinert das Topfvolumen. Beim Zerkleinern von kleinen Mengen wird das Gut nicht mehr im ganzen Topf verteilt. Ich habe das Model mit PETG ausgedruckt.
This is a simple holding stand for the STM32L496 Disco board. It keeps it off the bench so things don't short out on the pins underneath.
This is a remix of the STM32 Mini12864 adapter cover by Voron Design to fit the boards sold by FYSETC with pre-soldered SWD headers. The STM32-Mini12864 module is used to replace the EXP1 and EXP2 ribbon cables with a USB Micro connector,…
This enclosure is designed for convenient and safe storage of microcontrollers. There are also grooves on the sides for easy handling with tweezers.
Angepasst an die Firewall / Router von Watchguard - XTM3x und XTM2x Drucke es auch gerne aus ... einfacher unter https://www.3dhubs.com/service/182243 ordern Category: Computer
Organizer made to fit: STM32 Microcontroller Case by Martin_Url https://www.printables.com/model/671138-stm32-microcontroller-case-b-l4s5i-iot01a Adaftruit half sized breadboard https://www.adafruit.com/product/64 Includes pockets for a…
Das Model verkleinert das Topfvolumen. Beim Zerkleinern von kleinen Mengen wird das Gut nicht mehr im ganzen Topf verteilt. Ich habe das Model mit PETG ausgedruckt.
Простой buttonbox на 8 кнопок и 4 энкодера. энкодеры ec11. кнопки 12mm. https://aliexpress.ru/item/32814739163.html?spm
This is really a "first cut" of a case to house an STM32F103 WeAct Studio BluePill+ development board. The design prints in two parts and can be connected together using a piece of 1.75mm 3D filament as the pin in the hinge joint. You can…
Half-case for NUCLEO-L552ZE-Q with breadboard pockets Tray for the NUCLEO-L552ZE-Q (Nucleo-144, MB1361) with pockets for a 400-point half breadboard and a 170-point mini breadboard. Hole positions were taken from ST’s PCB design files…
Made this stand because the board doesn't come with legs and has breakout pins on both sides. The user should still be able to connect to the breakout pins and USB ports. I have included the FreeCAD model in case you want to edit the…
Studenti dostanou možnost naprogramovat vlastní hru na předpřipravené výukové konzoli. Výsledkem je tak pro studenta funkční hra a pro vyučující multifunkční výukové zařízení.
TM3D is a Dutch manufacturer that recently changed to another spool type with a relatively large inner diameter. This bushing solves the problem to make it fit and spin free in the USS drybox. I printed it in PETG but any material will…
