Liczymy pasujące modele…
Spacer kit, good for use in electrical projects ( boards, mounts etc). Actual sizes Type Inner diameter Outer diameter Height variations M2 ⌀2.2mm ⌀6.2mm 3, 5, 8, 10, 12, 15, 18, 20, 25, 30, 40mm M3 ⌀3.2mm ⌀7.2 mm 3, 5, 8, 10, 12, 15, 18,…
A giant-scale version of the LEGO Flower "Plate 1 x 1 with 5 petals” (24866) piece from 2018, intended for use on the popular Giant LEGO Wreath . Interior diameter of the fitment is 30.0 mm; the same as the basic 1x1 stud piece. Redrawn…
You can buy these from me here! Consider supporting us on Patreon! These are battery holders that can hold (2) 18650/(4) 18350, (2) 21700, (2) 26650, and (2) 26800. I print these out of PETG for the toughness. My builds use a 0.6mm nozzle…
Just a few stands for the special events cards. I found that sitting flat on the tree they were harder to read. These keep the 66x44mm cards upright, but are small enough not to block the text. Any filament will do, and you will need a…
This is a high-poly replica of a red 1966 Ford Mustang modeled in Blender 2.8 and optimized for 3d printing. Enjoy!
A case for the Wemos D1 Mini ESP8266 PCB. It has holes on all 3 walls partially for ventilation but mostly for wire pass-throughs to make running wires in different directions easier. There are holes for the reset button on each side…
A sealable case for the NodeMCU ESP8266. Mounting screws hold in place while the lid snaps tightly on top and wont come off easily. This can be used standalone or as part of a larger project or design. This thing was made with Tinkercad.…
This model is compatible with the lego system.
OpenScad case for esp8266 development board. Thanks to Sergio Vilches for the rounded corners!
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
Fusion 360 source file available! UPDATE 27.03.19: Remodeled designs from scratch in Fusion 360 and added slots to fit full size dupont connectors as follows: V2 - similar to the original but with duponts V2_Hollow - hollow bottom, more…
This case allows you to put the dupont wires inside the case rather than outside (in case you have a cat that likes to knock your stuff around). It provides a bit more security to keep things from being disconnected.
This model is compatible with the lego system.
You will need neopixel stripes and a microcontroller. I used an esp8266 for wifi sincronization. I used 4 neopixel per segment to improve the color persistance. https://www.facebook.com/media/set/?vanity=Menyiques&set=a.10213457141085498…
Zentriering von 57.1mm auf 66.6mm in 10mm und 12mm tiefe Hub centric ring from 57.1mm to 66.6mm in 10mm and 12mm depth NEW VERSION ONLINE V2-→12mm V3-→10mm Gedruckt in PETG//Printed in PETG 0,12mm Qualität//0.12mm quality 0.4mm…
This model is compatible with the lego system.
Einfacher Wandhalter für 1-5 66mm Spraydosen. 12.06.22 - Adapter für 33mm Dosen hinzugefügt. Simple wall mount for 66mm aerosol cans. 06/12/22 - Added adapter for 33mm cans.
Basic mount. On the top mount the word "UP" should be mounted so it can be read properly. The clamps have a rounded corner side and a chamfered side, they match the mount part. You will need to rotate the spindle lock to make the mount…
Previously to everything else, if you would need an adpated Version, like different Panel Size etc., just DM me and i might adapt and add it. (TBD) Modded back pieces for Umbilical Passthrough (06.09.2024) Screwable Retainer Lid for the…
This model has been ripped from the RIDE 5 games files. All credit/ support should be directed to Milestone s.r.l. I cannot guarantee this model is printable/ watertight. Some repair/rebuilding might be necessary.
just a stretched version fitting ESP8266 nodeMCU v3 from https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/samwiseg0/esp8266_nodemcu_din_mount by samwiseg0
For better seating …. V2.1 Small Clamp has been reinforced
Hello friends this is a simple case the Node MCU (ESP 8266). Route the cables through the case bottom before you solder them to the Node MCU. Support is needed for the Case Bottom. Print Settings Printer Brand: Creality Printer: Ender 3…
It's made for the LOLIN D1 Mini v4.0.0. The case doesn't fit older versions of the D1 Mini with micro-USB or components on the backside. Video: https://youtube.com/shorts/DUVmJcQiBqA Buy: https://spacehuhn.store/products/deauther-d1-mini…
This model is compatible with the lego system.
*READ BEFORE PRINTING/DOWNLOADING* Volumetric Flow Test 200-660mms. Based off of my previous slower flow test. Use Soft Fever Bambu Studio. I use the same methodology from my Slower Volumetric Flow Test model to figure out flow, so start…
This is a head-base that can be used to build a puppet-, plushie-, robot- or a fursuit-head (costume). I did add some ventilation holes, that can also be used to attach fur. The lower jaw is movable. The ears are not included. Having…
This model is designed based on certain versions of the M72 LAW and has been modified specifically for 3D printing. As a result, there are differences in appearance and dimensions compared to the real one. The difficulty of assembling…
This is Guest 666 a giant creature with a dark past and with his best friend as Noob. Because of greed and other sins, he was transfomed by The Spectre into a enormous beast.
This model is compatible with the lego system.
There are 3 parts to this. The top, bottom and an accent colour board (for some extra fun). The design doesn't serve too much of a practical purpose (the hexagons look cool) but, the pins are recessed into the case to prevent them from…
This model is compatible with the lego system.
A highly visible (and in my opinion, super cool) set of wormhole tokens for use in Twilight Imperium 4th Edition. This is a multi-color remix of the wormhole gate tokens for Twilight Imperium 4 by Vypper on Thingiverse. Just set a color…
This model is compatible with the lego system.
Node Robot Platform using ESP8266 for robotic development. This project is inspired by the SMARS robot but use ESP8266 as it heart for out of the box remote control. Hardware Needed hardware (all the link is for reference): 1x ESP8266…
I was able to remix of the beer bottle helmet for FDM printing ( https://www.printables.com/model/236264-beer-bottle-helmet-insect-protection-bierflaschenh ) and I love the design, Now I was faced with the ban of glass bottles on my…
This is a really fun 3D 1966 Batman Logo. Easy to print in multiple colors using either a multi-material system or a slicer like PrusaSlicer or SuperSlicer to easily switch colors at each layer. Please contact us if you'd like to have…
Once again another awesome print from the 3DWarehouse https://3dwarehouse.sketchup.com/model.html?id=ufb4f2162-ecf7-47af-a6b0-0f4df5e2ddc6 There are still a few errors in these files that I was unable to repair. Ideal for some one with…
This model is compatible with the lego system.
This case has slight changes to it and is based off of Digital Juice 's. This update fits the LD2410 with or without dupont wiring and the USB C version of the D1 mini ESP8266. I included a text file of the .yaml file that is working for…
Key Features: Identification: The "ESP8266MOD" text is embossed on both the top lid and the side of the base for easy identification. Functionality: The top panel includes a rectangular cutout for a display (or pin access) and two…
This is left skirt which goes with https://www.printables.com/model/608317-btt-hdmi5-screen-mount-for-voron-24. Print Mirror for right side. Use skirt as per printer size.
Vertical stand for the Fritz!Box 6660 cable. Inspired by https://www.printables.com/model/43735-fritzbox-7590-stand If you have a different model check if it has the same housing. The diameter should be around 54.5mm
This model is compatible with the lego system.
6641 LEGO technic change-over catch
This is an adapter so one can use common 18650 LiIon cells instead of 26650 cells in a tubular receptacle. It should be printed in vase mode. I printed the one in the photos at 0.34mm layer height and 0.4mm perimeter thickness. The cell…
I took Shadowcraft's 1966 Ford Mustang Coupe model and combined the stls for easy 1-piece printing (besides the wheels). The body should print easily, though some supports should be placed under the front of the car. Then print the wheels…
Needs support to Print!!
This model is compatible with the lego system.
Case for multible ESP3266 dot matrix projekts. There are many projekts online, just search the web for ESP8266 and MAX7219 or dotmatrix. The drawer in the lid fits to the WeMos D1 Mini ESP8266 module. Close the lid with two M2.5 bolts…
There are many Buck Converter enclosures posted here, and none would fit what I thought was a common 1-button LED Buck Converter (66mm x35mm), which I bought on amazon. (…
I constructed this board to hold the above mentioned controller for development purposes. The part was printed with PLA with a layer of 0.3 mm. Any other filament works too. No rocket science. Step file included. F360-file on request. The…
ESP8266 node MCU V3 Case from AZ-Delivery
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This model is compatible with the lego system.
🧱Lego Duplo Plate 2x2 #40665🧱 RICORDATI CHE OGNI PERIODO DI GIORNI PUBBLICHIAMO I NUOVI PROGETTI (ANCHE LEGO) QUINDI ISCRITIVI,👤 SCARICA⬇ E LASCIA UN LIKE👍. REMEMBER THAT EVERY PERIOD OF DAYS WE PUBLISH NEW PROJECTS (ALSO LEGO) THEN…
This model is compatible with the lego system.
🧱Lego Duplo Plate 2x4 #40666🧱 RICORDATI CHE OGNI PERIODO DI GIORNI PUBBLICHIAMO I NUOVI PROGETTI (ANCHE LEGO) QUINDI ISCRITIVI,👤 SCARICA⬇ E LASCIA UN LIKE👍. REMEMBER THAT EVERY PERIOD OF DAYS WE PUBLISH NEW PROJECTS (ALSO LEGO) THEN…
It is a simple model of a 1966 Ford mustang with Magnum 500 wheels.
This model is compatible with the lego system.
This is a remix of an original terminal for a Wemos D1 Mini. Since I am unfortunately a total novice with regard to soldering, I was looking for an equally nice looking terminal, without the need to solder. I increased the depth of the…
Sony Xperia Z (C6602/C6603) Cover / Case Wide corners and near perfect fit. Has slightly overlapping face so the phone screen never touches surface when up-side-down.
As the Cable Fritzbox Modem doesn't come with a built in wall mount, i designed a simple one wich will do the job with ease. no special settings needed
A simple enclosure for Esp8266 board with 0.96 zoll oled display. Nedeed parts: four M2 screws wit the length 4 or 6 mm four inserts M2 inserts with 3.5 diameter and 3.5 mm height Print tips: no support needed print the lid with the top…
If you want to support my work, just buy me a coffee: paypal.me/predypavlovic Case for ESP8266 MINI D1 dev board No screws required Ventilation openings Can be mounted without unplugging the circuit board Includes housing with and without…
This is my case for the Wemos Lolin D1 mini v4 ESP8266. Please note that only the Wemos D1 Mini v4 fits in this case. This is my first CAD construction ever so feel free to make improvement solutions. Special credits go to my neighbour LS…
Print the two parts of the case without support and snap them together.
Support de charge pour montre connectée Nerunsa P66D Charging stand for Nerunsa P66D Smart Watch Impression à plat sans support.
A NeoPixel / WS2812b controlled LED Matrix with 16x16 Pixels Easy to print: Can be printed without support, Filament Type doesn't really matter. I printed mine with PETG, but PLA or something else should work fine as well! I printed the…
Small storage compartment for Aprilia Tuareg 660 that can be installed next to the lithium battery. Suitable for model year 2026. Maybe also 2025? Perfect for storing insurance papers (and some tiny tools). The box doesn't have any lid…
I tried all available clip designs and found that flyin_kapet's “Notch” version worked best. These are a simple revision of his design that doubles and triples the capacity. You do need to push the pellets into the center of the clip with…
This model is compatible with the lego system.
EN: This compact housing is designed for an LD2450 radar sensor with Bluetooth antenna and an ESP8266 Wemos D1 Mini V4. It is based on F-Square's multi sensor design , but is a new development except for the rear ball joint . The radar…
Note: Several of my designs for my CNC plasma rig are available here for free, and several others are exclusively for my supporters on Patreon that support for any amount, even if only a dollar a month.…
1966 Pontiac GTO Convertible. Another great car. This model was found over at the 3D warehouse. I have tried my best to repair the mesh errors, but it too still has a lot of errors to be fixed. Please re-upload it as a remix if you do…
Enclosure for a NodeMCU ESP8266 development board. The model fits boards with measurements being roughtly 26X49mm. The model is designed so that 5 Wagu 221 connectors can be mounted for connecting the LED-strip through a hole en one end…
DE Eine praktische hohe Rändelmutter oder Rändelschraube nach DIN466, Größen siehe Bilder Das Modell lässt sich ohne Supportmaterial drucken. Die 0,2 mm dicke Schicht lässt sich einfach durchstoßen. A useful high knurled nut or knurled…
This model is compatible with the lego system.
Remix of the great GAZ66 model of Pfelpensson, here with standard box used in different modifications for maintenance/repair workshops, laboratories, field kitchens, medical service and many other purposes. Model is hollow with holes in…
This is a set of dummy batteries, on each of: 18650 with button on top (yellow) 21700 flat top (green) 26650 flat top (white) 26700 flat top (blue) I use these to make battery enclosures etc. They are safer than using real batteries,…
Small snap fit case for the D1 mini footprint of the ESP8266. Reset button still accessible The small gap next to the USB connector can be used for routing cables to connect to external sensors Prints without supports
Junction box mount for v1 TP-Link EAP 610. It should work for the 620, 660, 670 or any other of the EAP models with the same mounting system. The included drywall mount for v1 EAP 610 didn't work for a single gang ceiling junction box the…
I needed an option to mount the Wemos d1 mini module of my OctoPrint-Monitor to my enclose and made this simple mount/case. It holds the module tight (but not too tight to aviod damage of the module), so it can't slip out. To insert the…
This mount is designed to attach an ESP-01 microcontroller to a krom schröder gas meter. It fits into the recess of the gas meter in which magnetic pulses can be read with a reed switch. In my youtube-video ( https://youtu.be/i9hPf0uNzFE…
This model is compatible with the lego system.
The small one is for the esp without the pins, and the tall one is for the esp with the pins.
1.3in OLED Screen case with ESP8266, used as stock ticker.
A template to drill the required holes to perform a shelby drop on a vintage Ford Mustang. Arrow points towards front of vehicle. If you don't know what this is for, you probably don't need it. This part was created based off of…
Gehäuse für ein ILI9341 TFT 320X240 Display Das Gehäusedeckel wird nur aufgesteckt. Das Display wird unter der Kappe mit 4Stück M3 X max.10mm Schrauben festgehalten. Das Gehäuse bietet genügend Platz um darin einen ECP32 oder D1-Mini etc.…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Rafts: No Supports: Yes Infill: 20%
09/17/22 update: If the wingnut continues to loosen when the spool spins, you can rotate the base 180% and flip the fishing line spool 180%. Or you can add an extra jam nut before screwing on the wing nut. After overpaying for 200yd…
This 3D printed Soviet-style GAZ-66 military truck features a rugged, nostalgic design inspired by historic off-road army vehicles. Perfect for collectors, tabletop gaming, war dioramas, or unique décor.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
UPDATE: Added a "Rugged" version with clips (pretty flimsy, take care) for an increased holding strength. A very slim case for the WeMos D1 Mini DISCLAIMER: I've designed this case to fit my WeMos board with very small tolerances. I hope…
I've tried to make a customizable socket to fit any module you are trying to Program such as the ESP8266 wifi module or a HC-05 bluetooth module. Prity much any module that is based on being a board to be surface mounted. The open SCAD…
![Twilight Imperium Wormhole Tokens [thing:4866300 remix]](https://media.printables.com/media/prints/317986/images/2777025_a621fef1-5cb2-4840-9242-7b7df00b92aa/pxl_20221120_190403314.jpg)
