Liczymy pasujące modele…
PLA is ok, I would recommend ABS because it has some flex. 0,2 mm Resolution 40 % Infill Tree-Support
This model is compatible with the lego system.
KTM 790/890 Adventure chain slack tool! Slide in from the back on the chain buffer till it reaches the front upper chain guard mounting point. It might fit the KTM duke. 38mm is how tall the actual printed part is off the chain guide. If…
Dyson Mini Turbo 967479-01 96747901 belt housing part T112750 supports needed This part was broken when the mini turbo brush of my Dyson V9 started to rattle I printed it in PLA and after a year it is still going strong Category:…
This model is compatible with the lego system.
este es un soporte para w702 de carpuride para montar la pantalla
Tool to help check chain tension and wear as instructed in the KTM 790/890 Adventure owners manual. The extruded side is 3.5mm thick (middle of the acceptable range 2-5mm) and 25mm wide. The bottom is grooved to check chain wear and…
30-40% infill is recommended. Bump up to 4 perimeters as well to fill the walls. Organic supports does make it easier to remove, but regular grid works fine as well. A remix of a model uploaded by Pavel Mironov on Thingiverse. The…
License plate holder for the KTM Duke 790. This design uses the stock tail light and aftermarket 10mm turn signals. Most 3rd party tidy tails use a non standard tail light and many of them are bad. I decided to design my own tidy tail…
I made this for the Worx landroid WG790 series, because the bearings on the originals were busted, and the wheel got destroide when i tried to remove them. Print instructions Category: Outdoor & Garden Summary I made this for the Worx…
I wanted to mount a 140mm fan to my BD770i for additional air flow. However, the included bracket only allows for mounting of a 120mm fan. This mount allows a 140mm fan to be mounted offset to the I/O shield and bolts into the existing…
A simple clamp that makes it possible to mount your phone in the center of your KTM Duke 790 using a SP connect mount. Just get one from here:…
Español Correa de repuesto para reloj Casio G-Shock G7900-A. Debido a que he procurado darle la forma de la correa original, necesitarás soporte para poder imprimirla correctamente, pero no supone ningún problema ya que serán mínimos. La…
A case for a PiKVM V2 (with functional audio). Parts list: Raspberry Pi 4 (any will do, I used 1GB) A power supply for the Pi, be smart, if this is running 24/7 be sure to get a supply that wont get too hot. Some female to female dupont…
There was a little gap between the mounting point and the Original GPS Mount (KTM Part Nr. 63512992144); this allowed the mount to rock back and forth, which slowly but steadily seemed to loosen the two bolts holding the mount. The part…
Quick mount to adapt the Quadlock phone mounting system to the KTM 790/890 Adv. The mount is angled downwards 5 degrees to better match the angle of the cluster. The long model works well with the vibration damper and a standard…
This dashboard cover is designed for the KTM 790 Duke . It protects the speedometer display against scratches, dust, and direct sunlight, while providing a clean look that integrates perfectly with the bike. ✅ Compatible with KTM 790 Duke…
This is a mounting bracket which fits the yaesu 8800, 8900, 7800, 7900, and probably others. When printed with ABS this is surprisingly strong (3mm walls probably help), but you will likely need longer screws than the ones you might (or…
Supporto cellulare RUGGED serie DOOGEE S99. (175mm x 18mm x 82mm) Questa versione è COMPLETA di gancio a molla per trattenere il cellulare all'interno dell'alloggiamento. Provato in off-road intenso. La molla è da cercare a parte in…
Required materials About 120g of filament (assuming 15% infill) - PLA is fine, but PETG / ABS is preferable 3 x 120mm fans (not every single fan will be compatible; take a look at the instructions for further detail) 12 M3 Heat Inserts…
This is the Standard Test Model for ASTM D790. Used for testing the Flexural Properties of Plastic. Its Dimensions are 12.7mm x 127mm x 3.2mm https://store.astm.org/d0790-17.html
The Minisforum ITX boards support an unusual hole placing for the cooler mounts, 52mm on the edges. The model by NAnglo uses a slighty wider spacing, therefore I needed to adapt it a little bit. Print with temperature resistant and robust…
Mounts a noctua 120mm fan to OEM minisforum 790S7 cpu cooler. Uses OEM screws to mount internal 4 holes to cpu cooler and M4 screws to mount fan OEM panel will also fit if foam seal is removed.
Handles for protecting front and back of the radio while also raising it over surface. Printed from PETG. Create opposite piece by mirroring object in slicer software. Glued 4x round rubber feet (up to 8mm diameter).
4.30.22 - Updated Dimensions of Mounting Bracket. The old version didn't take into account the total width of the computer, plus the sides. It was short by 20mm which was the wide of the front and back plates of the mount. Should be all…
I initially didnt even want to post it, as it was an easy design, but I came across 2 different cake boxes, where a clip was broken, so I uploaded it here. I noticed, that there were direct replacemts here for the clip, but they shared…
The model does not require any supports.
I wanted to optimize airflow for the BD790i inside my Fractal Ridge case. Played around with different fans and found out that the big NF-A15 and - even better - the newer NF-A14x25r do fit nicely in that setup. The new one even without…
Both mounting hinges broke, therefore, I made a replacement loading ramp for the shown flat bed trailer. Printing: Layer height: 0.12mm Infill: 100% Support: yes Orientation: same as STL Material: PETG Make sure that you get a good…
This is an adapter to mount a noctua 120mm fan (each version should, e.g. for me NF-A12x25 fan) to a minisforum um 790 pro. This allows for super silent operation. For the assembly first unplug the power supply on your minisforum. Then…
Philips Norelco Trimmer Organizer for MG7900 MG7910 I just needed a place to store and organize my Philips trimmer and all the accessories. This print holds the trimmer itself and all of the guards and extra pieces. I'm also including the…
Print and Play. I used my resin printer to make this. The two left ones in the photos are the new ones and the right one is the OEM version.
This model is compatible with the lego system.
This is inspired by Haprog's Model . I was lazy to install & setup Fusion360 for modification his files so I made this from scratch in other modeler. Based on your printer's bed size you can choose between 3 ( duo / trio / quatro ) models…
The impeller of our leaf blower/vacuum broke after ingesting a few too many sticks. With replacement parts no longer available, I attempted to recreate it by first modelling a slice of the part which I used to test the clip in blade…
You lost your HP workstation mounting screws? Just print 4 of these :D It's not perfect, but it works :)
Republishing a part that saved me some $$$ for my dyson repair. This design have been in my dyson since a year now and still working like new to this date. Thanks to Sulya for designing this one. *** Dyson Mini Turbo 967479-01 96747901…
KTM 890 Adventure has annoying issue. The hole in the rear mud flap does not make sense and just lets mud spray through and cover the rear light. This reduces safety even after light off road riding. it definitely needs to be covered. so,…
The motherboard comes with 120mm cooler mount, which may not be optimal for some builds. A 92mm cooler is the same width as the radiator. Hardware needed: 6 screws for mounting the brackets to the radiator, they come with the motherboard…
Needed this after removing the useless “Smartphone Integration” from my 2015 428i. This apparently fits many models and years. I originally intended to print this in TPU but my nozzle clogged mid-print. So went with PETG. The fit is…
Compatible with the Formd T1 V2.0/2.1 Configurations possible : 3 slot 3.25 slot I personally recommand you 3.25 slot to avoid turbulence noise. BOM : 1x M3x8 Countersunk screw 4x M3x5 Countersunk screw You need to install first the…
This is my third improved version of the dryer accessory. Whole model approx only 150g. Dryer 3.0 - Four quarters - better fit on the dryer. Version 3.0, you can stack them and dry several filaments at once. Recommendation: Layer height -…
Finding OEM parts might be difficult to find outside the U.S. therefore having a temporary option can be useful for KTM users of the 790/890 Adventure/Duke models (up to 2021). I created a 3D model based on the OEM Part 64112181100 and…
This design enables replace the original cover and fan with a much bulkier 120mm fan I had laying around (bequiet pure 120mm). As I connected m2 nvme egpu to the mini pc (k43sg), the cable prevented the original heatsink and fan to…
J'ai créer cette pièce pour ma moto car en France et Certainement dans d'autre pays, il est obligatoire que la plaque d'immatriculation soit riveté (pour quel ne soit pas amovible). Mais Ktm venant d'autriche et n'étant pas un pays ou…
Supporto cellulare RUGGED serie DOOGEE S98. Va montato direttamente nel vano predisposto della moto dietro al cupolino E' possibile usarlo sia con il cupolino in posizione bassa che alta. E' previsto l'uso di 2 dadi autofilettanti M5 per…
Ersatzteil für die Führung/Umlenkung des Powerbuttons im Gehäuse des ReVox B790. Das Originalteil kann mit der Zeit spröde werden und brechen, was sich dann in einem klemmenden Powerbutton bemerkbar macht. Das zweite Bild zeigt links die…
Takes 2 120mm fans and a single 80mm fan all 25mm thickness. Sounds way more bearable now at 100% fan speed and i get -5 degrees less on the hotspot. I used 2200RPM fans to better match the old fans. Link to the fan adapter:…
A stand so your computer can sit vertically without the risk of tipping over Might work with computers i have only tested M790Q Material: PLA Layer Height: 0.3mm Nozzle Size: 0.4
Bridges the gap between the fans in the Fractal Ridge and the GPU heatsink. Helps with focusing airflow directly over the fins of the heatsink, improving cooling. Requires deshrouding the graphics card. Compatible with Fractal Ridge case,…
This is a basic but functional 3D-printed bracket designed to mount a 120mm fan onto the ASRock RX 7900 XTX Phantom Gaming graphics card. My CAD skills are still a work in progress, so it’s not the sleekest design out there—but it fits,…
I needed a replacement battery cover for my Philips TV remote. The model I found for the OLED803 was similar to what I n
Desk platform for a Minisforum UM790 Pro mini PC with a JetKVM mount built in to help you organize your desk. The platform has divers that the UM790s rubber feet sit in securely, and a JetKVM holder to the right of the PC. On the bottom…
This is a remix of Robatzen's GPU Support Bracket to support XFX 7900XTX in my NZXT H510. If the dimension somehow matches perfectly to yours then you could just slot it in. Printed mine in PETG.
This is an adaptor for food dehydrator to allow it to dry filament while printing. It is compatible with https://www.printables.com/model/351745-dehydrator-to-filament-dryer-conversion-for-sencor so it is possible to have a filament…
lego 6990 73825 28974 4070 18986 87087 47905 26604 4733 3386 32952
Parametric buttons to easily customize the layout of your Kenwood radio's programmable function buttons. With up to 11 configurable function buttons, the TK-690, TK-790, and TK-890 are versatile commercial FM radios, that are easily…
Plate runner replacement for ariston microwave, suggested material ABS. You can isolate it from high temperature of food using a silicone or crock layer. Category: Kitchen & Dining
Quick and dirty remix of @nbss_198530 navi mount for the KTM 890 Adventure for Aoocci C6 Pro. Prototype printed in cheap PETG, with low infill, low perimteter/top/bottom count, still stable enough to not easily break it by hand.
Recently fit an android head unit to my 07 Lexus RX350 which did not work with the OEM reversing camera. The head unit manufacturer supplied an aftermarket camera however this did not interface with the OEM mounting hardware. This mount…
3mm hardware. 100% infill.
Use this deshroud mod to quieten your Sapphire Nitro+ 7900XTX. Uses 120mm or 90mm case fans for optimized air flow. I recomment controlling the fans via the motherboard trough "fan control", altough a gpu to casefan pin adapter might work…
PowerColor Hellhound RX 7900 XT Support for NR200 Case
Thanks for the great design! I used this design to make an insert for the Apache 1800 insert I created. https://www.printables.com/model/1345498-apache-1800-grill-insert The original model also fits the FT-7900r
Mimics Samsung PNs BN96-60953A or BN96-60954A TV Leg insert designs. Works on the 50", 55", 58", 60", and 65" models. This model has both a right and left model, as well as a re mixable adapter model (No Foot design). Re mixable Insert…
Technics SA-EH790/SB-DV290 Custom speaker grilles
If you are riding your KTM Adventure in Dirt you know that the side fairngs collecting quite some dirt. The uderlying casings for the tools suffer a lot and the rubber closings will fatique over time. Mine were broken after 2 years and it…
The mud flap on KaThy-M motorbikes has a big hole in it through which mud and debris gets thrown onto the stop light. I made this hole plug to stop it! You will also need some screws, plastic/wood thread with flat cap 3.5mm diameter, one…
mirror the STL to get 7700848790
I needed to connect my JetKVM and its DC power module to my Minisforum UM790 Pro, but the cables were always a mess. So I designed and 3D-printed a custom mount that sits on top of the mini PC. It keeps both the JetKVM and the DC module…
The Corsair 1000D PC case has a 2U PC slot that s vertically oriented. While it's not designed to contain a full GPU i liked the look of it. However, the support factor was an issue. So i designed and printed a custom bracket to support…
Magnetický držák pro fixu Eding 790. Použitý magnet 15x15x5
Simpler Halter des Wii SensorBars für "Philips 65PUS7906/12 65 Zoll LED Android Fernseher". Zum selber mit Klebeband draufkleben. Mit zwei Haltern auf der Rückseite für das lange Kabel des Sensors.. Einfach mit PLA in Schwarz (oder…
Super sleek minimalist design. If someone don't know what to look for not gone see at all. Design accommodate using 140mm fan on bottom and Aquacool Core reservoir mounted on radiator. Current model is only for XFX RX7900XTX MERC310 model…
Updated for rounded corners in the drawer and added space for a regular shaver.
My scout council used to use these older Marksman #1790 Biathlon pellet air guns, but the main seal started to get brittle and started cracking, causing loss of air and inconsistent results. No one seemed to sell them anymore, so we…
Material The part does not need to be flexible, but I still recommend PETG due to the higher temperatures around the portafilter. PLA may work, but long-term durability is not guaranteed. Orientation Two orientation options are included:…
Der Heckträger ersetzt das Originalteil der KTM 790 / 890 Adventure. Die seitlichen Handgriffe fallen weg. Das sorgt für eine schmalere, cleanere Optik am Heck. Es handelt sich um eine extra stabile Version (verstärkte…
Honda ST70 / CT70 Trail 70 Intake Manifold – K&N RC-0790 Pod Filter Adapter (34 mm Carb Inlet) A smooth-flowing intake manifold that lets you fit a K&N Universal Air Filter (part number RC-0790) to the standard Honda carburettor on the…
These are replacement feet for HP 16500 logic analyzers. I believe that HP also used these same feet on other instruments of the era. Printed using PETG (the feet require some flexing, and the first version I printed using PLA snapped).…
The ball-head adjuster was worn out on my bike and no-longer was holding the adjusting screw properly. This replaces the KTM part 61614019100. Print with 100% infill, 0.16 layer height and 0.4mm nozzle. PETG recommended.
I designed ink tray that used to hold ink bag for EPSON WorkForce Pro WF-C5790 and WF-5890 printer. Because replacement ink trays I found online are expensive.
After buying axle sliders for my KTM Duke 890R on AliExpress ( https://de.aliexpress.com/item/1005009783282434.html ), I noticed that the recesses were too large on some of the sliders, preventing them from properly aligning to the axle…
Steinbach 079030 Chlorine Dispenser Multi-Tool This 2-in-1 tool was designed to make the refill of the Steinbach 079030 chlorine dosage feeder easier. The tool combines two functions: Dispenser lid wrench: makes opening the chlorine…
Works on all motherboards with default screws. Recommended Thermalright TLB4020 2x Fans daisy chained with CPU Fan. This mod improved ram tempratures by dropping 10-15celcius. Which mad aggressive overclocking possible. Also fan hood…
Parametric buttons to easily customize the layout of your Kenwood radio's programmable function buttons. With up to 11 configurable function buttons, the TK-690, TK-790, and TK-890 are versatile commercial FM radios, that are easily…
Bridges the gap between the fans in the Fractal Ridge and the GPU heatsink. Helps with focusing airflow directly over the fins of the heatsink, improving cooling. Requires deshrouding the graphics card. Compatible with Fractal Ridge case,…
Takes 2 120mm fans and a single 80mm fan all 25mm thickness. Sounds way more bearable now at 100% fan speed and i get -5 degrees less on the hotspot. I used 2200RPM fans to better match the old fans. Link to the fan adapter:…
Technics SA-EH790/SB-DV290 Custom speaker grilles
The Minisforum ITX boards support an unusual hole placing for the cooler mounts, 52mm on the edges. The model by NAnglo uses a slighty wider spacing, therefore I needed to adapt it a little bit. Print with temperature resistant and robust…
Transform your Minisforum UM790 Pro into a Steam Machine with this drop-in solution. All with Removable Magnetic Faceplate Materials Minisforum UM790 Pro Mini PC 2x USB C M to USB C F Short Ribbon Style cables…
Mimics Samsung PNs BN96-60953A or BN96-60954A TV Leg insert designs. Works on the 50", 55", 58", 60", and 65" models. This model has both a right and left model, as well as a re mixable adapter model (No Foot design). Re mixable Insert…
Material The part does not need to be flexible, but I still recommend PETG due to the higher temperatures around the portafilter. PLA may work, but long-term durability is not guaranteed. Orientation Two orientation options are included:…
A minimalist organiser tray which holds the following Wera 8790 HMA Sockets: 5 5.5 6 7 8 10 11 12 13 I printed mine in ASA.
A minimalist organiser tray which holds the following Wera 8790 HMB Sockets: 8 10 12 13 15 16 17 18 19 I printed mine in ASA.
I remixed the original to enlarge the opening to hold the toothbrush. Made a little wider as the toothbrush is slightly rounded. Added a square cutout at the back. Added a slight curve to the front to increase the slight added depth.
Quick and dirty remix of @nbss_198530 navi mount for the KTM 890 Adventure for Aoocci C6 Pro. Prototype printed in cheap PETG, with low infill, low perimteter/top/bottom count, still stable enough to not easily break it by hand.
PLA is ok, I would recommend ABS because it has some flex. 0,2 mm Resolution 40 % Infill Tree-Support
A case for a PiKVM V2 (with functional audio). Parts list: Raspberry Pi 4 (any will do, I used 1GB) A power supply for the Pi, be smart, if this is running 24/7 be sure to get a supply that wont get too hot. Some female to female dupont…
I wanted to mount a 140mm fan to my BD770i for additional air flow. However, the included bracket only allows for mounting of a 120mm fan. This mount allows a 140mm fan to be mounted offset to the I/O shield and bolts into the existing…
