Liczymy pasujące modele…
Arris Surfboard SB8200 Rack Mount Enclosure I wanted to rack mount my SB8200 but in doing so and placing it between 2 pieces of equipment it would overheat as it is passively cooled. So I set out to design an actively cooled rack mount…
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000424 : Sun gear, 20 teeth, 0,85 modulus
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. E motor mount v2
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000430 : Planetary shaft (use 2)
===== CZ ===== Jedná se o kompletní krabičku pro převodník GBS-8200. Pokud stahujete mé modely, přispějte mi na vývoj pár korun. Vás to nezruinuje a mi to pokryje alespoň část nákladů na materiál spotřebovaný na testovací výtisky a…
Ersatz Gummipuffer Heckklappe am Megane 2 Coupe Cabriolet. Da dieses seid Jahren schon nicht mehr bei Renault verfügbar ist, habe ich selber einen Designend. Die Montage ist etwas unentspannt, da die Aufnahme sehr eng ist. Mit etwas…
Dremel support 8200 and other the pieces fit perfectly, if necessary give a little bit of sandpaper Print Settings Printer: Anycubic i3 mega Supports: No Resolution: 0,2 Infill: 20 to 100 Category: Machine Tools
GBS-8200 RGB to VGA Video Converter Board + SCART Case Remix adding housing for a SCART plug. This is the PCB mounted right angle version which clips nicely into the housing with the pins exposed so these can be attached to the wires as…
Will fit most Arris Surfboard Models (8200, 6141, etc). Complete re-design to fit the SB8200, re-measured, redesigned, and printed at least 10 different versions to ensure a nice fit on my own SB8200. Hopefully this fits better than…
Simply and fast printing wall / under mount for your Arris Surfboard SB8200 modem
===== CZ ===== Jedná se o kompletní krabičku pro převodník HCKJ-8200. Upozorňuji že deska HCKJ-8200 má trochu jinak rozmístěny součástky než GBS-8200! Proto i design je jiný, viz foto. Pokud stahujete mé modely, přispějte mi na vývoj pár…
Case for GBS 8200 VGA video upscaler with GBS control The housing consists of two parts that are screwed together. Power of device is taken from USB micro module and runs through a switch On the lid there are holes for OLED and encoder.…
This simple construction are for upgrading your K8200/3Drag to GT2 belt on X axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of X axis to GT2, you need:…
This simple construction are for upgrading your K8200/3Drag to GT2 belt on Y axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of Y axis to GT2, you need:…
Single piece hanger to fit a Ridgid 12cv lithium R82009 drill. Screws flush against wall. Quick and dirty design. I've not used supports, but my printed handles overhangs very well. As always, PETG is ideal for functional prints, but PLA…
This is a small rain cover for a eufy Doorbell 2K HDR T8200 with optional mounting wedges (15° or 30°). I glued the 30° mounting wedge to the rain cover with epoxy glue and attached it to the wall with the eufy mounting plate and 3.5x40mm…
Introduction I've been printing a bunch of ESRack things for my work and home racks and I've always wanted to rackmount these annoying cable boxes. Unfortunately they have a case that's almost exactly 1U high, so the standard ESRack…
My version of GBS Control case for GBS 8200 and two sizes of ESP8266 modules, plus RGBS BNC connectors. The two sizes of the ESP8266 module supported are: 48 x 25mm 58 x 31mm Please choose the corresponding one when you print. Project is…
Here's my rebuild of the X and Y axis of the Velleman K8200. It features GT2 belts, tangential clamping for the use of Igus linear bearings (Also works for normal ball bearings). It is way more sturdy than the original design and it…
You'll need: 4x 608 Ball bearings 2x M5x12 screws with corresponding nuts 4x M6x30 screws with corresponding nuts Print: 2x Spool Holder Arm 4x Spool Holder Spacer 4x Spool Holder Roller
This is designed/remixed to specifically hold the Arris Surfboard SB8200 Cable Modem and adjusted the pieces to reduce the flexing seen in other prints for this modem. Specifically, the tolerance causing the face of the mount to push…
40mm fan mount for the All-Metal E3D v6 Hot-End to Velleman K8200/3Drag standard filament extruder. Fan duct snap on reusing original extruder screws and spacers, optimized for robustness and easy print. The 40mm fan is more quit than the…
This model is a bracket to mount a Commscope (formerly Arris) Touchstone CM8200 Cable Modem to an IKEA Skadis pegboard system. This modem is commonly used by the Australian National Broadband Network (NBN) for Hybrid Fibre Coaxial (HFC)…
This is not a mod for the faint of heart, it requires an almost complete disassembly of the printer base frame. And probably a lot of swearing and frustration, but I am quite pleased of how it turned out. I am marking it as a work in…
This tool is a perfectly snug fit to safely remove fuel filter on a Kubota Loboy Diesel Generator and B8200 Tractor without damaging it. 3D PRINTING SETTINGS 0.15 100% Infill PETG
Like Bryan Crow I wanted to rack-mount my Arris Surfboard SB8200, but I don't have a full-sized rack only a 10" mini-rack. Since his model is designed to be assembled, I redesigned the front-plate to be a one-piece mount appropriate for…
GBS 8200 RGB to VGA Converter/Upscaller Box. Two holes at the back: one to allow for an alternate power cord (I use a USB power source) and adding the possibility of mounting a micro USB connector PCB; second hole for an input cable (I…
GBS 8200 RGB to VGA Converter Box extended to the right so it can fit a NodeMCU ESP8266 chip to use with the gbs-control custom firmware. Also room for a 6pin DIN sock and a switch which I use to turn off the CFW if required This was…
GBS-8200 RGB to VGA Video Converter Board Case with 6pin DIN & Wemos D1 Mini Wifi Designed to house the Wemos D1 Mini to use with the customer firmware https://github.com/ramapcsx2/gbs-control Cut-outs for all the connectors including…
Design After seeing Voultar's install video of this, I had an idea to make a housing for it myself, which was inspired by original cocktail arcade cabs. Video can be found here: https://www.youtube.com/watch?v=1AVXhiTlmgo Hardware Most…
I modified Modellaner's design. I aligned the openings in the front of the case for the Component RCA Jacks (and vga port). I moved the SCART Port as far back on the case as I could to help it clear the RGBS Header internally, so it…
A tray for the ICON 10 in. Pliers Wrench [58200] There are options for stackable and nonstackable with both small and medium tolerances, as well as basic non-gridfinity trays
An K8200 / 3Drag enclosure for the RepRap Full Graphic Smart Controller . It was my design goal to achieve a solution with as few components as possible and preferably without screws. In the design process, my goals were achieved, but the…
30mm fan mount for the All-Metal E3D v6 Hot-End to Velleman K8200/3Drag standard filament extruder. I liked the original fan duct and mount from E3D-Online and wanted the Hot End to mount on the original K8200/3Drag extruder using the…
This is a base setup to create modifications on this printer. I converted many parts from the OBJ model of http://www.thingiverse.com/thing:203292 but, many of them have been measured by hand. It have been made on Catia V5, aprx 20 hours…
This is a K8200/3Drag frame mounting clip with locking screws. It is based on my redesigned of the K8200 Frame Wire Clip On . Next step will be to use the clip in other designs there could benefit from the more secure frame clip. This…
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000425 : Planetary gear, 23 teeth, 0,85 modulus
Tweaked model originally from @Guybrush to have a SCART hole and LR audio holes.
This is a case with an 80mm fan mount for the Bigtreetech SKR V1.3. You willl need to get two M5x12mm screws to attach it to the K8200, four M3x10mm with matching nuts for the mainboard and four M4x8mm to screw the fan to the cover. You…
Spacer + T-slot block to mount things with 3 mm distance to the alfer coaxis 27,5 aluminium extrusions. Use M3 screws and nuts for the recommended M3 Version or 3,5 to 4 mm spax screws for the not recommended standard version. 2018-01-16:…
K8200 and 3Drag filament guide with one bearing. The parts can be printed, except for the bearing and the countersink wood/plastic screw 3x25mm. Update: Version for both bearing 6000ZZ and 608ZZ (skateboard bearing). The larger bearing is…
Edit 12/06/19: Added Pictures of the finished solution. I have been looking for a great way to make the Z axel go up and down. I have tried a DOZEN designs and none where what I was looking for. Now I have designed my own one and it is in…
Modified the design a decent amount to add a poe injector on the left side. Overall great idea as the arris takes up over 1U in its original case. Not sure if it sagged in the original design but mine definitely does so I may need to…
Simple K8200 and 3Drag frame snap on clips to hold the wiring as a replacement for the nylon strips. Based on BVD2e's model http://www.thingiverse.com/thing:444323 with few modifications. Update: Added variant with three profiles and STEP…
Hello dear maker! after a long search on thingiverse i've found this nice fan: http://www.thingiverse.com/thing:814286 . The problem i encountered was, that there wasn't any holder(for a K8200 / 3drag) for this fan at all! So i've decided…
Upgrade parts for the K8200/3Drag extruder to enable use of 3mm flexible filament such as NinjaFlex and TPE (shown in blue). Teflon tube in each part ensures a non stick filament feed. >> If you like it, please leave a like, rating or a…
The original kit has too much wobble on the Z axis, resulting in shifting and uneven layers. This design is for a minimal but rigid Z axis, using a trapezoid lead screw. There are only changes to the original design, where needed. The new…
This simple construction are for upgrading your K8200/3Drag to GT2 belt on Y axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of Y axis to GT2, you need:…
If you are using the 16T GT2 pulleys on a K8200/3Drag The belts will collide, and the Y belt will rub on the smooth rods of the X axis. To provent this, you can use this mod that raises the Y axis by 12mm. This way the Y belt will be…
Remix of the below, originating from TheJeffChen https://www.thingiverse.com/thing:4666227 https://www.thingiverse.com/thing:4771721 -Increased some of the tolerances and removed sharp edges for easy of fitment -Added a Scart bracket that…
///// I highly recommend printing&building Thing: 6387573 (updated version by "markeno") ///// I've designed another case for the GBS control unit. You will need 2x M4 x 10 mm screw with nut (for SCART connector) 2x M3 x 10 mm screw (for…
I lost one of the pads for my old 2" quick grips. I modeled this pretty quickly so it's not perfect. It could use a few tweaks for a better fit, but it works well enough as-is. Print with TPU! (or other flexible filament) I printed at…
A common Housing for a Velleman K8200/3Drag Controller and a Raspberry Pi with Camera (especially for octoprint) Take the webcam housing and the cover from here: Raspberry Pi Camera Housing Attach controller and Pi with short 3 mm pan…
The end stops for X and Y axis are difficult to adjust as they tend to get loose when unscrewed. The original two screw construction is complicated and I made this simpler "one screw" replacement for the axis. There is no need for precise…
This is just a remix from Danyboy's design, but the cable is on the opposite side. Print one "Alim_droite" and one "Alim_gauche" parts. Print Settings Printer: K8200 Rafts: No Supports: No Resolution: 0.2mm Infill: 10 Category: 3D Printer…
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000427 : Planetary flange
My attempt for an eclosure Instructions Part list 2 square meter polystyrene ? 3 mm bolts 12 mm long ? 3 mm bolts 16 mm long ? 3 mm spacers ? 3 mm nuts ? Chassis fasteners 2 bottom corners 2 bottom corners 2 front connectors 3 front…
Didn't have the right bearing but did have pom wheels for the Ender 3 Pro so I made new 'wheel covers' to fit those (24mm internal diameter). Also didn't use the supplied spacers and just used washers.
Correct bed leveling is essential for good prints - Marlin firmware now has this awesome feature of measuring the bed and automatically adjusting the Z axis when printing. As this YouTube video demonstrates. I had a small used 8mm…
Tait TM8200 10 inch rack ear
Based on http://www.thingiverse.com/thing:369891 , this mount has a 90 degree angle, so that it fits on the right upright on the K8200. Category: 3D Printer Parts
Original made by Rob Mitshi was for E3Dv5 Category: 3D Printer Accessories
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000426 : Planetary holder
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. 66 teeth ring for epicyclic gear train. Part of the extruder reducer.
These thingies I made in order not let the printbad make contact to my enclosure. Instructions I used three each to get enough space. Category: 3D Printer Parts
When watching a movie with the lights off I realized the modem leds were way too bright. I decided I wanted a cover I could clip onto the modem to reduce the leds intensity a significant amount. I achieved that goal lol Printed with .2…
This is a further refinement of my cable driven Z axis for the K8200 or 3Drag. It uses a cable loop to ensure the Z axis is driven from both ends, and at the same time provides a large degree of "z wobble" isolation, though a severely…
Yet Another X-axis holer for the Velleman K8200/3Drag printer. I have been looking for a stable holder with the end stop mounted on it, as i dont Think that there is a Point in moving the screw. This is designed so that you can cut of the…
Precise calibration of the zero point Instructions Layer 0,2mm infill 15% perimeter x3 Link to micrometer: http://www.ebay.com/itm/331109043919?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Category: 3D Printing
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000432 : E motor mount Replaced by : https://www.printables.com/fr/model/599730-k8200-upgrade-2-e-motor-mount-v2
ClipOn Fan mount for standard 5015s (50x15mm) centrifugal fan used in many 3D printers today (as Prusa i3 MK2). Mount is the blue part on the picture. The cooler fan that comes with the K8200 kit is far from optimal - with unfocused part…
Small support to put a logitech webcam on the side of the Z axis. You'll need 1 M4x10mm and a nut to mount it. Print Settings Printer Brand: Velleman Printer: K8200 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 10%…
Mounts the Bulldog XL Extruder rock solidly to the Z-bar of the K8200. Inspired by this . I wanted a simple solution that's ridiculously rigid, and at the same time doesn't force you to disassemble the printer; and this is it.…
Completely redesigned in OpenSCAD to lower the base of the hotend and make it easier to fit a slot mount hotend in place of the original Updated to easily switch between 3 and 1.75mm paths, and to replace steep overhangs with small…
Tensor para correa del eje X de la impresora Velleman K8200 ·Configuración de impresión FDM Impreso con calidad 0.2 de resolución y relleno (0.4) cada 2 capas para ahorrar tiempo de impresión. La tasa de llenado debe ser al menos del…
This is a mount for a 18mm inductive probe. It will mount the probe behind the extruder using 1x M5 screw and nut, so you will have enough clearance to add whatever you want. Print Settings Printer: K8200 Rafts: No Supports: Yes…
If you have mounted the E3D V6 on the extruder, the original adpater is too high, this one is 2 mm lower and will allow it to be mounted. It might need a Little CA glue ;-) Category: 3D Printer Extruders
RD8200SG Comes with the flimsiest and uninspired phone mount for having your phone attached with your locator. I designed this from scratch and it's my first version. Printed with PLA Gyroid 60% infill and it's very sturdy. The ball joint…
The is a mount for a genuine E3D v6 all metal hotend and E3D Titan extruder for the Velleman K8200 / 3DRAG 3D printer. Only one part is required to mount the hotend and extruder, but I also made a modified mount for the fan duct produced…
What is this? A rig to mount a small 9G RC servo, with an arm mounted Z-endstop, next to the extruder on a K8200/3Drag to enable the Auto bed leveling feature in recent Marlin . I had to modify the probe holder by zenmaster a bit to…
Model includes only bare beds/inserts, it's up to you to cut placements for you tools. See attached pics for examples, this model is accurate enough to allow precise tools placements.
Made my own mounting plate for my QR extruder. Combine with the top part from the standart mount from Bondtech homepage: https://www.bondtech.se/sv/kundtjanst/utskrivbara-stl-filer/ Works great. Category: 3D Printer Parts
K8200 aluminum profile to mount of the HeroMe Gen7. The mount should allow all the interchangeable hotends and cooling solutions for the HeroMe solution. Do as you will with it. This assists in reviving an old dinosaur bedslinger with…
Designed to be used with the original Hotend mount and with a maximum 22mm Hotend Parts needed -4 M3 Screws -1 25mm fan Simply disassemble your Hotend support, then put your new fan mount and put again your Hotend and your Hotend mount.…
Assumed at first this round button was a dial, it was definitely not and our cats love to come in and turn the heater on and off as they please. They seem to have not figured out how to remove it so far so I'm happy for now.
I modified http://www.thingiverse.com/thing:395908 added lightening holes and slot for mounting with clamp Instructions Frame is for mounting left and right, fix with clamps 180x4.5 mm. To mount without any problems at the bar, slightly…
Il suffit simplement de dévisser les deux espaceurs qui maintiennent la Hotend d'origine en place, de venir glisser la nouvelle Hotend dans la pièce, de mettre la pièce et la hotend dans leur emplacement, puis de venir visser les deux…
This is a replacement rubber return-bumper for the Sigma SM8200i typewriter. It’s the small rubber piece that cushions the hammer/print striker after it hits the typewheel to print a character. On my two machines, the original rubber has…
A simple and efficient mounting bracket for a Traco TPP-150 series Power Supply Print Settings Printer: K8200 Rafts: No Supports: No Resolution: 0.2mm Infill: 10 Instructions You'll need to print two times the bracket, two M5 by 8mm Bolts…
Clip fermacavi per stampante 3d K8200 / 3DRag da: 5 mm 10 mm 15 mm Category: 3D Printer Accessories
The rubber feet on vintage Sigma SM8200i typewriters often deteriorate or crumble with age—mine certainly did. To keep the machine stable and usable, I created a 1:1 replica of the original feet as a drop-in replacement. These replacement…
![ICON 10 in. Pliers Wrench [58200] (Gridfinity)](https://media.printables.com/media/prints/cf66cf2e-2b6c-4c20-a405-9dc2a0d2615a/images/10717290_f86dd5e2-a981-4040-bb1c-6a079b4e1ed8_2d4bf60d-c192-4704-b42a-5466183dd82f/icon_10in_pliers_wrench_58200_screenshot.png){kind=icon}
