Liczymy pasujące modele…
This bracket is made for 10" racks. They have the standard dimensions of 1U (44.5mm) in height and 250mm in width. With these dimensions the mount can be printed on a print bed with the dimensions of 220mm x 220mm. The mount is designed…
A 10-inch rack mount for the TP-Link TL-SG108 | TL-SG108PE | TL-SF1006P | TL-SG608E switches. This mount has been tested on both V3 and V5 hardware revision of those switches, but it should be compatible with other revisions as well. I've…
Just a addon for the Lego Skeleton: https://www.prusaprinters.org/prints/78695-mega-lego-like-skeleton-101-scale I wanted the Lego Bicorne for my skeleton. Did not have the skills to make it myself. So after a long time trying to make it,…
The original clip of the armrest of Audi A3 8p (2002-2010) is very fragile. I had a similar issue with my previous Audi. :-( This model can be used in replacement of the original clip. Let me know if it works for other Audi models.…
29T pinion compatible with the Kyosho Fazer FZ02 RC touring car. Provides additional torque/acceleration over stock 32T pinion, at the expense of some top speed. Pitch is 48DP (48 teeth per inch of diameter) and should be compatible with…
NEW MOUNT HERE: https://www.printables.com/model/877941-manta-m8p-din-mount-v2-low-profile They are used to mount the BTT Manta M8P Board to a DIN rail on a low-profile mount.
My design of powerbank based on chinese pcb and 1s8p pack from my previous powerbank. Main body is designed to be printed standing with display hole on top. To fix parts together you need 4-6 m3 screws with cone head.
A remix of @Anollya_1115736 M8P Fan duct but with @SimplifiedLife's Vents from his Octopus Duct, I increased the walls to be thicker on top and sides for it to be more sturdy (the original cracked for me, and a optional bracket to use if…
Simple brackets, takes 4 screws. Mounts the switch upside down and leaves some air through for cooling. Updated with V2 for a nicer printing result, without the elephant's foot through the rounded bracket. It's angled now.
Un chargeur portable puissant et pratique, parfait pour les urgences ou les déplacements. Nous avons utilisé une batterie 18650, choisie pour sa capacité élevée (jusqu'à 3000 mAh) et sa disponibilité. Ce chargeur peut alimenter…
Remix or Yanev's model. I've removed the MicroUSB hole, fixed the screw holes and most importantly, I've removed the big slot to see the charge percent and replaced it with small 1.5mm holes to add a transparent acrylic rod for the LEDs.…
This has built in supports. Print as oriented and no supports. Lid is designed to use 120mm Fan.
This is very simple phone mount for the Audi A3 8P. No need to pull out the air vents, you can simply slide the mount in between. Additional you will need any sort of phone mount with an ball mount.
This is a Manta M8P Mount for my DIN Rail Bracket. You can find the bracket here ! In addition I created a fan mount. The fan mount can be used without the rail mount. The fan mount is for 40mm fans. The printable spacer can be edited to…
For cooling the TMCs on the Manta M8P. I tested it with BTT TMC2209 and sunon 5015. Print it upside down. Screw: M3x8 SHCS Category: 3D Printer Parts
They are used to mount the BTT Manta M8P Board to a DIN rail on a low-profile mount. Print settings: I used ABS @ 0.2 Layer Height Used normal supports (Tree supports caused weird issues) Filament: Ice White ABS @ 240c, 100c Bed
This model was created by modifying the Octopus DIN mount from @clee
Designed this model to hold and support the BigTreeTech Manta M8P board uses the 4040 extrusion and T-nuts to secure it to the sides and back but will utilize the existing holes for cable management. It will be slightly tight to install…
I needed to make something to attach to a PET bottle and couldn't find a model file to import into FreeCAD. So here's one. The model is not really useful for anything (unless you desperately wish to have a ring screwed on top of your PET…
Cooling Hood BigtreeTech Manta M8P v1.1 and v2.0 For CB1/CM4 with 60x60x15 Fan M8P. drivers with 5015 Blowerfan. And ziptie mountingpoints for esay wire wireing.
BTT manta m8p v2.0 low height dinrail mount print 4 rings, dinrailmount1 and dinrail mount2 4pcs of M3 screw (length 8-12mm) will be needed.
just removed the front logo because I could not get it to print cleanly.
Fits well with Voron design DIN clips. https://github.com/VoronDesign/Voron-2/blob/Voron2.4/STLs/Electronics_Bay/pcb_din_clip_x3.stl
TP-Link Omada ER605 and SG2008P 1U Rack Mount
This rackmount adapter is designed to mount the TP-Link TL-SG1008P switch in a 10-inch network cabinet. The frame takes up 1 unit of rack space (1U) and is optimized for ventilation to ensure efficient heat dissipation. The adapter can be…
04/10/2024 add mount v1.1 for m8p 1.0 1.1 2.0 https://www.printables.com/model/838734-btt-m8p-v20-cooling-dockfan-mount-v11 BTT m8p v2.0 cooling dock for cb1 mcu and step driver also work with m8p v1.0/v1.1 add DIN rail mount for install…
I will upload an actual photo as soon as the print is finished
UPDATE !!! Version v2 : Added 2 sizes of balls for mounting The shape of the installation has been slightly changed (optimized for ventilation grilles)…
Based on the very good model of ER605 & OC200 Rack Adapters (V2) by Sorcier, I remodelled them to fit 2x TL-SG2210P. It's a heavy device, and 2 of them in this pair of brackets are recommended to be supported, either by support angles or…
The Zaribo ZLC kit comes with a BTT Octopus Pro, but I wanted to run Klipper and have things as tidy as possible. A BTT Manta M8P does the job but is slightly larger and has different mounting holes. I remixed the Zaribo case to suit the…
I created this board holder for the Big Tree Tech Manta M8P board. It also allows you to mount fans above the board for cooling included dual 4020 fan mounting option( Untested! ) as well as standard PC fan mounting option. I have…
** modified DIN rail version coming soon, it's in the early testing stages to verify fit and design update (UNTESTED) but currently printing** Designed to hold a Manta M8P Mother board with or without the CP1 addon Printed in ABS test…
This is my design of a dart holder for Nerf toy guns. I design one to stick to your gun and one with a buckle to put it on your belt. Just print it standing up and it will print perfectly.
IP5328P module case This is a remix of 3D printed case for very popular IP5328P power bank module. This module supports 18W of charge/discharge and is capable of delivering 12V at the output. I made a remix to be compatible with the M3…
Rack mount for TP-link ER605 router and/or TL-SG108PE switch Files are only provided in one direction, don't forget to mirror to make the complete 1U unit Holes are 3,5mm. Use M3 screws and nuts. I had to redrill. I printed mine in very…
rotated the honeycomb pattern to make it easier to print
I needed a mount for my Manta M8P for my Switchwire (Ender conversion). Due to size constraints, I originally designed the 4020 mount, then switched to 2020. There's one quirk which I'm unsure of: The camera/display ports sit under the…
10" Rack Mount Solution (1U) for a TP-Link TL-SG108PE Switch. You can use double-sided tape to secure the power brick in place and zip ties to manage the power cord. The screw holes are designed for M5 screws Dimensions ( in mm ): W=254 x…
Ich habe hier einen Kennzeichenhalter für einen RS3 8P erstellt bzw. so geremixt, dass er für den RS3 8p Grill funktioniert. Da ich keine Schriftzüge mag und sie meist unschön beim drucken werden, habe ich diese ebenfalls entfernt. Ich…
Description Running drivers at higher currents causes them to become extremely hot. To ensure reliable operation, cooling is necessary. This fan case provides ample cooling for all 8 driver slots and has been tested with BTT TMC2209,…
esp-32 wroom (38pin) case, with click backside. size inside case 55.34mm x 28.1mm size outside case 60.4mm x 31.2mm print description: Filament : PLA Color Changing Brown/Green Nozzle : 0.4 Layer : 0.2 Infill : 20% If you like it. let me…
Hier ein Gehäuse für das BigTreeTech Manta M8P für den Cáribou. Es sind jeweils ein Lüfter für die Motortreiber und ein Lüfter für das CM4 Modul vorhanden. Gedruckt habe ich es in PETG und 0,2 Schichthöhe.
Printed it with ASA, Nozzle 0.4mm, Layer Height 0.2mm Can used together with the fan mount → https://www.printables.com/model/1100119-flat-btt-manta-m8p-120mm-dinrail-mount Changelog V2 increased screw tube stability and size a bit Love…
Wings to be able to mount a Cisco C1000 into a standard 19" rack. I would recommend printing in PC or another tougher material since the wings have to deal with a decent load. I printed these with 5 perimeters with 20% adaptive cubic…
Replacement vaporizer head for NE-C28P, 3D design thanks to Mervin
THIS VERSION USES HEATSERTS. The Zaribo ZLC kit comes with a BTT Octopus Pro, but I wanted to run Klipper and have things as tidy as possible. A BTT Manta M8P does the job but is slightly larger and has different mounting holes. I remixed…
A spring based flat mount for BigTreeTech Manta M8P boards on a Voron printer (or similar with DIN35 rails). Can used together with the fan mount → https://www.printables.com/model/1076080-btt-manta-m8p-120mm-fan-mount You also need 4x…
Gridfinity 3x2x3 holder for Harbor Freight 8pc. Pin Punch Set https://www.harborfreight.com/8-piece-punch-set-93424.html Also seems to fit Starrett 565 punches but not tested all sizes.
Print Settings First Layer Height: 0.25mm Layer Height: 0.2mm Extrusion Width: 0.4mm, forced Infill Percentage: 40% Infill Type: Adative Cubic, Grid, Gyroid, Honeycomb, Triangle, Cubic Wall Count: 4 Solid Top/Bottom Layers: 4 Seam…
37T pinion compatible with the Kyosho Fazer FZ02 RC touring car. Provides additional top speed over stock 32T pinion, at the expense of acceleration. Pitch is 48DP (48 teeth per inch of diameter) and should be compatible with other 48DP…
BOM: 4 of threaded inserts (Voron standard M3x5x4). 4 of 30mm SHCS to attach the mount and the Manta board. 4 of whatever length M3 screws you need to mount your fan. I used 25mm SHCS. Print instructions: Set “Bridge counterbore holes” to…
I am a big fan of heat set inserts so I adjusted the original to allow for some heat-set inserts instead of screwing directly into the filament. I only used the Heat-set inserts to hold the lid, not to hold the board in place as I expect…
This low profile DIN mount for the Manta M8P v2 shifts the board off center on the rail. There are two different versions available, both moving the center of the board by 10mm but in different clamping directions. Mounting holes are…
This is a two-piece enclosure designed to securely house an ESP32 Dev Board and mount it to a wall. The enclosure fully encloses the ESP32 while allowing access to the USB Port. No support material is required for printing. The design…
Ignoring the wires, this print will help you mount the BTT Manta M8P to a din rail. I've included the step and f3d files, so you can customize it quite easily to attach to just about anything. This build uses 4025 fans to cool the…
After the print, I drilled out the holes in the mount to 4mm to fit heat set inserts. I also drilled out the holes on the fan mount (on the legs) to 3.5mm. This is an optional step I chose to take.
This kit allows you to install the BTT Manta M8P motherboard into the SV08 3D printer using a precision-designed mounting bracket and cooling shield system. The red IO template helps mark and cut the existing "milk tray" (see attached…
I needed a board mount for the Manta M8P. Thank you @Byte Insight for the Step Files
Bit organizer and holder for 48pc long type screwdriver bit. You can hold the bits on your desk/workspace in clear and visible position. I print with Fuzzy skin from ABS and/or PLAG material 20-25% infill for durable construction.
This model is compatible with the lego system.
Insert holds: M12BLIDRC M12 battery (in my case M12HB2.5) M12TC2 USB charger Small compartment in the back for bit holder or other small parts Remaining space of the organizer is used to store a SHOCKWAVE Set 38pcs (4932492009) or other…
This is a holster style mount for the Ryobi R18PI Compressor, it allows you to mount it to the wall whilst still being able to immediately grab the driver with no obstructions. I store the batteries seperate, however it will take the…
This case may not be compatible with ender3s with shorter pads. My ender3 measures 45 mm from the underside of the Y-carriage extrusion to the table, while this case measures 42 mm. Additional Hardware 4 M3x16 (Cover) 4 M3x6 or M2.5x6 for…
This is a cable comb for braided PC cables. I wanted one for my graphics card and couldn't find one that was wide enough. My first design is included as well, but it is to tight for sleeved cables. Though it is perfect for regular ones ;)…
Modeled and printed this back in the summer of 2022. Sadly, the battery have already degraded significantly when I finished modeling & printing this but I still see value in this model I made. Remix it on Onshape:…
I used 15% infill and supports for the clips, print them with the flat side down and it will be perfect. They dont come in contact with the turnsignal or the wishwater lever.
original stl file converted to STEP
This BTT Manta M8P mount is designed to install the MCU board across two DIN rails. This rotates Manta by 90° and helps a better air flow when installed in Voron 2.4/Trident printers. BOM: 4 x Voron RS25 PSU brackets from…
Tool holder for Socket Wrench Set 28pcs. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 115,65mm W - 35mm H - 70mm We…
The plate is available as Plain, with HevORT logo, with Voron logo, with VzBot logo and with Zero G logo. Zero G Logo shown in pictures. You can either print it the stl, makes it 3mm thick or use the dxf file to order a part cut in a…
This is a replacement drive gear for the Hayward The PoolCleaner 2 Wheel Suction Cleaner. This may also fit the 4 wheel version also. Item #W3PVS20JST Gear, Drive, Small (2 pk) - PVXH008PK2 PART # PVXH008PK2 ALTERNATE PART #'S 87-150-1830…
Simple eggs holder for the fridge :) printed with PETG
Modified fan mount for using M3 brass inserts
I remixed from this model from: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/rsheng118/BTT_octopus_DIN_vertical_mount I just changed the screw positions to match the manta holes. Print Settings - Voron PIF: Layer…
Please check your slicer's Slice gap closing radius!!! PlanetaryBearing_OD64_ID22_H10_S25P11x8R47_b30_e0.1 OD: 64mm ID: 22 Height: 10mm I recommend to print with regular PLA Silk PLA is a very difficult material choice for this part. Some…
Find out everything you need to know about the connector on my blog: https://nerd-corner.com/3d-printed-dupont-connector-for-jumper-cable/
I needed a new phone phone mounting solution in my trusty A3 Sportback. I had been using a Celly vent-mounted magnetic holder, but this ultimately caused damage to the vanes of the air vent, so I designed this ‘plug-and-stem' holder to…
BTT Manta M8P V1.0 – Simplified CAD Model This is a one-piece CAD model of the BTT Manta M8P V1.0 MCU . Unlike the official model released by BTT (which includes all components and fine details), this version is a lightweight, simplified…
Snug fit. Better use PETG, because bearing may become hot, when alot of breaking.
⌀4,22 mm holes for ⌀5mm M3 inserts. For completion i used M3x10 bolts and drilled rubber stoppers from rails as spacers.
This is a MCU Board mounting bracket for Octopus and Manta M8P that holds 4 BTT TMC5160T Pro drivers for AWD Mods/VZbot. BOM: 20X M3*4*5 Heat set inserts 20X M3*8 SHCS (If using the fan cases in the picture then 16X M3*10 and 4X M3*8) Two…
The IP5328P can be installed facing up or upside down (see "ud" in the filename), which makes it slightly smaller. The version with the IP5328P facing upwards is easier to install overall, but please note the picture showing the cable…
Boom: 3 - 5010 Fan 1 - 4010 Fan 3 - M3x8 SHCS ( Mount Bracket to M8P) 15 - M3x16 SHCS or ISO 7380 (Fan) 15 - M3x4 OD 5 Heat Inserts (Fan) 3- M2.5x10mm SCHS (CB2) Note: updated model to correct some errors on the fixing holes
Heavily inspired by this design: https://www.printables.com/model/494301-gridfinity-wiha-7pc-precision-screwdriver-tray-for Matches my other design as well:…
m8p Pavan M8P Pavan - BTT Manta M8P Fan Mount for Cooling Stepper Drivers Features Designed to fit and cool the Manta M8P stepper motor drivers and CB/CM4 module. Fans: Two 5010 fans for the stepper motor drivers and one 4010 fan for the…
Tool holder for 18 pcs Screwdriver Set.. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 130mm W - 70mm H - 80mm We design…
hpi spur gear for sport 3 chassis
Needed a mounting system for my iPhone in my car. Works awesome, have to upgrade the single hole so it wont rorate anymore. Feel fre to contact me. Used m3 ruthex Brass threaded bushings
This is a 3D printable glue-fit enclosure for building a custom power bank using the IP5328P_V1.0 module and a 1260110 high-capacity 3.7V 10000mAh Li-Po battery . The design ensures a precise internal fit while offering a compact, sleek,…
This is 19" 1U rack mount bracket for a Netgear 8-port Network Switch (GS308PP). It's pretty beefy because it will be in a portable case and need to stand up to a lot of rough handling. I printed this with PLA on a Bambu Labs A1 Mini, so…
This is a fan mounting board for the BTT Manta M8P motherboard. It holds 2 - 60mm and 1 - 40mm fans.
I Needed a 5mm pinion gear while I waited for mine to ship. It's very tight around the shaft, you might want to drill it out a bit larger or remix. I haven't run it yet as I only printed a test part to fit. I would suggest abs probably.…
Easy to print and no support needed ! This is specifically for the RYOBI Impact Driver (R18ID2) and drill (R18PDBL). I printed an old version(see pictures) and I'll upload the new pictures of the models I shared when I have the time to…
8port - PC4-M10 for palette 3 pro 8port - PC4-M6 for palette 3 pro
This 18650 case is designed to fit a 3S8P battery with the balance board. There are 2 different designs: The Spacer files are for people that are using the 18650 spacers to make their pack The No Spacer files are for those who are not…
Just a quick sketch to hold my nerf ultra darts little bit cleaner around the house. F3D file included for remixses
This Manta M8P V2 mount should fit the V1 with minor clearancing. I added more material around the mounting locations for M3 heat inserts. I also changed the 2020 mounting to M3 size but that can easily be edited back to the original size…
Držák flash disků 28 kusů včetně náběhů
Decided to try my hand at designing my own model. Was needing a case for both of these components, I am slowly working my way to building the Mercury one.1. Only designs I could find required me to cut my stock enclosure, which I did not…
![Manta M8P Din Mount [Low-Profile]](https://media.printables.com/media/prints/668101/images/5256674_5521af56-becd-41f5-813a-5b84d56328b4_36a0ac49-7227-4156-9a80-b022f46e3eb0/screenshot-2023-12-03-000320.png)
![Manta M8P Din Mount V2 [Low-Profile]](https://media.printables.com/media/prints/877941/images/6733070_db2cef09-e492-48f2-969f-1a04aab64951_e62331b1-5842-4085-806a-3a9de3476de1/20240512_222812.jpg)
![BTT Manta M8P Cooling D3D Design Logo For Creality K1/K1Max [UPDATED]](https://media.printables.com/media/prints/983757/images/7498502_8aba1a39-bb31-4bfa-adf8-86c68ffc02d5_215e0775-ab44-4494-8388-81947f8b62d9/btt-manta-m8p-fan-mount-v16.png)
