Liczymy pasujące modele…
Supernote A6X2 Nomad case with Samsung S7 pen magnets to hold device (20 x 1.7 x 6 mm) magnets to hold pen (5 x 1 mm) magnets to hold lid (6 x 1 mm in bottom case + 9.5 x 0.7 mm in lid) felt as cover material (2.5mm) working as hinge I…
Wydruk około 2,67 €–3,26 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Case for the PINE A64 SBC.
Wydruk około 2,53 €–3,10 € nettoWstępna wycena jednego wariantu
I have made some Profiles for myself to Print these Nylons and wanted to share these for others to use. These are for the P1S but they probably work for the X1C aswell, i am using Orca Slicer and the 0.4mm Nozzle.
Gas Cap Tether for 2012 Audi A6. Should work with other car models too. Part Number on the gas cap is 3C0 20 553L. You must print in TPU or another flexible filament! PLA or ABS are too rigid for this purpose and will snap. Print Settings…
See Text file for settings, orcaslicer profile in the .zip. To add go to file-Import-Import Configs and it should add it in. It will only show under bambu p1s 0.4mm nozzle size To avoid confusion. the filament will be added under the…
Headlight washer covers for Audi A6 C5 allroad. Re-modeled based on original 4Z7955275 part. The thickness of hooks (the ones that latch on the washer nozzle) is slightly increased for durability. The scale is OK. See comparison photos.…
A diffuser to smooth your Sony a6000 pop-up flash! Measured to fit your Sony camera flash, * might* fit in similar models Conscientious Topology design Precisely measured with sufficient clearance for a snug fit Alternative version of the…
A diffuser to smooth your Sony a6000 pop-up flash! Measured to fit your Sony camera flash, * might* fit in similar models Conscientious Topology design Precisely measured with sufficient clearance for a snug fit. Alternative version of…
I created this model to safely store my aviation documents in the pilot bag.
This cap hooks to supernote pen holder, and fits the Staedtler Noris Digital EMR pen. Print with support, as in the picture or .3mf file.
Gehäuse für ein Pine64. Das Gehäuse kommt komplett ohne Schrauben aus, und wird einfach zusammengesteckt. Der Deckel wird per Klip gehalten und kann durch leichtes anheben der Klammen an den Rastnasen wieder geöffnet werden. Am Boden…
Backplate for A6X2 using magnets to attach to the device. OBJ and Fusion files included to adapt for your use case. Dimension are accurate to tablet. I found a iPad mini cover from clearance that almost fits A6X2 neatly but is just a tiny…
Folgende Dateien stehen für FM268M-DG3+ zur Verfügung: V1_ATX_Slotblende_FM2_ASRock : Die Blende muss nachgearbeitet werden. Der Einbaurahmen ist etwas zu groß. Den hervorstehenden Rahmen mit dem Cutter abkratzen hilft.…
This is some small improvements for the y-belt tensioner of the Anet A6 Evolution cube type printer https://www.thingiverse.com/thing:2067818 : Guidance to avoid torsion of the belt Enlarged body for using 15mm washers (DIN 9021) The…
This case for the Pine64 does not need screws, it easily snaps together after printing. Printing The attached .3mf file has the parts ordered so everything prints in one operation. With my 0.8mm nozzle it took a bit over 3h to print.…
This is a custom designed clamp-on handle for Dewalt right angle adapter DWARA120 and DWARA60. This right angle adapter can be difficult to hold and maintain the drill or driver alignment due to the torque applied by the drill or impact…
This is a simple protective case for the Supernote Nomad A6 X2. I did not want a bulky folio with a front cover as that just makes the whole thing a bit cumbersome to use around the house. This case provides basic protection from everyday…
Snap on Panoramic "Viewfinder" adapter for the Sony a6000. Use with a 16mm lens to get the FOV of the Hasselblad X-Pan. Crop the image to 65:24 or 1:2.7 in Lightroom or your program of choosing. Example images taken with the Panoramic…
A PINE A64 Case - an alternative for raspberry.
I don't like existing notebooks at all: you need blank sheets of paper to sketch, and most notebooks are either lined or squared. They also lack a bookmark—you have to insert all sorts of papers, which is inconvenient. I want the sheets…
This is a replacement drum paddle (also known as a drum lifter) designed specifically for the Sharp ES-HFA6103WD washing machine . It replaces the original part located inside the drum, responsible for lifting and agitating clothes during…
Usage The plate has for purpose to hold in place cables on the FRA600 from Askar. It uses the finder's screw holes to stay in place. Since the FRA600 has only one finder spot, and plate is retained on one side only, but it doesn't affect…
After buying an Ultimea A60 7.1 (more like 5.1.2 but who cares) Dolby Atmos surround sound kit, i wanted to use the manufacturer provided wall mounts but all mounts will place the speakers at a 90° angle compared to the wall,a nd the…
I understand that the Zero had a 3-bladed propeller, but for the wall art lines I prefer the look of a spinning prop
I replaced the halogen lamps with LED lamps. Since the LEDs require more space than the halogen lamps, and the original cover glass no longer fit (and was also broken), I designed an alternative cover. Note: Due to their low power…
The Audi A6 wheel hub cover is a sleek, modern component designed to fit the center of an Audi A6 wheel. The design comb
A quick redesign of the spike tool for hutikka69 . Included step files in case it needs to be longer. Printed at 0.24mm layer height, 4 walls and 40% infill with a 0.6mm nozzle. Sturdy enough that I Can't really snap it by hand, only…
Cable guide with possibility to easily remove cable. Print Settings Printer Brand: Anet Printer: A6 **Rafts:** No Supports: No **Resolution:** 0.2/0.12 adaptive Infill: 30% **Filament:** Gembird ABS blue Category: 3D Printer Parts
Sony in all it's infinite wisdom made it so you can't clip a Rode (or other) recording device to the hot shoe unless you remove the eyepiece cover. Really a genius move. This means that not only can you now lose your hot shoe cover… you…
I don't like existing notebooks at all: you need blank sheets of paper to sketch, and most notebooks are either lined or squared. They also lack a bookmark—you have to insert all sorts of papers, which is inconvenient. I want the sheets…
This simple holder will let you mount Airtag to Sony A6700 camera when using dedicated Smallrig baseplate. To mount it you need to open the lever on your baseplate and slid two tabs into dedicated spaces starting with the "inside" tab…
Diese 3D-druckbare BINGO-Schablone im DIN-A6-Format richtet sich an Nutzer, die BINGO-Lose online kaufen und dennoch eine haptische Möglichkeit zum Ankreuzen der Zahlen auf Papier nutzen möchten. Die Schablone ist für handelsübliche…
I replaced the halogen lamps with LED lamps. Since the LEDs require more space than the halogen lamps, and the original cover glass no longer fit (and was also broken), I designed an alternative cover. Note: Due to their low power…
After buying an Ultimea A60 7.1 (more like 5.1.2 but who cares) Dolby Atmos surround sound kit, i wanted to use the manufacturer provided wall mounts but all mounts will place the speakers at a 90° angle compared to the wall,a nd the…
Audi A6 allroad level detection rod support for 2013 year air suspension. Don't know if this works on other models also. With this fixed broken rod without need of change of component.
This is a high-performance, integrated Garmin mount specifically designed for the Syncros ST-R100-AL stem. It mounts directly under the stem faceplate for a clean, aerodynamic "pro-cockpit" look. The geometry is specifically optimized for…
There are one or two 3D printable shelves on the internet designed to hold a Sony A6100 Camera but none are designed to accept the camera without first removing the Peak Design Capture plate. The shelf holds the camera ~18mm Away from the…
This little piece slides into the flash socket on the Sony A6000 or A6500 cameras to hold the flash so it points up as shown in the photo. This allows the flash to bounce off the ceiling instead of hitting the subject directly. A bounced…
Fan mount to mount 2 A6x15s or presumably any 60mm x 15mm fan. mounts to the 2 holes on corner support bracket using one of the Velka 7 screws and an m3 nut. if a fan grill is needed, set the 2 parts over the fan to an infill pattern with…
I have an Gorenje WA60085 washing machine, and spring that holds main drum broke which service guy replaced, but there was no original spring holder (it flew into the void :-) ). Washing machine worked but spring was squeaking during…
ive got a Banner branded hole punch which the original paper guide broke and was no longer usable, so i designed a simple paper guide to replace the broken one for paper sizes A3 all the way up to A6, i designed it based off the Banner…
In my case I used PET-G on a Elegoo Centaury Carbon, with 3 walls and 15% infill.
Bins I designed to hold my A6 photo prints! Also has a version with dividers I made for packaging of various sizes. The ones I printed are a bit shorter than the original model, as my filament ran out just before the end of the print and…
Custom-designed and 3D printed compound gear set made for precision motion transfer and compact mechanical assemblies. This design features a large spur gear integrated with a smaller pinion gear, allowing for efficient speed reduction…
Clips to hold foam-board insulation to the bottom of the Anet A6 heated bed. IMPORTANT: If you do this project, you will be putting potentially flammable and electrically conductive material near/on the electrically-powered heated print…
The original fan spacer works great. I wanted some light down by the print nozzle, so I could watch the print without using a flashlight. I modified the spacer to add an area for LEDs. I stuck a small strip of LEDs on and wired them into…
I snapped off the corner of the front plate of my Anet A6. Fortunately, it still held the rod well enough that I could print, so I designed this replacement. As close as I could measure it, this is dimensionally accurate for the front…
02-11-2018 Anet changed the default A6 power supply around the beginning of 2018. The STL has been modified to accommodate the change, and still work for pre-2018 printers. (i.e. some internal features were removed, and the screw hole…
Maybe my Anet A6 is slightly different dimensionally than other peoples, but none of the belt tensioners I tried worked quite right. There were some clever designs, but things were not quite in proper alignment. So, I reworked and…
The original belt tensioner by vernierroger is a very clever idea/design. However, I had some trouble fitting the internal components into my A6 X carriage. Also, I was confused as to what hardware (nuts and bolts) I was supposed to use…
the original part was broken in a way that it could not hold the compartment door closed properly anymore, so i modeled a similar part to replace the OEM part, this one does the job well and was a quick print.
Frontmatter The first entry to my Zettelkasten series, I guess. I'm an academic in the humanities and my preferred medium for processing literature is pen and paper, which has led me to my variant of Luhmann's Zettelkasten system. My…
Plastic cover for the protection of a KA600 SINNO Digital Ruler.
The genuine versions are very rare & usually very expensive, unless the seller doesn't know what they have & that is even more rare. I had some light weight tube to hand ( 25.5mm OD & 24mm ID ) so I made my own version. This doesn't lock…
This is a simple box that slides apart. I printed it on a prusa mini with a 0.6mm nozzle. It fits A6 notebooks, card or photos.
This organizer is specifically designed to hold A6-sized memo pads, but it can also be useful for any similarly sized notepads. The design features sloped edges for easy access to the notes, and it has enough space to store a pen and a…
Bring ultimate monitoring to your computer with the AIDA64 SensorPanel 7" HDMI. This high-quality 7-inch IPS display with a resolution of 1024x600 pixels and HDMI input allows you to monitor all critical system information in real-time.…
A 3D-printed IKEA Skadis mount for the Mobula 6 FPV drone would be a compact and functional holder designed to securely store and display the small quadcopter on the popular Skadis pegboard. The mount should feature a custom-fit cradle or…
This 15cm x 10cm (6 in x 4 in) photo frame features a built-in stand, no need for additional support. For vertical pictures.
This 15cm x 10cm (6 in x 4 in) photo frame features a built-in stand, no need for additional support. For horizontal pictures.
Gridfinity Dimensions: 3x4x6U Remix The model was made with OnShape and should be available to all https://cad.onshape.com/documents/d2b1533fdd4339235a0aeaef/w/dfd6302d8036a7602175fc06/e/f49bf226e032e3ca43eda72d For some reason the viewer…
Trimui Model S / Powkiddy A66 cap to enhance your d-pad experience ! If you are used to Gameboy and other similar "rolling" d-pad device, you may have notice false inputs using this device as the d-pad lay on a all-flexible support and…
Backplate for Trimui Model S / Powkiddy A66 with extended space for a 523450 Li-Po battery. WARNING : Opening, modifying your handheld may void your warranty. I will take no responsability if you break something. To do this mod you will…
It's my own remix of the stand P51-D Mustang RC plane stand by 3dlabprint. I printed it with Polymaker PLA+ Black; 3 walls; 20% infill cubic; I recommend printing with a minimum of 4 brim to avoid lifting the piece from the bed!
I lost the knob of one of my rotatry valve motors (ARA600) and it is woth of 25 bucks as a replacement part. So I decided to give it a try to design my own and print it. This knob does not fit the valve directly without motor unit. I'll…
can be printed together the model needs to be glued together or separately in other colours can be printed without support the A6M Zero is very realistic Print in place kit card , Assembly required
This ignition coil adapter can be used to mount a standard Honda/Kawasaki/Suzuki/Yamaha ignition coil on the original mounts of a 1968 BSA A65. The ignition coil will be placed tight at the frame so that it can be fully covered by the…
I converted the pdf file into an svg file. And in fusion 360, I just made a sketch of the svg and extruded with 0.2mm. I have also attached the f3d file in case changes are desired. On my ender 3 V3 SE I printed with the help of Cura with…
an A6 flashcard holder that has a sliding lid and is just the right size to take up the least amount of space possible
Combine 65W charger with 6000mAh power bank back to back. 酷科 65W 饼干 + 6000mAh 移动电源背靠背。
I'm including three STLs for tabs (center, center-right/left, and right/left), but the main functionality is hidden in the included OpenSCAD-file which allows you to customize the tabs with your own text or SVGs (I'm using icons from…
I bought a Goex + OLED display from Centuriontech. Like everything I have received from there it is excellent but the filament used to print the housing for the OLED was not a great match for my case. I have a good opaque white PLA that…
UPDATE(Feb 10th 2018): Well, I see that this got lot of attention since I made this, had to print one for someone so I decided to tweak my design a little bit, now you can screw the brace into a table or something, I'll still keep all my…
The part number of the w639 glove storage compartment is A6396800291 You can buy a replacement compartment for roughly 120€ from ali express sellers or 250€ by amazon sellers. But we are here for nifty DIY solutions, right? This Repair…
In my search for a 3D Printed keyboard case, I came across the WhiteFox by @Matt3o. He has many build threads and videos that are extremely useful and has inspired me to try my hand at hand-wiring my own from scratch. I loved his WhiteFox…
If you only print one side of the paper from your printer, you don't have to crumple it and throw it away. You can tear the paper into A6 and A7 sizes. Then put the paper with the clean side up in the recycler. The paper can be used for…
Height is 3U. Fits in the ~9cm high IKEA Alex drawer (804.854.23). Has clearance with attached eye-piece.
*** Please compare your SmallRig Cage for Sony Alpha 6000 with the one in the images, there are different versions! *** I used ‘Fuzzy Skin’-Modifier in PrusaSlicer to achive a more grip surface texture. If you wanna add your own modifiers…
The Audi A6 wheel hub cover is a sleek, modern component designed to fit the center of an Audi A6 wheel. The design comb
Samsung Fridge Ice Dispenser Lever - DA66-00196 fixed.
Uses Phoenix-Prints' design: https://makerworld.com/en/models/938312#profileId-903531 Needs a lot of supports, organic are not too annoying to remove. Version on pictures is 30 degrees. UPD: I've been using it almost daily for months now…
Sick of dealing with tangled cables when using your Dell charger? Does your charger cable constantly unravel in your bag, creating a mess? This 3D-printed cable organizer is designed specifically for Dell power adapters, allowing you to…
![Spur Gear 87 Teeth [PA66-GF33]](https://media.printables.com/media/prints/18de51c7-c35c-4f10-aa63-d9f11ac6b88f/images/12719043_40f450e4-1db3-43a0-bbf2-a07e8c7b8a00_cda1cf18-3f00-42fb-af82-e866f630ca74/gearpic.jpg)
