Liczymy pasujące modele…
Benchmark model should be placed as it is and it should printed in vase mode or with high percentage of infill for higher difficulty. The base circle has diameter 20mm and it expands to 50mm. Model is 180mm tall with 10mm safety borders…
To execute the test, you need to insert the Test_OBJ in the Adhesion_Testframe. Then you hold/stand on the frame and bull on the Test_OBJ until it breaks. I use a bow scale which saves the maximum force after the part breaks: szdc88…
After receiving a new printbed, the adhesion seemed much stronger than I remember, I 'designed' this model to help show off as less of a test and more of a demonstration of abilities for strong adhesion. I printed these without issue on…
The original caps on 3DLAC Adhesion Spray easily cracks. They are also made with PP and cannot be glued back using regular super glue. Here is a handy replacement. Modelled in Autodesk Fusion 360 and fits perfectly!
quick adhesion layer test for the ender 3 v2 or other printers with a print bed with 125x125mm bed. its very useful, so i wanted to share.
easy 1 layer adhesion test fo the creality k2 pro. The dimensions should be a little bit smaller than the plate.
This model just prints two discs in all possible combinations of the 5T Prusa XL. I had problems with the adhesion of some PLA+ / PLA pro / PLA plus filament combinations of different providers. Also this will help detect whether your…
I created this model as quick test that is larger/more in depth than the included bed leveling test in Prusa firmware but still smaller/quicker than most tests out there.
I've had many failed prints due to a single part coming off during a large multi-part print. It's taken me too long to realize that there is a very simple solution to many of these bed adhesion problems if you just add these helper discs…
The Ultimate First Layer and Adhesion Calibration I designed this model to test several calibration and adhesion aspects like for example: Nozzle Offset Adhesion Roundness Small-feature performance Also it gives you an indication for…
Tired of dealing with scattered dust and cleaning up after drilling some holes at home? Have a look at my dust collector/catcher designed for self-adhesion and effective dust capture. It works with most vacuum cleaners, making your…
this model is meant to test bed adhesion and overhangs.
A fairly brutal adhesion and overhang test designed for the new super tack build plates.
Bed adhesion torture test. Tests the bed adhesion in all four corners of the bed and can be scaled to fit different print beds.
Description This Hip Replacement Stem Test Print is more than just a calibration tool—it’s a functional test of your printer’s limits and a nod to cutting-edge orthopedic design. With a unique geometry inspired by advanced hip replacement…
Simple and effective warping/bed adhesion test.
Wall thickness test designed for 0.4mm Nozzles This model is specifically optimized for 0.4mm nozzles, ensuring accurate and reliable results. The wall thickness progression is based on the typical extrusion width of a 0.4mm nozzle, which…
Wall thickness test designed for 0.4mm Nozzles This model is specifically optimized for 0.4mm nozzles, ensuring accurate and reliable results. The wall thickness progression is based on the typical extrusion width of a 0.4mm nozzle, which…
To execute the test, you need to insert the Test_OBJ in the Adhesion_Testframe. Then you hold/stand on the frame and bull on the Test_OBJ until it breaks. I use a bow scale which saves the maximum force after the part breaks: szdc88…
This is a model that you can print to test your printers bed adhesion to the limits. It includes a vertical and a slanted version. As well as a short and tall version. Feel free to tweak the settings as much as you want. Happy testing! :)
Size up or down to your liking, however sizing up will help with adhesion.
FINALLY! I can print more than 2 or 3 of these clips without an adhesion fail. I print these bag clips when I want to finish rolls of filament, then I give them away to friends, family, or anyone who shows interest in my 3D printers.…
The Shrimp Spermatophore Adhesion Apparatus is used for testing the adhesion or stickiness of spermatophores. As seen in the figure, the glass plate configuration is slid into the holder and the force gauge is hooked onto the other side.…
Just a few simple cylinders to help keep finicky corners down on the build plate if they're misbehaving. Some slicers (like PrusaSlicer) have this function built in, so you should use the native functionality instead. Usage Import your…
Let me know how many levels your printer reached !!
This is an upgraded base for the Xiaomi Mijia Night Light 2 that replaces the original magnetic cover and offers a much larger adhesive footprint for reliable mounting on textured or uneven surfaces. Now available in three variants so you…
A simple remake of Mercury one Frontplate. The fine grill replaced with a broader cross. I made it because i had problems with printing the very fine mesh on my glass bed.
A simple adhesion and warping test that is parametric in OpenSCAD. Place “mainpart.stl” and “adhesion-warp-test.scad” in the same folder. Set the base_length (the length of the block that is printed on the bed) and the level (the highest…
Had some problems with some filaments not sticking to bed, so I made few benchmark shapes and sliced them in 5*C intervals between 180-230*C Some times the temperatures given in box are not the best ones ;) Files are sliced for Prusa…
This is the world almost famous adhesion test. As seen on REDDIT, in r/3Dprinting.
if you have any other questions feel free to message me through printables I used the orca slicing software with the marlin generic gcode If you likethe file consider following my page I will be designing more accessories for the printer…
rectangle 1 layer thick to test your bed adhesion and clear off residue from print bed infill-100% Supports-no Rafts-no
The purpose of this test piece was to assess flexible‑filament adhesion on PETG and to review the ring’s deformation properties when printed with Colorfabb Varioshore at maximum foaming. I have included the 3MF file as a starting point…
Simple calibration card to test your filament flow and adhesion. STOP LOSING MONEY ON FAILED PRINTS: I use this card to test new filament rolls before committing to big prints. I realized I was losing 15% of my filament on tests and…
In the photos, you can see a print made with ASA filament at a bed temperature of 100 °C and 110 °C.
This is a holder for Bed Adhesion sticks. It is sized for a Magigoo 50ml stick but will fit a Kores or Elmers stick as well. Sticks are angled at 45 degrees so the rack can be mounted to the wall easily with command strips. Attribution:…
Test your bridging/cooling settings! Check if your bed adhesion is good enough for small footprint parts. Prints in minutes and uses less than 1 gram of filament. Category: 3D Printing Tests
After receiving a new printbed, the adhesion seemed much stronger than I remember, I 'designed' this model to help show off as less of a test and more of a demonstration of abilities for strong adhesion. I printed these without issue on…
The original caps on 3DLAC Adhesion Spray easily cracks. They are also made with PP and cannot be glued back using regular super glue. Here is a handy replacement. Modelled in Autodesk Fusion 360 and fits perfectly!
ACPS First Layer Adhesion Test Model 220x180mm 0.1/0.15/0.2/0.3mm layer heights
This is a test I used to fine-tune my ASA printing, squish and flow rate Print Settings Printer: Voron 2.4 Rafts: No Supports: No Resolution: - Infill: Filament: - - Category: 3D Printing Tests
quick adhesion layer test for the ender 3 v2 or other printers with a print bed with 125x125mm bed. its very useful, so i wanted to share.
easy 1 layer adhesion test fo the creality k2 pro. The dimensions should be a little bit smaller than the plate.
This technical model is designed for a two-stage validation process in the maker workflow. It allows users to calibrate both the mechanical bond to the 3D printer's build plate and the chemical bond of post-process coatings Stage 1: Bed…
A fun (or maybe not so fun) way to discover the truth about your 3D printer's adhesive abilities. Not long from now, I will post a picture here of what my 3D printer (AnkerMake M5C) comes up with. If you print this, then please leave a…
Please give it a ❤️ if you like it 🥰 I designed this model to compare the adhesion of different 3d printer beds. Video FR about it: Please give it a ❤️ if you like it 🥰
Pretty simple cylinder. Good test to see how well your prints stick to the bed. Use the 40mm tall one to test various temperature settings and/or other settings until you find the one that sticks nice and firm to the bed after the print…
Remix of the Prusa Face shield and 3-hole variant. This adds a 0.6mm pad at the end of the headband to help with adhesion. Three hole original: https://www.prusaprinters.org/prints/26610-face-shield-3-holes RC2 original:…
CHANGELOG: 4/2/2020: Updated the model to have more support between bands. This makes it a little harder to pull apart, but ensures that the bands adhere well to each other, as I found that some layers would not adhere and cause stringing…
These 0.2mm high, 2D sine waves based on https://www.thingiverse.com/thing:11243 are for testing bed leveling and adhesion. Since the printhead is always changing direction during the sinusoidal motion, poor adhesion will show up quickly…
The higher you print it, the heavier it gets! Test your bed adhesion with this. Play with your fan speeds, your heat settings... see what works! The higher it prints, the more it pulls on the bed. Measuring gauge on side in 25mm steps.…
Don't know how good your adhesion is to your bed of your printer. use this to figure out your settings to make a better bed adhesion to your 3d printer without using brim. enjoy and let me know how high you were able to get. can be cut to…
Test your bed adhesion with this fast and simple test. Print with spiralize/vase mode. LH 0.2 30mm/s (or slower depending on your cooling capacity) ~25min print. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
A simple print to test the adhesion strength of glue on different kinds of filament. Print two of the testers in the filament you want to test. Put some glue on the bottom of the testers and stick them together. After the glue is dry, see…
This model is designed for printing with a .4mm nozzle and .2mm layer height. It's a great way to diagnose and calibrate things like nozzle offset and fine details as well as overhangs and retractions. I printed my test on a direct drive…
I have scoured printables for the different lucky 13 hand gestures that have been made so far. this is primarily a repost to put all of them in one place. I'll continue to update this list as new ones come out. Each file is a pair of…
Calibration Test Circular – Retraction & First Layer Check 🎯🖨 Not sure if your 3D printer is calibrated correctly? This Calibration Test Circular is here to help! 💡 Test your printer's retraction settings and first-layer accuracy with…
This is a qualitative layer adhesion test. If your trying to get the best layer adhesion in your prints, you can use this model to look at the failure mode of your layers. Ideally, you are looking for a cohesive failure where the part…
Tired of using boring and easy to print calibration cubes? Now you can use a brand new B.A.T.C.H. ( B ed A dhesion T est and C alibration H exagonal-polyhedron) You will test your bed adhesion with a small area of 66.725mm^2…
This tests the adhesion in a few more spots, to better fine tune the bed levelness
This is a quick test I designed to test bed adhesion. There are some crazy tests out there that'll determine holding power and such, but I just wanted something that would replicate the sorts of issues you might run across in everyday…
When I routed my Network Cable through our apartment I simply forgot putting something over the drill holes BEFORE putting the cable through. Therefore I had to devise a model that allows me to run the cable through while holding firm…
If you like my design you can support me on BuyMeACoffee - https://www.buymeacoffee.com/kaushikbm -------- Many a times while printing small objects we face difficulty in making them stick to the bed and keep it there. These anchors are…
Print in any layer height that will print only 1 layer (the model is 0.2 mm tall).
Funny little mould for pressing sand, makes the text "THIS LAYER ADHESION SUCKS" in the sand.
Simple but effective bed adhesion test for your 3D printer to verify if your bed leveling is correct. The model is shaped to be only one layer tall so you can peel it just right off and not waste material. The xy dimensions are calibrated…
Easy to print Test print for bed adhesion This is a good test print to check your bedplate. Settings: 0.1 - 0.2 quality 100% infill PLA No supports Njoy
I wanted to test adhesion properties of various materials on different sprint steel sheets, and I needed a model to do that. Thus I designed a star with narrow “arms” that also has a hole, so you can hang it somewhere as a decoration once…
I noticed, that the inbuilt brimears in some slicers are far too weak. So I designed some more durable, which can be merged with the model. Included are versions with 0,4 and 0,6 mm height. I recommend the lower one, it is strong enough…
Remix of InstantBenHur. Many thanks for the awesome design & providing the .step file. After I already printed three of the original models I noticed some possible improvements so I changed it to be Easier to stack (1cm taller) Faster and…
simple print bed tab designed to improve adhesion for prints with sharp corners and reduce warping during printing. These tabs can be added in your slicer to help anchor models to the build plate, especially for parts with small contact…
This little benchmark print helps you to figure out how well sharp corners stick to your printbed. Both the inside and outside corner are filleted with a different radii. The size of each radius can be seen on the adjacent face. Overall,…
Super quick and simple print I recommend doing after you first setup a new resin printer. Simply duplicate the raft out to line the build plate like you see in the image, and print it off. I recommend keeping the slice file on your USB so…
I've used this part to test ZillaGrip on my steel FlexPlate. More info in my video: youtu.be/IrL0kZ1LjYo It's a copy of Toms design used in his video about Grocery Store Bed Adhesives:d youtube.com/watch?v=MAw2FK8y5i4 Print Settings:…
What you see is what you get. :-) Data: Build plate adhesion: Skirt Number of lines: 4 Daten: Druckbetthaftung: Skirt Anzahl der Linien: 4 Print Settings Rafts: No Supports: Doesn't Matter Resolution: 0,2 Infill: - Filament: all Category:…
after 8h of printing i saw that 2 parts havent enough Adhesion, so i added a hardcoded brim like in the orgiginal files from Popandsicle
overhaulin the connection for better stability
I designed this in tinkercad. Print without supports to see if your printer is dialed in with bed leveling
This project started as a simple desire for a versatile vase test for my 3D printers. In collaboration with Gemini AI, I generated OpenSCAD code to create a unique twisted square vase. The design comes in two variations: Normal Vase: A…
A 3D-printer torture test. Highlights cooling, overhangs, stringing, bed adhesion and more. Please note that this is not an easy print, ensure proper bed adhesion before attempting this. I wanted a model to use while finding the optimal…
This model just prints two discs in all possible combinations of the 5T Prusa XL. I had problems with the adhesion of some PLA+ / PLA pro / PLA plus filament combinations of different providers. Also this will help detect whether your…
A simple test to check the bed adhesion and shrinkage of your filaments. I designed the model so that it should definitely lift from the bed. I wanted to test how much different materials shrink and how the enclosure affects them at…
Printable sheet to test the adhesion of your 3D printer bed sheet throughout it's entire area. Multiple files provided for the following print area sizes: 200x200mm 220x220mm 220x300mm 230x270mm 235x235mm 250x250mm 255x255mm 300x300mm…
Supports are recommended, ender 3 completed multiple prints without supports and quality was fine one side for light, other side for tape or magnets 1mm inside
Hey! I've been having some adhesion and levelling issues with my print bed and so I created this that shows me where on the print bed I have issues. A bit of trial and error, change settings in those locations and I was back to printing…
This test print evaluates your 3D printer's bed adhesion. If the hinge falls out of the glasses when you remove them from the build plate, your printer has failed the test. To address this, either clean your build plate thoroughly or…
I made this model to test my adhesion of small surface areas. Extremely hard (for me at least) to get to work. See how high you can go and share your settings. I have completed it myself after a fiddling a bit. Maybe I'm a noob, show me…
When I build prototypes using FDM, I sometimes experience delamination and breakage of my 3D-printed parts. It is not always possible to rotate the part to optimize strength, which can lead to adhesion and delamination issues. I have…
![[Adhesion Fix Remix] Cam lock bag clip](https://media.printables.com/media/prints/0e68c640-31dc-4903-aa81-c039838a7716/images/9799190_0508c4ff-d768-4110-88d8-562f610ca2ef_2d139680-28fa-430c-beaa-4cc2ff118352/20240225_180635.jpg)
