Liczymy pasujące modele…
Required Stls: 1x hinge_upper 1x hinge_lower 1x arm_upper 1x arm_lower 2x nut_block *4x plastic_spacer *The plastic spacers go in the glass cutouts to align the panel and prevent the metal screw from touching the glass. Required Hardware:…
[5 Dec 2023 short update] Known Issues: A.) This is designed for K1, I don't own K1 max, not sure if it will fit, there are K1 max version 270 hinges done by others also available on Printables. B.) PLA will work, but recommend PETG or…
This is a simple yet versatile parametric 90 degree bracket. This bracket can be re-sized for virtually any need via the OpenSCAD parameters. The bracket can also be set to 3 different styles; Normal Bevel, Low Poly, and Extra Low Poly.…
Tried to adjust the Z-mount and the 90 degree extruder so that another chain can be attached in X-direction. Unfortunately I only had the STL files available, so there might be small errors in the mesh. Didn't want to re-model the model…
Made this 90 degree bend to prevent the bowden tube on the K1 Max from rubbing under the lid, it also provides a cleaner movement of the cable chain. It's loose enough that it shouldn't cause any problems with under extrusion. Made…
Simple drill and screw guide. Helps to drill perpendicular holes and screws. Tested over with my pergola project. Works fine. Super easy to get 90 degree angle. Scale for smaller objects. This one is designed for long (30cm) drills.…
I CANNOT SAY THIS ANY SIMPLER. I'M WRITING THIS IN UPPER CASE SO THAT WHEN SOMEBODY SAYS ‘I DON’T UNDERSTAND WHAT I NEED TO PRINT' I CAN SAY IT'S ALL IN THE INFORMATION PAGE. AT A BARE MIMIMUM, EVEN IF YOU DON'T READ ANY OF THE MAIN TEXT,…
This design supports material from 5-15mm thickness. The clamps are more easy to handle than angles with seperate clamps, but will only support joints of equal thickness material. Concept is based on idea of takuwoodcraft / TWCDesign.…
This door holder is specifically designed for the Elegoo Centauri Carbon enclosed 3D printer. It allows you to securely prop the front door open at a fixed 10-degree angle. Purpose Provides slight ventilation for the print chamber when…
Wandhalterung für den Bosch 4A e-Bike Charger (Smart System ab Modelljahr 2022 BPC3400), Befestigung mittels 2 Senkkopfschrauben ø 4mm.
Introduction Inspired by "Cable Corners... keep cables in corners!" by muzz64 on Thingiverse Fusion 360 parametric design This is for bend-sensitive cables, such as Cat 6 and Cat 6A. In the case of these cables, the curvature of the bend…
Sometimes all you need is a 45/90 degree tool for tracing and cutting. It is a 2 piece tool that is a must-have in any Carpenter toolbox. You can use them combined and it is good to join wood planks at 90 degrees or to trace lines tracing…
This is a remix of Helasius drillguide - https://www.thingiverse.com/thing:4839621 However, I needed it to be able to drill on a square corner. As per the original description, it fits sizes 3, 4, 5, 6, 8, and 10, with holes at 90º and…
This is a remix of: https://www.thingiverse.com/thing:3644062 I liked the design of the original bracket, but wanted to try and make it a little smaller. This design is about 50% scale of the larger bracket. Included is both a 2 bolt and…
Still requires print supports on the part where the hot wheels track clips in.
TL;DR: Print the top, print one of the two bottom parts, and optionally print the cable holder. This heatbed cable cover and holder is based on the original Prusa part. It keeps the exact dimensions for hardware, LED viewing window, cable…
My own Hot Wheels track piece, Something I felt was missing from what is sold. Works with most cars at medium speed, just don't overdo it. Connects to any Hot Wheels track with a connector, both my connectors and the Mattel ones work.…
!!Important!! I highly recommend straightening the Z-Axis gantry before doing this mod, as explained here . The Ender 3 V3 SE/KE faces a significant issue with a wobbling frame, which can result in serious quality problems, especially at…
I have designed this profile for LED strips up to max 15mm wide. The beam angle is 45 degrees, making this profile perfect for indirect lighting. The fit is perfect and the diffuser snaps into place on the side without the need to use…
Based on the original Thing from K_Lab - thanks for the source Fusion 360 files: https://www.thingiverse.com/thing:3533859 and the remix from Theo Tinjum:…
Needed a grip that was more vertical. This works. Print it upside down, minimal support need for grip cutout area. If someone is more capable than me, it needs some texture added. I printed with low resolution to simulate texture. It's…
Classic protractors use verniers (nonius scales) with 2, 5 or 10 minutes marks (0.033, 0.083 and 0.167 degrees correspondingly as one minute is 1/60 of a degree). Modern CAD software deal with decimal values of a degree so I made this…
I have .3mf files with my settings I've used over at Makerworld . To split the model into each individual object: (In slicer) Right-click model → split → to object Designed for a full size ATX PSU and a dual PCIe bracket GPU GPU size…
The original design was a nice start / frame, however, I thought it would be an improvement (and a big savings on filament / print time) to add honeycomb cutouts, a 45° front angle (to match the OEM front panel angle), & added the PRUSA…
I use this for my 3D printer enclosures - sometimes you want to open the door and get it out of the way. The mounting holes are for “6 gauge” or 4mm countersunk screws, the pivot is M4x30 cap screw (if you get a longer one with an…
I HATE PROTRACTORS ALREADY! I printed so many prototypes and spent a lot of time and plastic to find the best tolerances. I'm really tired of them! Anyway, here is a professional version of The Smallest Protractor . It is bigger as you…
Material: PET-G Layer high: 0.2mm Perimeters: 4 (5 for connector) Infill: 30% Cubic Holes for connectors are blind because of reliable printing. Drill them by 5-5,5mm drill. Big square is modifier - you can set bottom layers to 0, it…
need 4x m3 insert nut
This is a drill guide to aid in 90 deg and 45 deg drilling. Diamond cutouts are on either end to aid in finding measurement lines. The 45 deg guide will intersect at the the center line. All holes accommodate imperial bits. Please be safe…
Basic 45° small double switch track compatible with Brio, IKEA Lillabo (old plastic dogbone and current wooden-only version too), Thomas Train, Kaufland, LIDL Playtive, kmart, ebay,... wooden tracks. Support: NO, Infill: 15 %. CHECK OUT…
update 15-02-2024: added stl file without the support enforcers and original Freecad file 180degrees curve compatible with the orange Hotwheels track. to connect it to the track, 2 standard hotwheels connectors are needed. there is no…
i have 2 versions. 1 with 5.5mm holes for m4 brass inserts and if you don't have inserts you can pick the no insert version with 3.3mm holes so you can drive m4 bolts in it. i printed it on 0.24 layerheight 210/50 pla+ and 50%infill with…
I got annoyed by not being able to either print of fit the 90º heat bed covers for MK3. So I took inspiration from the last model that I've tried and built my own version from scratch based on the original Prusa source files.
Adapter plates for allowing K1C and later releases of the K1 to use my 270 degree hinges. ----------------------------------------------------------------------------------------------------------------- These two (small) side panel hinge…
Modern and functional desk accessory designed for FDM 3D printing. The 45-degree tilted body and geometric perforated structure provide quick access to writing tools while maintaining a clean, contemporary aesthetic. ☕ Personal &…
Wandhalterung für das Ladegerät vom Audi E-Tron. Ladegerät kann entfernt werden, ohne die Halterung zu lösen. Kein Support notwendig, keine speziellen Druckeigenschaften notwendig. Wall mount for the charger from the Audi E-Tron. Charger…
90 degree PTFE tube guide. Together with the guide, I used https://www.crealitycloud.com/model-detail/657e19d8937557724252afab , reducing the height to 50% and https://www.printables.com/model/734259-creality-k1-k1-max-ptfe-tube-holder I…
This is just a remix of cuzzea's work, eliminating the colder temps that won't work for my PETG (Hatchbox). This one goes 220-260, use cuzzea's exact instructions for setting up the post processing script. Nothing changes except the top…
Holder for Type 2 charger cable where the cable come in from the side, better fit how the cable is looped around the holder. You may want to print this with supports. Edit: I've added a picture of the areas that you may want to have…
This project had two inspirations. The “Serious Clamp It Square” by J-Max is amazing. https://www.thingiverse.com/thing:1306832 This thing is stiff, which is needed for clamping. It is large and feels strong when you hold it in your…
Material: PLA or PLA+
Semi Circular Protractor 180 Degree Angle Ruler 0 to 9cm and 0 to 150mm Type: Protractor Size: 150 x 94 x 1.50mm
The existing spool holder of the ender 3 V3 SE added to the shaking of the Z-axis to reduce shaking and enable better filament supply by rotating the direction of the spool holder 90 degrees. material 1. M5 nuts x 2 2. M5 x 15mm = 1, M5 x…
This is a remix of the right hinge from MagicShrimp's 270 degree hinge for the Elegoo Carbon Centauri. It is literally a mash of the hinge and the right holder from Julien Mairy's cover and bed holder. I wanted to have both, but they…
360 degrees protractor Type Protractor Size: 150 x 150 x 1.50mm
I love the Lego Wreath and I am in the process of printing more for Christmas. I needed a jig to align my 6 segment wreaths at a perfect 45 degrees. I traced the original Lego wreath branches to make this jig.
Device for 45-degree chamfering of plasterboards in drywall. Small and convenient to useAll trapezoidal blades up to 62mm fit. Chamfer width +- 6mm. The nut works easily after the first screwing in. In the slicer, the model must be…
Less stress on the wiring and more gap for twisting than shorter model. Slightly longer (9mm) but less prone to insulation melting. Modified from original Prusa model files. Use with original clip
Tilt Blocks For Your Bambu Lab A1 Tilts the printer 20 degrees I use simplyprint as my software for auto ejection Print with at least 3 walls and 10% infill
Basic 45° small switch track compatible with Brio, IKEA Lillabo (old plastic dogbone and current wooden-only version too), Thomas Train, Kaufland, LIDL Playtive, kmart, ebay,... wooden tracks. Support: NO, Infill: 15 %. CHECK OUT other…
Fits a 66mm or less wide common sharpening block. Fixed at 17 degrees for easy operation. Very hard edge knives can take a 15 degree edge, cheaper common ones last longer at 20mm. 17 is a compromise angle used by many for a wider variety…
Reupload of a model from Pavel_Sticha (https://www.thingiverse.com/thing:3831760).
I read somewhere that people have had success with removing ghosting/belt lines by positioning the X and Y gantry at 90 degrees during the belt tensioning process. I decided to make a quick model to help hold the gantry in position during…
My new keyboard came without keycaps so I decided to make some. Through a lot of trial and error, I learned how to create some nice keycaps - and that's what this model does. You can learn more about how I arrived at this point and some…
Corner covers: Cover up the gap left from removing the hinges for a better chamber seal. No additional hardware required, just reuse the screws used to hold the original hinges in place. Magnetic Door Latch: Uses 2 8x3mm magnets to hold…
If You find this design useful, Please consider sharing a Make or leaving a comment. It's always good to see my efforts in use by others out there and it often inspires me to make improvements where I can. Without feedback I just draw a…
The 90-degree clamp is an essential tool for any woodworker. This 3D printed clamp is designed to hold pieces of wood at a perfect 90-degree angle, making it ideal for creating precise joints. Whether you’re building picture frames,…
Achieve your ideal setup with the Corner Kit. Use the Corner Kit to angle your Video Doorbell Wired towards your walkway, so you can improve your motion detection and get a better view of visitors coming to your door. Designed by Thom…
I made a fancy fan cover which is designed to optimise airflow. Testing video below explains more! You might also be interested in the 140mm fan insert for tights/pantyhose .
I was looking at the Honeycomb Storage Wall and it looked pretty neat. And so I set in motion the plan to print some honeycomb bits to fit on my wall. So I started out paramaterizing the honeycomb to fit. And I saw someone made pretty…
This is a remix of Jakeleeee's Prusa Mini 48deg heatbed connector cover, which stretches it to be about 3mm longer, to provide the additional clearance that I found was required on my Prusa Mini+ to allow the cables to exit without being…
TLDR:- New Hinge design (V3) allows for quick change V3 face plates/covers while Using V2 additional V2 components for the hinge assembly. New optional tools added. Also includes post processing and detailed assembly instructions (with…
A pottery clay tool designed for quick and precise cutting of clay at 30°, 45°, and 60° degree angles. Things you will need: 4x 4-40 brass heat set PEMs 4x 4-40x.25in screws An old guitar string or stainless steel braided wire both work…
I couldn't find the 90-degree adapter for the Bestway Power Steel pool so I made one. The threads for the connection for the pool seem to be non-standard so I custom-made the threads. The threads are ~109mm in diameter. The 90-degree…
Víčko plechovky piva Pilsner a Kozel , Radegast, limonáda , Pilsner and Kozel ,Radegast , limonade beer can lid
Zeros to about 50m but Elev. and Windage is adjustable. Requires: 1x M2x~10mm 1x M3x~23mm + nut 2x M5x~25mm Not all picattiny is manufactured within the same tolerances thus sanding may be necessary.
I accidently broke my feet on my keyboard, Logitech K850. I couldn't find replacement parts so I modeled these using SketchUp and created the STL files for both the 4 and 8 degree feet. Support is needed for the the pin alone.
I recommend scaling up to 1" on the sides (166%).
I found that all the filament holders out there seemed too complicated for what I needed. So, I designed my own. I designed with a lattice structure so you can get away with the lowest amount of plastic but is still pretty strong. It is…
UPDATE 2025-05-19: I have added 50mm high versions of the 3mm walls models. This makes the tool usable on objects with some unique or non-flat end surfaces. UPDATE: I have updated this design to include 6 different slot widths for both of…
Orient the parts so the flat cut end is on the bottom than print with no supports.
Hey, this is a remix of KYZ-Design's amazing model. It's a Door Hinge which allows you to open a door (for example of an enclosure) 270 Degree. The door hinge consists of 2 Parts. Both of them have counterbores (according to DIN 974-1)…
This model is compatible with the lego system.
The door on the Snapmaker U1 doesn't open much further than 90 degrees by default, and I wanted less restrictive access, so I put together this 180-degree door hinge. It uses compression-style fittings to hold the glass door to the hinge…
Parts The model consists of multiple parts, each is stored in a separate STL file: Sides: Left-Side.stl and Right-Side.stl Back: Back.stl Bottom: Bottom.stl Front versions Front_Blank.stl - without lettering for you to modify (if you…
With this 45 degrees doorbell wedge you will be able to adjust the viewing angle of your Eufy doorbell camera. By adding the 5 or 10 degrees wedges you can extend the camera angle. You will need 2 extra small selftapping screws to attach…
Fixed solid holes on mount Please refer to https://www.printables.com/model/631300-tweaked-cable-chain-mounts-for-elegoo-neptune-4 for additonal parts. I only created to fix the missing holes on the mount.
5cm x 6cm x 3 cm box. The original file I used had sharp drop offs (parts of print with no material underneath). I made sure that all parts of this print had at least a 45 degree build up. added 3 different hole types. ### Note: If box…
Achieve your ideal setup with the Corner Kit. Use the Corner Kit to angle your Video Doorbell Wired towards your walkway, so you can improve your motion detection and get a better view of visitors coming to your door. Designed by Thom…
Toto je tisknutelná skříňová nástavba pro model Praga V3S od Deagostini v měřítku 1:43 nebo pro tento model: https://www.printables.com/model/541730-praga-v3s-143 Soubor STL uvolňuji pod licencí neumožňující prodej. Vytiskněte si ho doma…
The fence size is the same as Timo's, but allows cutting at -45, 45 degree angle. In addition: Added .1 mm to fit more easily Add lock mechanism with 2 M3nS nuts and 2 M3x14 bolt (from the MK3S+ Fasteners spare bag) to lock the track. The…
This is a 45-degree offset picatinny rail that is made to use 3m x 30mm bolts to mount. I used a file by unseenkiller and JPGunCAD (8) Unseenkiller and JP GunCAD - Pictainny Dev Blank (odysee.com) as the base. the rail is 48mm long to fit…
Note: This is the version for personal use ! If you want to print these files for other people, see the commercial version ! Update 2024-11-11 I've created another wheel (V3) to counter some issues I've experienced during previous…
The 270 degree hinges these new pins were designed for are here :- 270 Degree Geared Hinges for K1/K1 Max/K1C. Update November 1st 2024:- added some fatter link/connectors. Originals (by design) were thinner to allow the pins to be seen…
Modellbahn Spur N – Ladegut – Paletten mit Kisten und Fässern gemischt, in verschiedene Varianten. Ich habe nochmals Ladegut für die Modellbahn Größe N entworfen und habe versucht verschiedene Szenarien nachzustellen. Es handelt sich um…
The original hinge (this is a remix) is nice looking but it did not allow for 270 degrees of movement and I could not re-inforce the core with metal, to make very stiff. Also it was very big and I wanted it a bit smaller to fit M3 allen…
For fastening the honeycomb storage wall grid to the wall. This was a simple change from @roryshko's excellent ‘empty’ countersink model to use an 82 degree fastener instead of 90 degree. Also included are through hole versions, all with…
Needs: - two extra M5 (minimum 15mm long) screws for the frame attachment. - four M5 5mm long heat set inserts for connecting adapter and holder. - four M5 8mm long screws for connecting adapter and holder. The original file has been…
Print without support Put wires through the plug from side (like on first photo) Solder wires to USB pincs on pcb Put a drop of glue inside case Push connector inside with little force (table surface can be used for alignment)
Remix with 45-85 deg and 45-70 deg. Category: 3D Printing Tests
Summary: iPhone monitor mount in order to view it in landscape mode to use the Standby features or watch videos, etc. Takes a little over 30 minutes to print on Bambu PLA settings. Description: No need for supports. Fits any magsafe…
I found that all the filament holders out there seemed too complicated for what I needed. So, I designed my own. It is super simple and the rolls don't have any issues spinning on it. You can also add a little Kapton tape to the top edge…
Designed to have a small footprint on the main rail, so that it fits behind or in front of your scope. Specifically designed to fully support the holosun 507 pistol red dot, which has the same footprint as an RMR. After printing all the…
Needed the mounts so here they are for you if you need them also ;-)
Adapter to increase the display angle by 20deg
Edge sanding attachment for a Dewalt DWE6423 (shown). Holds sander at a 90-degree angle to workpiece. The main body is printed in separate pieces to avoid an ungodly amount of supports. You will need supports though. I used a bit of CA…
This model is compatible with the lego system.
I really liked haitonno's design for this drill dust collector, but for some reason, it was "upside down" from what my Dyson would need. So, I flipped the button/lid around. Much better. I printed in 0.3 resolution, and the button broke…
Just a simple universal design corner clamp that i use for my woodworking jobs and it can also be used as a distance keeper for furniture building. For good resistance if you plan to use it a lot in the workshop, i recommend printing it…
help with your shelves
![Bosch Indego S500 rear wheels V1 [personal use]](https://media.printables.com/media/prints/262266/images/2341224_aa5cc481-3db9-4bf3-88bd-520463c2462d/img_7759.jpg)
