Liczymy pasujące modele…
Originally uploaded in 2015 to another sharing site, this design has been downloaded 6000+ times. I originally printed in ABS, but PETG or PLA+ should also work for the structural integrity needed. This is based on the original Flite Test…
I found this on Thingiverse, and thought that I should upload it here. "Found out what the range was on my transmitter unfortunately and crashed my Apprentice STS. Never liked the stock cowl design so I came up with this. Use a 10% infill…
Two piece interlocking copy of the Swappable Power Pod and FT firewall originally designed by Josh Bixler. Three piece option is there if you would rather use your own firewall. (Not sure how well the PLA is going to stand up to motor…
I found this on Thingiverse, and thought I should upload it here. The original file was created by sutekh, but it was broken, so Rickmcolorado repaired it. Here's the original post: “A friend with an Apprentice needed a bulked up motor…
The Twin Timber is sold with molded plastic 3-blade spinners. As Henery Ford said, "You can have any color you want as long as it's black." I wanted colors. Many have also found that 13x4 2-blade props work fine with the Twin Timber. I…
*** If you like the file please make your “ like ”. Every mark helps me to get a free roll out of Prusa. Thanks…. *** I re-sampled the original cowl so it would match and fit the original on the E-Flite 1.5m Texan. I added a support ring…
Elite Test Swappable Firewall, it is 5.1 cm wide by 4.35 cm tall by 2.4 mm thick Category: R/C Vehicles
Used to make foamboard RC planes, just add an M3 bolt and nut and utility knife and you will be cutting perfect bevels!
Flite Test Mini Power Pod for the Power Pack A components 12x16 mm hole pattern for an Emax MT1806 motor Dovetail joints at the seams Designed to be printed flat and then glued Printing flat allows layer orientation to optimize strength…
A printable 3d model designed as a spare part for the original nose cone of the Eflite Viper 90mm. The model consists of two parts: The nose cone with sockets for magnets The base plate to be glued onto the fuselage The nose cone can be…
Use this to enable aligned drilling of the Flite board prop to 12mm, the guide should clip over the prop and maintain the drill bit alignment. Mark the bit depth at 110mm. The 6 holes on the side of the cone are for optional hot glue to…
Easily 3D print flite test kit parts at home. No need for a laser cutter. I have also designed a full power pack motor mount that can be printed in place for a much easier and more durable assembly.…
I fly out of my back yard and use my lawn for a runway. Even cutting the grass very low with stock tires means the prop is doing some mowing of it's own. While not elegant these wheels get the job done. The wheels are 80mm in diameter…
For 9mm blades. Use M3 screws & nuts Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Filament: 3D Ware PLA Category: Hobby
This is a magnetic funnel for my Rancilio Silvia Espresso machine. I've been using it successfully for the last 6 months and vouch that it works as needed. It uses tiny 3 mm diameter x 2 mm high magnets, 12 of them so that the grip is…
Upgraded landing gear brace for the Horizon E-flite night Timber X. This replaces the original blocks that hold the landing gear to the fuselage. I used PLA+ and have never had a failure as long as it was printed in a vertical orientation…
Yet another version of the FT Elements Simple Firewall. This one prints quickly and assembles just like the laser-cut wooden original. Just add some CA glue and go crash something. Instructions I print using ABS at 100% infill. CA glue to…
This is a modification of my Super Bee power pod . For the Super Bee there's a downward angle required for the power pod. For other models such as the FT Arrow the power pod has a 90 degree angle instead. Since I'm currently building a…
You can put these in your Flite test planes instead of the laser cut ones. This is version 2 with more accurate dimensions and proper thickness. (I got better at 3D modelling) Print settings: 0.2 mm layer hight is good for the strongest…
Po vytisknutí se odštípne podstava u špičky a je to. Tisk bez podpěr. Upravoval jsem středovou část a takhle mi to sedí.
Just add a microservo to the build. You can see and customize the releaser here: https://cad.onshape.com/documents/a2fad6d0cf64304307fcdafe/w/76f1b029aa6d6f58a28d5f7e/e/e2aaab103ed4d49d56a2d02a The wishbang you can see on the picture it's…
Eflite Payload release hinge and missiles all files are here feel free to create and design your own missiles with the release mech, just please add to makes if you make something or remix
Flite Test Logo stencil for spray painting or airbrushing. Print instructions Category: 2D Art Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: .2 Filament: Hobbyking PLA Notes: At .2 resolution this…
test perfil alar top flite sierra entrenador de 1200 mm de envergadura resolucion 0.44 un perimetro 15 pociento de relleno velocidades segun material.
The original Timber wheels have a habit of tearing away from the hub over time. These replacement wheel hubs grip more of the tire and should prevent the issues in the future. They also prevent the tire from rubbing on the landing gear.…
This is a battery holder to mount to the bottom of the power pod used on a variety of Flite Test models. I'm using this one on a bloody baron. You can attach it to the bottom of the power pod with double sided foam mounting tape or hot…
An improved firewall for the standard size Flitetest power pod (for Spitfire, Mustang, Simple Cub, Corsair, etc). I have included motor mount holes (1.2mm diameter, 34mm PCD). There is a hole at the bottom to feed your XT60 connector from…
Need a way to secure your battery in an RC aircraft/plane, boat, or car? This battery tray can help you do that, it hold
This is the control horn for the Flitetest mini airplanes. http://store.flitetest.com/aircraft-accessories/ Category: Hobby
You will need a small screw to secure the spinner onto the motor adapter. I also recommend printing the adapter in TPU.
Fix your E Flite Mini Apprentice RC model after a hard landing. Print these parts in a few minutes and up in the air again without spending money for such a small part.
Use supports for the top lid. You need to open the access ports necessary for your setup with a N#11 Xacto knife, for example throttle, right aileron, Sbus an DSM Satellite, this way ports you do not use are covered. Close with 4 M2x10…
This a replacement part for a RC airplane model that broke after a minor crash. The part is available form the maker, but it is sold as a larger kit and is expensive. The part was not difficult to design and costs little to print. If your…
For the stock version of the 10.5 / 8 - 4 blade propeller You can buy the propeller from banggood for a much cheaper price. The banggood version seems to identical to the stock one, except that it doesn't have yellow tips. Alternatively…
The firewall is not available for purchase from horizon hobby except as part of a whole fuselage. My plane was fine except for the smashed motor mount and firewall. So I designed this printable replacement firewall. It is compatible with…
Mount for the FT EZ ID Remote ID Module. Not perfect, but it's functional. I'll clean it up at some point. Remake from the QAV-S files on thingiverse. Print without supports, bottom to plate Use two zip ties to attach to drone
This has been designed that no supports are needed. Make sure when importing that the face is flat on the bed. Please comment if anyone has any ideas to make this better
Eflite Extra 300 Spinner Without Back Block İnfill 0 wall layers 1 Using Simplify3d you can print the first 20mm and the
My original nose is a bit squished and was heavy anyway. This one is significantly lighter because the wall is just .4mm thick, can be slightly dented to the side, but also goes straight back to its original state. PLA is supposed to…
I am doing a Canadian livery on my Eflite AT-6 and wanted an exhaust pipe to help it look more scale like so I designed this. Printed @ 20% infill with supports “ touching build plate only”. Print it laying down as shown in the pics.…
I kept breaking the spinner cap on my E-Flite Apprentice. I would have to pay $5 each time and wait for it to be shipped out, then I remembered that I had a 3D printer. I just recently uploaded the base as well. The two pieces are…
I got FT legacy V2 plans but couldn't find printable STLs for landing gear, so I made my own version. The main difference is that it also includes mounting root piece with holes for brass inserts for easy mounting/disassembling. Should be…
A 3D printable, simplified firewall for the Flite Test Tiny Trainer . The original is made out of wood, but this works just as well! The hole in the middle is for the shaft to pass through and the four holes on the edges are for screwing…
Tested on Z Offset (4x 1" diameter wheels with these hubs), and First Strike (2x 2" diameter). Both bots have well protected wheels. Across 10 regular combat matches and 2 rumbles I had no issues whatsoever, although they probably would…
Complete power pack motor mount to be used with the flitetest foam core models. Much more solid than building out of foam core and wood. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: R/C Vehicles
Should work for the new version of p51d as well. This is a 2 blade spinner for APC 12 inch blade, I only have a 12x6 blade, but it should work for 12x7 or 12x8 as well I think. According to my calculation 12x7 or x8 should provide similar…
This landing gear is printed in one piece with no supports (front face down on bed). It has the same rubber bands I use to hold the wing on as shock absorbtion and there is a living hinge designed into the print to allow it to flex where…
Eflite Extra 300 wing tip protection Print Settings Rafts: No Supports: No Resolution: 0.22 Infill: 100% Filament: 1.75 PLA YOUR COLOR Category: R/C Vehicles
These replace the foam motor and pipe power pod supports on the FT Mini Scout by Josh Bixler. Holes for bbq skewers are set to 3 mm because that is the size I had. YMMV. I think they can be safely drilled out without affecting too much…
Clip to hold the hydraulic break cable in place on the top-tube, fork and seat stage. Made to fit Canyon inflite from 2016.
The Flite Test Sea Duck is one of my favorite planes but I find the opening in the top rather small and inconvenient. This requires a slight alteration to the plans. I basically hack off the front of the foam board canopy and put this in…
Update: tray_2 For E-flite P-51D Mustang 1.2m, might fit other e-flite warbirds as well. Fits larger battery, should be able to fit 35mm x 45mm ish Clip the original retaining clips on the rail. Remove the wooden plate Put battery tray…
-I improved the nosewheelframe because it was too weak, now it withstand an rough landing. This is an improved landing geaf for FT Guinea Pig. It looks more like a cargo plane and the nose wheel isn't that fragile. Print Settings Printer…
E-Flite BL50 motor & ESC mount with ventilation and air scoop with cowling. Specifically designed for my highly modified Sig Kadet Senior electric conversion. Could be used on other planes that it fits onto firewall. V1, V2, V3 uploaded.…
This is my 3rd version of landing gear for the E-flite Opterra. Version 1 and 2 used double sided tape to attach to the unmodified keel of the plane. On a semi-hard landing I managed to break the plastic keel instead of having the tape…
I broke the internal part of the Nose gear for my EC-1500 (the grey part inside the battery bay), and the part is o back order for 5 months, so I decided to try to building a replacement; this is the result I did some improvements,…
FT Mini Arrow Power Pod. This power pod is for 2204 2300kV motor for a fuselage modified to fit a 1500mah battery. This fits snug into the fuselage allowing a good friction fit. I also found it weighed 2g LESS than the original foam pod.…
Made this to cover my motor which stuck out too far and I didnt like it. I mounted the firewall flat to the front of the fuselage instead of inset like I was supposed too, oops. Not sure how many others may have set it up this way, but…
This is for the right leg, mirror for the left leg. Category: R/C Vehicles
The Latch is made to stick out just a tad more than the part I remixed it from. And I'm pleased to say it does and holds the hatch better! If you download the timber hatch and print it this will fit it just like the one that's supposed…
Replacement parts for the FT Spear. The winglets are slightly smaller than the original ones. I've flown many rounds now with these on and the winglets didn't break yet :-) Category: 3D Printing
Formers and Spars for the Flite Test Corsair Master Series.
Use these hooks to perfectly mount your RC delta wing on the wall. Includes countersunk screw holes for a #10 pan head s
Pushrod Keeper for Turbo Timber Evolution / E-flite Timber – 1mm Pushrod Designed for: 1mm pushrod, suitable for 90° bent pushrods Infill: 100% Layer height: 0.12mm (for best performance) Material: PLA possible, PETG recommended for…
This model is very useful because if you own a Flite test plane you know that most of them use barbecue skewers to hold the power pod to the fuselage, but if you crash or have a “hard landing” you probably know that the skewer will rip…
Thin walled print of the spar for the center portion of the bluntnose versa. The original with 3 layers of foamboard sandwiched together got soft so the wing would flex too much. This is much stronger and only slightly heavier. Print…
Simple wall mount that holds on to the fuselage. use 2x M3 screws.
This is the motor mount for Flitetest FT-22 Raptor, it's designed for 5mm foamboard thickness. Motor spacing can be 16x16mm or 16x19mm so it accommodates most of the quadcopter motors. Printed with orange PET-G for temperature resistance.…
A Gridfinity holder for E-flite's Heli Tool Set, 6 pc
A simple battery protector cap for E-flite 1S batteries. Printed in Overture TPU.
Print two. Use dry wall screws to fasten.
I am going to be traveling soon so I wanted a case that would meet the TSA requirement that all batteries had to be isolate from each other so that the contacts can not touch each other, or other batteries. I designed this case to fit…
Eflite Carbon Z Cub SS 2.1m small parts box provides a nice way to keep the small parts together when traveling or for storage. I press fit magnets to hold the lid on but you could just as easily use rubber bands or a velcro strap to hold…
Replacement horn for Eflite F-18's elevator, you will have to drill holes for screws
Using a spare thick landing gear wire included in my FT Tutor kit I bent an additional strut to support the landing gear. The about 15" wire was cut to about 14" in the process and bent into a trapezoid-like shape. See photos, pretty…
Designed for RC-Plane Night TimberX Evolution. Mounted on the wheels, held in place with rubber rings. No disassemble of wheels needed. I printed in PETG with organic supports.
This is a mock up of the EMax Grand Turbo GT2215 motor used by Flite Test RC airplanes in the C power pack. I made this for display purposes, so a ceiling-hanging model wouldn't be tying up a motor. You could also use it for mocking up…
Clips to allow a Veriflite time of flight sensor to attach to a EuroTramp bed. They don't work well on Nissen beds but Continential beds with the metal anchor bars work fine too.
This is a reinforced version of the standard FT fire wall with plastic walls that go back and increase the strength of the power pod. You can drill out a hole to fit a barbecue skewer to hold the power pod to the fuselage and this…
lite Test Goblin motor mount for increased airflow over the motor. This power pod is for 22xx 2300kV'ish or similar quad motor. This fits snug into the fuselage allowing a good friction fit. I was having issues with the original mount in…
With an “oil cooler” modeled on the smile from Yakko Warner, this is a cowl designed to fit the Flite Test Mini Speedster or Sportster. It is a little wide so you can add a foam core doubler to the nose section of the fuselage. I print…
A great replacement for the cheap and break-on-the-first-flight foam nosecones used on the E-flite UMX P-51 and similar models. Use supports. Just dap a bit of super glue in the middle of it and set it onto the prop. Easy. Please like!…
The latest version of the swappable power pod firewall, works better than the simple flat one. Crash tested.
Print a pair of these (they fit diagonal on an Ender bed) and get some 6mm OD carbon tubes from Amazon. I used the carbon tubes to enlarge the original front hole. The rear is a little farther back than the original location but not by…
Well I don't need them yet but had a little time to make the propguards. Printing separately creates the strongest elements. Print out the PDF of the layout and tape the hoop and the Assembly stand in place. Tact the arms to the hoop…
Dashboard to fit e-flite Extra 260 model. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.25 Infill: 100 Notes: Extruder Temp: 202 Bed Temp: 60 Layer Height 0.1 P/S: 41.7 Retraction on…
Easy mount for adding the DJI FPV system to the Flerken. This version is for the Caddx camera. Holes are added to fit the battery-board in the original Flerken.
Motor/skewer covers for FT Simple scout. May work on other swap-able plans. Duplicate and mirror the STL for 2nd side. Category: R/C Vehicles
FT Super Bee Nacelles. I was tired of having to cut out more foam for power pods after a crash. Using these, I have no issues except for the occasional bent prop. This printed fine without supports. Just remove the integrated support…
Winglets for the FT Spear - Wing tips, with blister for internal LED. Winglets are not interchangeable - there is a left and a right. Blister is, so print two.
I found other 3d printable control horns hard to print, and after seeing flitetests laser cut ones, I realized that they don't need to be fancy. I found the template for this one on the plans for the mighty mini tiny tutor.
I've dummied up a "speed ring" cowl for the FT Goblin (on an "improved airflow" mount I found on Thingiverse. This is a remix of https://www.thingiverse.com/thing:3311705 It has a cool look to it, for sure. I have printed two of these,…
Jugs Lite-Flite Baseball & Softball Pitching Machine Cover replacement. For this pitching machine: https://jugssports.com/products/lite-flite-machine.html?srsltid=AfmBOorgNebSw38lsBRKwc4jdSc-XdDYA6TxcFuULqsSFSM-jFcYENg5 Printed from PETG,…
2 Versions of the Flite Test RC control horns. Print them, hot glue them in to some foam board, and go flying! No supports needed, can be scaled up.
After watching the latest Flitetest VLOG https://youtu.be/-H76d7_7qSs I decided to modify their design so you don't have to saw it in half and hollow it out after printing. First I made it a solid in Meshmixer wich unfortunately softened…
Print with 90% infill.
This model was designed for the Eflite UMX Beast, which means it may or may not fit other micro aircraft of this type. The mount is designed to hang your UMX Beast on the wall.
This is the fin for the E-flite B2 Bomber RC airplane. Print with the slots facing up or print vertical with a brim and supports to build plate only.
Print one as is. Mirror for other. Dry wall screw to fasten to the wall.
Printed in TPU this spinner replaces the stock foam part of the UMX Cirrus for a more durable and better looking spinner. I found TPU made by GIANTARM in their color blue is an exact match for the stock blue color.
