98 modeli
The Ultimate First Layer and Adhesion Calibration I designed this model to test several calibration and adhesion aspects like for example: Nozzle Offset Adhesion Roundness Small-feature performance Also it gives you an indication for…
Wydruk około 0,25 €–0,31 € nettoWstępna wycena jednego wariantu
rectangle 1 layer thick to test your bed adhesion and clear off residue from print bed infill-100% Supports-no Rafts-no
Wydruk około 0,99 €–1,20 € nettoWstępna wycena jednego wariantu
This is a quick test I designed to test bed adhesion. There are some crazy tests out there that'll determine holding power and such, but I just wanted something that would replicate the sorts of issues you might run across in everyday…
A simple test to check the bed adhesion and shrinkage of your filaments. I designed the model so that it should definitely lift from the bed. I wanted to test how much different materials shrink and how the enclosure affects them at…
Super quick and simple print I recommend doing after you first setup a new resin printer. Simply duplicate the raft out to line the build plate like you see in the image, and print it off. I recommend keeping the slice file on your USB so…
This tests the adhesion in a few more spots, to better fine tune the bed levelness
The higher you print it, the heavier it gets! Test your bed adhesion with this. Play with your fan speeds, your heat settings... see what works! The higher it prints, the more it pulls on the bed. Measuring gauge on side in 25mm steps.…
CHANGELOG: 4/2/2020: Updated the model to have more support between bands. This makes it a little harder to pull apart, but ensures that the bands adhere well to each other, as I found that some layers would not adhere and cause stringing…
Simple but effective bed adhesion test for your 3D printer to verify if your bed leveling is correct. The model is shaped to be only one layer tall so you can peel it just right off and not waste material. The xy dimensions are calibrated…
This is a qualitative layer adhesion test. If your trying to get the best layer adhesion in your prints, you can use this model to look at the failure mode of your layers. Ideally, you are looking for a cohesive failure where the part…
I have scoured printables for the different lucky 13 hand gestures that have been made so far. this is primarily a repost to put all of them in one place. I'll continue to update this list as new ones come out. Each file is a pair of…
Pretty simple cylinder. Good test to see how well your prints stick to the bed. Use the 40mm tall one to test various temperature settings and/or other settings until you find the one that sticks nice and firm to the bed after the print…
A 3D-printer torture test. Highlights cooling, overhangs, stringing, bed adhesion and more. Please note that this is not an easy print, ensure proper bed adhesion before attempting this. I wanted a model to use while finding the optimal…
Test your bed adhesion with this fast and simple test. Print with spiralize/vase mode. LH 0.2 30mm/s (or slower depending on your cooling capacity) ~25min print. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports:…
This model is designed for printing with a .4mm nozzle and .2mm layer height. It's a great way to diagnose and calibrate things like nozzle offset and fine details as well as overhangs and retractions. I printed my test on a direct drive…
Let me know how many levels your printer reached !!
Calibration Test Circular – Retraction & First Layer Check 🎯🖨 Not sure if your 3D printer is calibrated correctly? This Calibration Test Circular is here to help! 💡 Test your printer's retraction settings and first-layer accuracy with…
What you see is what you get. :-) Data: Build plate adhesion: Skirt Number of lines: 4 Daten: Druckbetthaftung: Skirt Anzahl der Linien: 4 Print Settings Rafts: No Supports: Doesn't Matter Resolution: 0,2 Infill: - Filament: all Category:…
I've used this part to test ZillaGrip on my steel FlexPlate. More info in my video: youtu.be/IrL0kZ1LjYo It's a copy of Toms design used in his video about Grocery Store Bed Adhesives:d youtube.com/watch?v=MAw2FK8y5i4 Print Settings:…
Please give it a ❤️ if you like it 🥰 I designed this model to compare the adhesion of different 3d printer beds. Video FR about it: Please give it a ❤️ if you like it 🥰
I created this model as quick test that is larger/more in depth than the included bed leveling test in Prusa firmware but still smaller/quicker than most tests out there.
Print in any layer height that will print only 1 layer (the model is 0.2 mm tall).
after 8h of printing i saw that 2 parts havent enough Adhesion, so i added a hardcoded brim like in the orgiginal files from Popandsicle
Had some problems with some filaments not sticking to bed, so I made few benchmark shapes and sliced them in 5*C intervals between 180-230*C Some times the temperatures given in box are not the best ones ;) Files are sliced for Prusa…
Simple and effective warping/bed adhesion test.
Printable sheet to test the adhesion of your 3D printer bed sheet throughout it's entire area. Multiple files provided for the following print area sizes: 200x200mm 220x220mm 220x300mm 230x270mm 235x235mm 250x250mm 255x255mm 300x300mm…
Test your bridging/cooling settings! Check if your bed adhesion is good enough for small footprint parts. Prints in minutes and uses less than 1 gram of filament. Category: 3D Printing Tests
Size up or down to your liking, however sizing up will help with adhesion.
Simply a Layer Adhesion Test
This little benchmark print helps you to figure out how well sharp corners stick to your printbed. Both the inside and outside corner are filleted with a different radii. The size of each radius can be seen on the adjacent face. Overall,…
Hey! I've been having some adhesion and levelling issues with my print bed and so I created this that shows me where on the print bed I have issues. A bit of trial and error, change settings in those locations and I was back to printing…
Remix of the Prusa Face shield and 3-hole variant. This adds a 0.6mm pad at the end of the headband to help with adhesion. Three hole original: https://www.prusaprinters.org/prints/26610-face-shield-3-holes RC2 original:…
This is the world almost famous adhesion test. As seen on REDDIT, in r/3Dprinting.
Easy to print Test print for bed adhesion This is a good test print to check your bedplate. Settings: 0.1 - 0.2 quality 100% infill PLA No supports Njoy
This project started as a simple desire for a versatile vase test for my 3D printers. In collaboration with Gemini AI, I generated OpenSCAD code to create a unique twisted square vase. The design comes in two variations: Normal Vase: A…
If you like my design you can support me on BuyMeACoffee - https://www.buymeacoffee.com/kaushikbm -------- Many a times while printing small objects we face difficulty in making them stick to the bed and keep it there. These anchors are…
FINALLY! I can print more than 2 or 3 of these clips without an adhesion fail. I print these bag clips when I want to finish rolls of filament, then I give them away to friends, family, or anyone who shows interest in my 3D printers.…
Tired of using boring and easy to print calibration cubes? Now you can use a brand new B.A.T.C.H. ( B ed A dhesion T est and C alibration H exagonal-polyhedron) You will test your bed adhesion with a small area of 66.725mm^2…
Benchmark model should be placed as it is and it should printed in vase mode or with high percentage of infill for higher difficulty. The base circle has diameter 20mm and it expands to 50mm. Model is 180mm tall with 10mm safety borders…
An abstract sculpture of a tree-like shape suggesting the cohesiveness of material and ideas - the notion that everthing fits into an all encopassing whole. Category: Sculptures
I wanted to test adhesion properties of various materials on different sprint steel sheets, and I needed a model to do that. Thus I designed a star with narrow “arms” that also has a hole, so you can hang it somewhere as a decoration once…
overhaulin the connection for better stability
Bed adhesion torture test. Tests the bed adhesion in all four corners of the bed and can be scaled to fit different print beds.
These 0.2mm high, 2D sine waves based on https://www.thingiverse.com/thing:11243 are for testing bed leveling and adhesion. Since the printhead is always changing direction during the sinusoidal motion, poor adhesion will show up quickly…
A simple print to test the adhesion strength of glue on different kinds of filament. Print two of the testers in the filament you want to test. Put some glue on the bottom of the testers and stick them together. After the glue is dry, see…
I noticed, that the inbuilt brimears in some slicers are far too weak. So I designed some more durable, which can be merged with the model. Included are versions with 0,4 and 0,6 mm height. I recommend the lower one, it is strong enough…
A fairly brutal adhesion and overhang test designed for the new super tack build plates.
When I build prototypes using FDM, I sometimes experience delamination and breakage of my 3D-printed parts. It is not always possible to rotate the part to optimize strength, which can lead to adhesion and delamination issues. I have…
I've had many failed prints due to a single part coming off during a large multi-part print. It's taken me too long to realize that there is a very simple solution to many of these bed adhesion problems if you just add these helper discs…
Wall thickness test designed for 0.4mm Nozzles This model is specifically optimized for 0.4mm nozzles, ensuring accurate and reliable results. The wall thickness progression is based on the typical extrusion width of a 0.4mm nozzle, which…
easy 1 layer adhesion test fo the creality k2 pro. The dimensions should be a little bit smaller than the plate.
Simple lint to test bed adhesion.
Description This Hip Replacement Stem Test Print is more than just a calibration tool—it’s a functional test of your printer’s limits and a nod to cutting-edge orthopedic design. With a unique geometry inspired by advanced hip replacement…
quick adhesion layer test for the ender 3 v2 or other printers with a print bed with 125x125mm bed. its very useful, so i wanted to share.
Remix of InstantBenHur. Many thanks for the awesome design & providing the .step file. After I already printed three of the original models I noticed some possible improvements so I changed it to be Easier to stack (1cm taller) Faster and…
This is a holder for Bed Adhesion sticks. It is sized for a Magigoo 50ml stick but will fit a Kores or Elmers stick as well. Sticks are angled at 45 degrees so the rack can be mounted to the wall easily with command strips. Attribution:…
This is a test I used to fine-tune my ASA printing, squish and flow rate Print Settings Printer: Voron 2.4 Rafts: No Supports: No Resolution: - Infill: Filament: - - Category: 3D Printing Tests
I designed this in tinkercad. Print without supports to see if your printer is dialed in with bed leveling
This test print evaluates your 3D printer's bed adhesion. If the hinge falls out of the glasses when you remove them from the build plate, your printer has failed the test. To address this, either clean your build plate thoroughly or…
To execute the test, you need to insert the Test_OBJ in the Adhesion_Testframe. Then you hold/stand on the frame and bull on the Test_OBJ until it breaks. I use a bow scale which saves the maximum force after the part breaks: szdc88…
the bed adhesion test is to test bed adhesion make
Don't know how good your adhesion is to your bed of your printer. use this to figure out your settings to make a better bed adhesion to your 3d printer without using brim. enjoy and let me know how high you were able to get. can be cut to…
In the photos, you can see a print made with ASA filament at a bed temperature of 100 °C and 110 °C.
simple print bed tab designed to improve adhesion for prints with sharp corners and reduce warping during printing. These tabs can be added in your slicer to help anchor models to the build plate, especially for parts with small contact…
This is a model that you can print to test your printers bed adhesion to the limits. It includes a vertical and a slanted version. As well as a short and tall version. Feel free to tweak the settings as much as you want. Happy testing! :)
Simple calibration card to test your filament flow and adhesion. STOP LOSING MONEY ON FAILED PRINTS: I use this card to test new filament rolls before committing to big prints. I realized I was losing 15% of my filament on tests and…
ACPS First Layer Adhesion Test Model 220x180mm 0.1/0.15/0.2/0.3mm layer heights
this torture test is torture for your printer.
This is still a work in progress! I haven't gotten a chance to actually cut this (waiting on parts/time) yet. Putting it out there anyway. This is a Control Panel for the K40 Mini (the 30w, smaller version) that incorporates a…
Every time someone figures out whether a filament sticks to a plate, that answer stays in their head, and the next person burns time and filament rediscovering it. You end up getting people in discord or reddit or forums having their own…
Tired of dealing with scattered dust and cleaning up after drilling some holes at home? Have a look at my dust collector/catcher designed for self-adhesion and effective dust capture. It works with most vacuum cleaners, making your…
This model just prints two discs in all possible combinations of the 5T Prusa XL. I had problems with the adhesion of some PLA+ / PLA pro / PLA plus filament combinations of different providers. Also this will help detect whether your…
I made this model to test my adhesion of small surface areas. Extremely hard (for me at least) to get to work. See how high you can go and share your settings. I have completed it myself after a fiddling a bit. Maybe I'm a noob, show me…
Funny little mould for pressing sand, makes the text "THIS LAYER ADHESION SUCKS" in the sand.
A simple adhesion and warping test that is parametric in OpenSCAD. Place “mainpart.stl” and “adhesion-warp-test.scad” in the same folder. Set the base_length (the length of the block that is printed on the bed) and the level (the highest…
When I routed my Network Cable through our apartment I simply forgot putting something over the drill holes BEFORE putting the cable through. Therefore I had to devise a model that allows me to run the cable through while holding firm…
this model is meant to test bed adhesion and overhangs.
Just a few simple cylinders to help keep finicky corners down on the build plate if they're misbehaving. Some slicers (like PrusaSlicer) have this function built in, so you should use the native functionality instead. Usage Import your…
This is an upgraded base for the Xiaomi Mijia Night Light 2 that replaces the original magnetic cover and offers a much larger adhesive footprint for reliable mounting on textured or uneven surfaces. Now available in three variants so you…
A simple remake of Mercury one Frontplate. The fine grill replaced with a broader cross. I made it because i had problems with printing the very fine mesh on my glass bed.
The original caps on 3DLAC Adhesion Spray easily cracks. They are also made with PP and cannot be glued back using regular super glue. Here is a handy replacement. Modelled in Autodesk Fusion 360 and fits perfectly!
Supports are recommended, ender 3 completed multiple prints without supports and quality was fine one side for light, other side for tape or magnets 1mm inside
if you have any other questions feel free to message me through printables I used the orca slicing software with the marlin generic gcode If you likethe file consider following my page I will be designing more accessories for the printer…
A fun (or maybe not so fun) way to discover the truth about your 3D printer's adhesive abilities. Not long from now, I will post a picture here of what my 3D printer (AnkerMake M5C) comes up with. If you print this, then please leave a…
The purpose of this test piece was to assess flexible‑filament adhesion on PETG and to review the ring’s deformation properties when printed with Colorfabb Varioshore at maximum foaming. I have included the 3MF file as a starting point…
After receiving a new printbed, the adhesion seemed much stronger than I remember, I 'designed' this model to help show off as less of a test and more of a demonstration of abilities for strong adhesion. I printed these without issue on…
The Shrimp Spermatophore Adhesion Apparatus is used for testing the adhesion or stickiness of spermatophores. As seen in the figure, the glass plate configuration is slid into the holder and the force gauge is hooked onto the other side.…
This technical model is designed for a two-stage validation process in the maker workflow. It allows users to calibrate both the mechanical bond to the 3D printer's build plate and the chemical bond of post-process coatings Stage 1: Bed…
In the 11th Edition of Warhammer 40K, squads all need to stay within a 9" limit to remain coherent. Not a problem for small squads, but if you're playing a horde army it's nice to have a quick way of checking. Print all three arcs. Number…
To execute the test, you need to insert the Test_OBJ in the Adhesion_Testframe. Then you hold/stand on the frame and bull on the Test_OBJ until it breaks. I use a bow scale which saves the maximum force after the part breaks: szdc88…
After receiving a new printbed, the adhesion seemed much stronger than I remember, I 'designed' this model to help show off as less of a test and more of a demonstration of abilities for strong adhesion. I printed these without issue on…
The original caps on 3DLAC Adhesion Spray easily cracks. They are also made with PP and cannot be glued back using regular super glue. Here is a handy replacement. Modelled in Autodesk Fusion 360 and fits perfectly!
quick adhesion layer test for the ender 3 v2 or other printers with a print bed with 125x125mm bed. its very useful, so i wanted to share.
easy 1 layer adhesion test fo the creality k2 pro. The dimensions should be a little bit smaller than the plate.
This model just prints two discs in all possible combinations of the 5T Prusa XL. I had problems with the adhesion of some PLA+ / PLA pro / PLA plus filament combinations of different providers. Also this will help detect whether your…
Wall thickness test designed for 0.4mm Nozzles This model is specifically optimized for 0.4mm nozzles, ensuring accurate and reliable results. The wall thickness progression is based on the typical extrusion width of a 0.4mm nozzle, which…
![[Adhesion Fix Remix] Cam lock bag clip](https://media.printables.com/media/prints/0e68c640-31dc-4903-aa81-c039838a7716/images/9799190_0508c4ff-d768-4110-88d8-562f610ca2ef_2d139680-28fa-430c-beaa-4cc2ff118352/20240225_180635.jpg)
