Liczymy pasujące modele…
Replacement knob for KORG nanoKONTROL2 Print instructions I recommend to print it in PETG with elephant foot compensation on. Infill 100% prints in about 15 minutes. No supports are needed but you might have to clean up the ceiling inside…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Its logo from game Portal2 Btw im out of gas in torch so i know i need to clean it up :D
Wydruk około 5,46 €–6,67 € nettoWstępna wycena jednego wariantu
The original design from https://www.printables.com/@MSTVS printed fine and fitted perfect. However the end was too sharp for my taste, becoming a problem when I stored the iPad with the pencil on it in a bag. So i reengineered the…
Wydruk około 0,20 €–0,24 € nettoWstępna wycena dla PETGMateriał u źródła: PET
I have a weber "Master Touch" Grill and a iGrill2 thermometer. The problem is where to place the thermometer during grilling. It has a magnetic base, but you cannot stuck it to the kettle, it is too hot. So I designed and printed a small…
Wydruk około 2,80 €–3,42 € nettoWstępna wycena dla PETGMateriał u źródła: PET
(The links below are affiliate links. I may earn a commission at no extra cost to you, helping keep my work free and continuously improving my designs.) This case is meant for this Electronic Load:…
This is my model of a Sterling SMG MK4 (L2A3). Not only was it a real world weapon, but it served as the basis for the E11 blaster carried by stormtroopers in Star Wars. All parts were modeled to measurements taken from an actual Sterling…
This is a mount so I could easily fit a Cardo Spirit HD intercom to my Shoei GT Air II motorcycle helmet using the SRL2 standard fitting system. Shoei helmets are built to take their own intercom system but it's very expensive and I…
One of the triggers was broken on my PS4 controller, and I decided to 3D model some new ones instead of replacing them with generic replacements. These are flat replacement L2 and R2 buttons for the first gen PS4 controller (CUH-ZCT1).…
Model of L298N DC Motor Drive Controller Board Dual H Bridge
This project takes an Atorch DL24 Electronic Load module and makes some minor modifications to it and encloses it into a custom 3D printed enclosure to provide improved handling and board protection. The project also converts the DL24…
You can scale to suit but at 100% it just works and doesn't use that much filament. 0.15mm layer height using a brim. If you print multiple on 1 bed, make sure your retraction settings are dialed in as it will create multiple artifacts.
Atorch DL24 150W Electronic Load Case For the newer version that can be powered by a 5V USB-C power supply . The top cover can be installed without having to disassemble the heatsink with fan and re-paste the transistor - The top cover…
Accurate S&T Sterling L2A1 AEG replica Accurate 1943 M38 scope replica Accurate small eagle Hengstler replica Accurate SDS power cylinders replica Accurate Element Airsoft M300A Mini Scout Light replica Functional features include: Moving…
I own a SHOEI GT AIR II motorcycle helmet ( I love this helmet ), and was frustrated with not being able to easily mount other communication devices due to the SRL2 mounting points take up room on the helmet rim. I decided to see if I…
A holder for the WAGO221 with labels L1, L2, L3, N, and PE. The holder mounts with M5 screws. An additional model of the holder is available without labels. The Wago fits snugly, requiring a slight pry to remove. I printed at a 0.16mm…
Protective, low-profile snap-fit case for the L298N Dual H-Bridge Motor Driver Controller Board . Both the top and base have port and pin header cutouts with an exposed heat sink. The base comes with dual side mounts and a central bottom…
I bought an Atorch DL24 to do some load testing on the mess of USB cables I have. I think it will also come in handy for other projects. It's a pretty nice piece of equipment, but I'd much prefer to keep my mitts off the PCBA. So this…
Wall mount for Makita DCL286/CL003. STL file is already set for best orientation. Use a tiny bit of support for the first few layers. Use 0.2mm layers on a 0.6mm nozzle, or 0.15 on a 0.4mm nozzle.
L298N Case with Zip-Tie closure and Screw holes for placement Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament: Generic PLA Wood Category: Electronics
"It's... the Borealis ?" "Good god." "What? The Borealis? It's real?" Well it sure is now. More exactly the version seen in Half Life 2 Episode 2, which is heavily based on the USCGC Healy icebreaker instead of the Polar-class ones. I…
This is the housing for DL2MAN uSDX Sandwich , so users that already have an existing Sandwich can print an easy housing. It requires to remove the electrolytic capacitor below OLED, replace it with a small tantalum capacitor and solder…
I printed these in “draft” mode, 0.2mm layer height, and 20% infill, on an Anycubic Vyper with support. Print the nut and bolt from the Xbox One version, as it does not need to be modified. The paddles were modified from the Xbox One…
Materials 4x M3x3 heat set inserts (short) 4x M3x10 socket head screws Print the LED light guide with transparent PETG. You can find a nice guide here: https://www.printables.com/model/15310-how-to-print-glass Preparation Put M3 heat set…
I took The Hornby OO scale Santa's Express Christmas Train Set (R1248) which is meant to go around the bottom a Christmas tree and built a platform for it to go around the middle of the tree above the reach of toddlers. Brief and not so…
These clips are ment for the Ortlieb panniers with the QL1 / QL2 klick system. https://www.ortlieb.com/de_en/ql1-ql2-hook-inserts The originale ones come in the sizes 8mm and 11mm to fit the Bike rack. These here are designed for Bike…
You can take all the rest of the housing components from the original design.
Complete case for the Atorch DL24 battery tester. Unlike other cases I found, this covers the heatsink and fan. This may not work with some larger fans out there, so your mileage may vary. I'm personally using it with an 80mm Noctua fan…
Any one who was born in the early 80's rember the day when SONY released is first Walkman : the TPS L2 . Easily recognizable with its blue and orange colors, this cassette reader was as revolutionary as the first iPhone was in 2003. This…
Remix of @Wiseone's DL24 case Switched to socket head screws. Cutout for speaker added Added nonbattery powered version
Backpack details for the Titanfall 2 Viper costume
A case for the Atorch DL24 with external display (DL24M). Support my work For non-Prusa parts and filaments, check out 3DJake ( International , UK , Germany , France ). I'll get a small cut of any order you fulfil using these links (at no…
Official 3D print files for the CL2.
If you are printing and building my Sterling or ANH E-11 model found here: https://www.printables.com/model/162480-sterling-smg-mk4-l2a3-and-anh-e-11-conversion But you want a version that can take some rough handling, then this is the…
Materials 4x M3x3 heat set inserts (short) 4x M3x10 or M3x12 socket head screws Optional : Print LED light pipe in transparent PETG (or skip altogether) Preparation Insert M3 heat set inserts, being careful of posts with cut profiles…
These unobtrusive LED bars shine light at the print from both sides, for great visibility even on the first layer. This version uses a switch. Design features: This design adds a switch to my previous design:…
The crevice tool of the original 3in1 nozzle of my vacuum was to short and to wide to get into any crevice, so i made a new one. The openings inner diameter is 35mm, decreasing to 34mm along the way to ensure a good fit. The flattened…
Updated: MMU version so you can print the Voron logo in-place. Follow this guide to calibrate your printer to do it Updated: Faceplate now can support both 3010 and 4010. Put heated inserts in the correct location depending on what fan…
Sonoff ZBMINIL2 DIN Rail Mount Print Terminal Mounts and snap piece from the original design from Harry .
This is a case for the generic L298N module. It has a slide on top, and openings to reach the terminals. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: No Resolution: 300 Microns Infill: Doesn't matter Notes:…
Phone-animated portal for tabletop RPGs and six different portal's animations !!! Printing large parts requires a printer with sufficient working area. The size of the working area of the 3D printer is larger than 130x80x165 mm. But it is…
A Mitsubishi L200 2009 model car that you can print along with the tires. The tires were one of my ideas to add to this model car where it can rotate, and front wheels will be able to swivel that linked to the other side. Use filament,…
The purchasable version is overpriced and also from 3D printing. So I have drawn my better variant. Just use the sheet metal and the original screws, they fit perfectly! Printed from PETG. Category: Office
Resized for MINI L2 module
Printed with PET-G filament.
This is a model of Mitsubishi L200 2009 pickup truck model that I modeled to be 3d printed. Sorry there are no tires modeled for this particular 3d file, the client ghosted me after its completion, hence I somewhat abandoned this. If I…
Modification: Fixing the device to the board Led diffuser for BT LED version
First of all, thanks to everyone from Armchair Engineering and to tktktktk VT.1020 from Voron Discord for designing the duct. It is my iteration of the Xol2 Rapido HF + CPAP. The design has been tested and works pretty well. Please let me…
The standard hooks only work for very small bike racks with thin tubes. a lot of ebikes have thicker ones. Aparrently you cannot buy them in other sizes. So I made a model. The small one can also be used to replace the original, even if…
The following PDF contains custom settings that work better than the default profile included with the Flashforge Creator 5 and Creator 5 Pro. Most of these settings will also work with the Flashforge AD5X and possibly other printers such…
Model : This model fits the Cinelog25 v2. It is used to mount the DJI o4 Air Unit Pro. It is compatible with ND-Lenses. Print Instructions : Material: TPU, I used the Eryone TPU Filament Placement: Place the model on the bottom, just as…
Design based from the original parts. works with standard resin. It might be printed with an 0.2 or 0.1 nozzle for FDM printer as well. After 6 months of daily use one part broke. I made a V2 of the hook a bit thicker at the base and add…
Scout mech from the game HAWKEN with movable parts. Individual printable parts in the zip. I printed my make at 30%. Print with supports from base adviced.
Printed from Devil Design ASA
An enclosure for the DL24M electronic load. Powered with a 12V Barrel or 12V USB C PD Port. To mount the board in to the enclosure you have to remove the green screw terminal housing or edit the cad file. All screws are mounted with brass…
Model of Chainsaw Homelite XL2 in scale 1/10 With this scale is intended for SLA printers.
The process of installing this is easier than you'd think , I'd personally follow the IFixIt guide for disassembly and reassembly ( Up to Step 10 , Step 11 & 12 are unnecessary for this). I would heavily recommend printing this with a…
Dock to house the Nanokontrol2. I used this with MidiMixer and the WaveLink plugin to control the Wavelink sofrtware from Elgato. I've modified the model slightly since I printed it but not tested it due to having a new setup now.…
Have developed further on a damn good idea. Change it so there is more room to remove the purge filament.
20mm deep electrical box extension adapter. Application: 20mm thick wall panels with 68mm hole
Ein einfacher Snap-In Halter für den MAKITA Staubsauger DCL281. Er funktioniert mit oder ohne Akku. Benötigte Schrauben: max. 5 mm, Länge nach Bedarf Material: PLA Auflösung: 0.2 mm kein Support Infill: Cubic, 50% 4 Walls, 4 Oberflächen…
Printed parts should be uploaded in the correct orientation to print. Check images for fan duct orientation, assembly and built in support locations. Be careful what fans you buy. The gdstime 4010s work flawlessly but the fabreeko hb…
Anschlagwinkel 200mm. Anschlagplatte wird mittels Ruthex Gewindeeinsätze M3 und Zylinderschraube M3x8 befestigt
Screwable caps for UHF type connectors according to 5/8 - 24 UNEF
A case for the Atorch DL24 with external display (DL24M). Encoder connection and button see link: https://vae-tech.forumactif.org/t254-dl24m-charge-active-testeur-de-batterie#2266
Atorch DL24 Electronic Upgrated Top The original top cover didn't fit my DL24. The incompatible parts were the buzzer, the Type-C port on the top, and the charging port. I redesigned the cover for the updated DL24 and updated the top…
I just created case for battery box, which fits existing case for electronic load - Atorch DL24 - https://www.printables.com/cs/model/405292-atorch-dl24-electronic-load-case. I could not find anything already existing so it can be…
This is intended for holding an Arduino UNO with an L298 motor shield on top of it. The cover is a snap fit with access to the L298 connection screws. This was printed at .2mm layer in PLA.
Found the labyrinth maze to easy so made a harder lvl2 maze. I've kept the body and legs the same download here https://www.printables.com/model/593407-star-wars-r2-d2-r2d2-puzzle-with-windup-leg/files and simply reprint the head, no…
A simple L298N riser, it raises the motor controller 5mm above the floor, it helps protect the controller from scratches. Dimensions (mm): 43 x 43 x 5 Average print time with 0.4mm nozzle 70 mm/s print speed 0.2 layer height = 25 minutes…
I wanted to store the Atorch DL24 Electronic Load module plus the accessory that I ordered with it away till needed, I did have everything saved in a container but still, it was not what I wanted, so I searched for something that will…
This is the pinnacle of my tire designs for the robotmover. This tire wont get stuck, rip up your edges or clog up with dirt. Tire is 20mm wide, but use the slicer to extend to 40mm. Printed on CR10s PRO with microswiss directdrive. Rim…
I made an adapter to use a L24Q monitor on a VESA mount. reuses hardware that came with the monitor. I used PETG. Would not recommend using PLA. Print with 2+ perimeters and decent infill.
OK, let me acknowledge, first of all, that I know the Rogue One E-11 was built on an airsoft replica of a Sterling and not a Sterling itself. However, at the time I made this model, I did not have the airsoft replica for reference at the…
Another Reel to Reel Nab adapter Its prototype. Tested with Tascam and Akai Reel to Reel. White powder that is a bit visible on the red Nabs is a solid toilet soap. Helps move threads ... For better tolerance, I personally print the lower…
Shift knob is from a 2002 MAN L2000 PhoeniX Campingcar with a 6 shift Eaton-Gear. Label is lasered on 1,5mm signmaterial on a Mr. Beam Lasercutter. Final Knob is finished with filler and glossy black spraypaint. Very special sparepart -…
Variace na Atorch DL24 - úprava krabičky pro verzi CL24R 150W
Prevent the automower from digging ruts in your lawn. Printable on a 220mm square bed. This is a remix of a excelent design by polandmet so that it would print on my 220X220mm bed. https://youtu.be/YmMLucwmtG8 Each wheel prints in 4 parts…
Battery Cap with nice friction fit for Nikon EN-EL25 Battery (for Z 50/ Z fc)
Another remix of Pfelpensson's GAZ66. This time an electronic intelligent system for searching and positioning of enemy radio signals in the range of 500…9000MHz and a depth of up to 70km. Two version of the vehicle can be printed – on…
19/08/24- Added reinforced variants for both normal and flat trigger, due to an issue with the normal trigger breaking with heavy use. Flat trigger should be fine. Two triggers inspired from the Radian Weapons Vertex, for the sbl2. Print…
An ORP-Compatible holder for an L298N Motor Controller. About ORP ORP (Open Robotic Platform) is an open-source project for developing reusable and user-friendly components for use in hobbyist robotics. By following a set a design rules,…
Recommend Printing in PETG or something with good heat tolerance considering the heatsink. Can be incorporated into existing 3D models, screwed, or glued in place. Optional mounting caps included in model.
A wrench that you can use for your Hayward CL200 Series Chlorinator, make it's much easier to remove the cap. I printed this with PLA on a printer with a 300mm x 300mm bed. I had to rotate the print 45 degrees to get it to fit the bed. I…
Version two - much better fit and a bit stronger. Print with the angled side downwards and a small layer height. Use 0.2mm layers on a 0.6mm nozzle, or 0.15 on a 0.4mm nozzle.
Cartographer/Beacon Probe Mount for Rapido UHF for Voron CNC/CL Tap, XOL2 Toolhead
Usar las instrucciones de la versión original de mi remix.
If you are printing and building my S&T Sterling L2A1 or Rogue One E-11 model found here: https://www.printables.com/model/155855-st-sterling-l2a1-aeg-and-rogue-one-e-11-conversion But you want a version that can take some rough handling,…
A dust cap for a PL259 UHF plug Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Filament: Enotepad TPU Red Notes: The outer barrel of different PL259 plugs might vary slightly…
Sizing edit of @Draco_295340 's deburring tool case. Includes an inset debossed label. Recommended to print in PETG. Example photos are in PLA, debossed label filled in with sharpie (lol). If you do print in PLA, make sure to snap fit the…
0.15-0.2 to print those threads. Use them to protect outdoor equipment from dew - ie, cable extensions
Print at .2mm layer height. Use small supports for the bottom part. Use knife to remove them if necessary - otherwise the snap thingy wont work.
A box I designed for L23UGSR-5HaxD2HaxD Routerboard. Has 1 open side for air ventilation. Uses M3 bolt to hold the board (M3x6-M3x14) will work. Has mounting points on the backside, which use M4 screws with max ~7mm diameter of the head.…
This mount has a minimum footprint, best suited for gluing down. Use four M3x4mm screws to hold the L298N board in place.
This model used to cover L298N red type module.
Adaptall2-Nikon-F camera adapter
for Creality Ender 3/pro
This is a rifle designed to fit gunpla models. Comes in 3 parts, barrel, main body and magazine. Designed for resin printer, may not work on FDM Category: Model Robots
Here are several designs for the USB to UART boards I had lying around. They are pretty quick to print using 0.2 layer, and can be closed with a bit of glue. There are also convenient slots to see the PCB pinout silk screen. Category:…
![Deburring Tool Case (AFA Tooling B01L2XR4P2) [Remix]](https://media.printables.com/media/prints/656236/images/5172135_127ee4eb-1af2-4614-827d-127d6f3cacaf_be530f00-3209-4ede-aa54-90d49423e53a/img_2219.jpg)
