Liczymy pasujące modele…
This inexpensive 3D printed smartphone stand will allow for a smartphone to be held up while it is being used as a magnifier. This phone stand may be beneficial to someone with visual impairment or someone with limited finger dexterity as…
This is a cup riser stand the De'Longhi Magnifica S espresso machine I made as our usual are small and sited a bit too low for our liking even with the “machine's nozzles” set to the lowest position. This is a 20 mm riser with 5 mm post…
I own a DeLonghi Magnifica Evo and let's be honnest, if the coffe is delighting, the coffee bean container is so small you can't put more than 250 or 300g. And you always have to manage half a packet beside the machine, because you just…
This coffe bean reservoir extender allows you to tiple the amount of coffe beans stored direct in your machine to not run out of coffee beans so fast. It ist designes to fit the original lid and use the grinded openig as well. This…
We had problems with coffee grounds molding in the container of our coffee machine. There are other sieves out there, but they are all too loose or/and the grid is too wide, allowing coffee to fall through and also mold. If you're facing…
I got sick of running out of coffee beans all the time, so I created an extension for the coffee bean container. As I am switching from Fusion 360 to Shapr3D, I thought this is a nice experiment in modelling with it. Of course, I did not…
The bean tray of the DeLonghi Magnifica S is small. WARNING: Some people are reporting problems, I printed this without issues but some people seems to experience fitting problems. Take a look at the comments see for yourself. If you…
Grinded coffee measuring spoon for Delonghi Magnifica s. As I lost the original spoon, I've borrowed an original one. And made a new model, but without needing support. I've printed one with 100% infill.
Descaling Container for DeLonghi Magnifica Evo Enhance the maintenance of your DeLonghi Magnifica Evo coffee machine with this specially designed descaling container. This 3D model offers a perfect fit and easy handling thanks to its…
Grid to place into the DeLonghi Magnifica S container to avoid mold.
This is the ground coffee scoop which comes with the Delonghi Bean To Cup coffee machine. I have measured my spoon from a Magnifica ESAM4200 - this might be the same as used in other delonghi models. Print instructions Category: Kitchen &…
ENGLISH : remix of coffee tank extension for DeLonghi Magnifica S https://www.thingiverse.com/thing:6620804 to add the holder of the ground coffee scoop. FRANCAIS : remix de l'extension de réservoir pour Delonghi Magnifica S…
I was looking for a drip tray to descale my De'Longhi Magnifica S coffee machine and found this version, which I liked because of its design. I simply removed the feet (otherwise there would have been too much plastic waste to create…
I designed a good fitting water tray for rinsing and cleaning for DeLonghi Magnifica S. Approx 2.7 L capacity.
Design is heavily based on this model by @HuMa_1372637 , so props to them! Remade their model from scratch to give a little reinforcement to the print as it looked a little weak to me. Install at the bottom of your coffee grounds…
Same point as the original, this is remixed from ( DeLonghi espresso machine pre-ground coffee funnel cap by Petclaud - Thingiverse ) . Useful if machine is used in a shared area by people that may mistake the grounds funnel as the bean…
A nice looking cup tray protection, to prevent scratches for the metal cap tray. You can choose between the clean one, the embossed single color and embossed dual color edition. Happy printing :) How To Print Dual Color (Orcaslicer /…
This is a remix from Lyrylin's "Coffee tank extension" on Cults3d https://cults3d.com/en/3d-model/home/bean-tray-extend-for-magnifica-s and the newer version on Thingiverse https://www.thingiverse.com/thing:4941157 I used the SolidWorks…
DeLonghi Magnifica S XL Beans Container, It fits a whole 1kg bag of coffee Beans, with 2 Windows
The original model is great, but my colleagues and I go through a lot of coffee. So I modified the original model to make it taller, and now the coffee machine can hold approximately one kilogram of coffee. Thanks to the author for the…
This is a protection for stainless steel surface Magnifica
Gasket for Delonghi magnifica S exhaust ——— Joint d’étanchéité pour la machine à café Delonghi magnifica S Afin de résoudre le problème mentionné ici:…
Updated Design: May 2026, improved rigidity Tray insert reduces build up on the bottom of the puck holder, caused by wet pucks. Bacteria and mold growth are reduced, by keeping pucks elevated out of moisture. This also eliminates caked on…
Magnification Throw Lever for Arken EP-5 Scope. This fits any scope with a 47mm mag wheel. Hardware Required. 3mm x .5 x 7mm socket head screw. Printer: MK4S, Filament: Black Prusa.
Da mir das vorhandene Volumen des Bohnenbehälters zu gering war, habe ich nach einer Lösung gesucht, wo der Bohnenbehälter auch stramm in der Maschine sitzt. Ich habe die Maße speziell an meine Maschine angepasst, da es scheinbar…
Container for descale DeLonghi MagnificaS ( 2 litre +)
Supports: No Layers: 0.2 Infill: Grid 20% Filament material: PLA - PETG nstructions: Turn off top and bottom padding 0 layers Perimeters 6
I designed a perfectly fitting water tray for rinsing and cleaning. I 3D scanned the machine and reverse-engineered it to ensure a precise fit for DeLonghi Magnifica Evo. Approx 1.6 L capacity.
This design combines two 4x microscope lenses together to create a stereoscopic 3D macro lens, with 2x magnification and a 5mm stereo baseline. It has been designed to be shot handheld in the field using a flash for lighting, rather than…
Replacement for De'Longhi Magnifica S (ECAM 23.210.B). The tab that activates the sensor sometimes breaks and because of that problem I decided to reverse engineer this part.
Make descaling your automatic coffee machine easier with this simple model! Normally, you need to find just the right container to fit under the outlets and empty it multiple times during descaling. With this model, you can collect the…
A tray to easily descale the Delonghi Magnifica S ECAM 21.117.B coffee maker Snap in place, attach a silicone hose witha inner diameter of 12mm and run it to the sink or to a bucket on the floor, then start the descale program without…
I've been looking for a cleaning container for my coffee machine for a long time, but haven't found one specifically for my model, so I made my own. Material : PLA, PETG Infil : 25-30% Perimeters : 3 Layer Height: 0.24
Hello, This is a plate to replace the original plate in poor stainless steel (scratch and rust quickly). I've made two versions, one part and two parts to assemble for little 3d printer (minus than 230cm size). My first print test fit…
LatteCrema preparation tool holder. print instructions: nozzle 0.6 mm layer height 0.4mm infill 20% walls 3
I made the knob extend out equal length, this way there was less directional torque on the knob and more rotational torque, in an attempt to prevent breaking again. Printed upright with supports, this way the surface of the knob is the…
Cleaning the milk frother adapter is not so easy, so I wanted to have replacements. Use a material which can resist the heat of the water vapor! Especially for the inner part! My first prints were using PLA which is not suitable! Print…
If you ever used the powder option on your coffeemaker you know its quite easy to sill powder all over the top of your bean reservoir. I designed this funnel to be printed in vasemode. If you are using the beans reservoir extension…
Put silicone on the flanges of the big square lid, press it down on the coffee machine and put something heavy on each corner while it's drying. Various heighs are included. The version on the photo is the lowest. Fusion 360 source is…
Arken EPL-4 Scope Magnification Wheel. Hardware required: M3 x 5 Socket Head Screw
A 3D-printed alternative to the original metal part, which always scratches quickly and looks unsightly. It simply replaces the original part and doesn't require any adjustment. I've uploaded two possible file versions for the color…
Adapts perfectly to the top metal platform. ⚠ Sugar dispenser must be printed in 150% scale ⚠.
For the DeLonghi Magnifica coffee maker. Extended bean container. The lid doubles as bin for waste water when cleaning.
prodloužení nohy ke kávovaru Espresso De'Longhi Magnifica S Ecam 22.112 B, lze nasadit na gumovou nožku zespodu kávovaru.
ENGLISH : Grinding adjustment dial for Delonghi Magnifica S Smart for tank extension : https://www.thingiverse.com/thing:6620804 https://www.thingiverse.com/thing:6637869 FRANCAIS : Molette de réglage du moulin à café pour Delonghi…
Purpose: While turning on or turning off the coffee maker, it is cleaning itself and some anount of water flow out to waste water tank. The tank is small a you have to clean it every day. Using this funnel you can put the waste water into…
with an S for Steam Category: Kitchen & Dining
3MF file is for the U1. It has the logo. STL has no logo. Easy print! Let me know how it fits for you!
I wanted a descaling container that would perfectly fit my coffee maker, a DeLonghi Magnifica Evo, and still be used (after the cleaning/descaling process) as a storage container for all the brushes I use to clean up regularly the coffee…
The Delonghi Magnifica S is a bean-to-cup machine that comes with a manual steam wand. This wand is fitted with a nozzle for directing the steam, and a cappuccino sleeve locking the nozzle in place. The sleeve is great for creating bubbly…
The drip tray consists of two parts, the base, which holds the drips and a grid that sits over the top. After I made and tested it, I think you can skip the grid on the top. There are specific feet locations that the coffee machine sits…
My kitchen cupboards hang quite low and it was a pain to refill the beans in the machine. So I designed printed this funnel that replaces the original lid. It makes it really easy to pour in more beans. You also get a lot more volume,…
New : V2 – vylepšená varianta V2 Improved design with integrated drip tray handle Toto je vylepšená verze (V2) původního držáku mlékovače pro Delonghi Magnifica Evo . Základní myšlenka zůstává stejná – čisté a bezpečné uložení mlékovače…
Do your coffee machine splashes coffee everywhere even with the dispenser lowered? Well this little thing will allow you to put your cups 3cm higher. The raiser have little feet to lock itself in position using the holes of the plate, and…
I've used the base profile of original model and redesigned the cup to use while carafe is attached.
should suit all Magnificas, i guess. but these for sure: ECAM 21.110 ECAM 21.117 ECAM 21.210 ECAM 22.110 ECAM 22.320 ECAM 23.210 ECAM 23.217 ECAM 23.240 ECAM 23.420 ECAM 23.427 ECAM 23.440 ECAM 23.450 ECAM 23.460 ECAM 24.210 ECAM 24.450…
The original container only holds 250 g of beans, which means constantly refilling it if you use the machine often. This remixed extension increases the capacity to 1 kg while still allowing the ground coffee lid to open fully. So you can…
This part is the lever of the infuser, on a Delonghi Magnifica coffee machine. Printed with ASA, using 0.15mm layer hight. Works like a charm with a little bit of grease.
After searching and trying many other models for Continental or Veyron model scopes, they just never sat right. The knurling pattern used on the Sentinel is different and so the ring always sat on top of some teeth. After a few versions…
This stand transforms your smartphone into an improvised magnifying tool, ideal for comfortably and efficiently inspecting small details. Specifically designed for examining components on electronic boards, it allows you to take precise…
The De'Longhi Magnifica Start has an issue with the steam triggering the touch screen button power, which stops the latte and cappuccino process. Made this tinker cad it's my first model and I attached it to the De'Longhi icon. I attached…
Narrow funnel has also fine ribs pitch - fine ground coffee is better to use or shake a little bit when inserting the ground coffee. Tested on DeLonghi Magnifica S.
Delonghi Magnifica S ECAM 21.117.B Thermos extender. Workds for Contigo thermos (and maybe others)
Its sometimes hard to find a suitable container to decant the descaling fluids. This jug will take a whole cycle of liquid and sits under the nozzles. It is probably usable with other machines. When not descaling it fits on the shelf in…
Tired of constantly buying original steam knob (which is known to break after some time) I designed a better version. I recommend printing it with PETG, 100% infill for maximum durability and 0.2 mm layer height. I think satin print sheet…
The shape of the object is super nice and fits. According to the attached photo of the author, I have a slightly different model, namely DeLonghi Magnifica Evo ECAM29x.5Y EX:1. I don't know if it's due to the different model, but the…
EN : Replacement for a measuring spoon, based on the great design by David Pye. Vol.: approx. 1 cubic inch, = approx. 16,5 ml Material : PLA / PETG Layers : 0.3 mm Supports : none…
Included is a model for the extended eyepiece for 6X magnification as well as a model for the eyepiece cap that goes over the lens to hold it in place. Uses the same fasteners as the original eyepiece (M3 x 10 mm, or the slightly longer…
The place where the coffee machine stands does not allow for easy refueling of beans. Thus I designed this adapter, which can be kept in place, to make filling easier. Test with: De'Longhi Magnifica S ECAM 22.110.B (by me) If you tested…
Tumbler support for Delonghi magnifica Evo. This part help the tumbler stays 40 degree and you can fill it with coffee. Using milk carafe is not possible only for coffee types without milk. In order to get heavier backside or the support,…
I made this phone mount to fit a Harbor Freight spotting scope using the MagSafe phone mount. (You can find many cases that are compatible. You can use the phone's camera to view through the spotting scope, providing an easy-to-view image…
delonghi magnifica espresso machine knob V2
Designed this simple part to replace a missing rubber foot on my father's De'Longhi coffee machine. Even with just 2 perimeters and 15% infill it's not as flexible as the original rubber foot, but it fits and does the job. I'm not sure…
Funnel for Delonghi Magnifica S. Entonnoir pour Delonghi Magnifica S. Pour transférer directement du moulin à la machine.
A housing to hold the viewfinder from a broken Voigtlander Vitomatic 1 (or 2) Camera. They have very nice, bright viewfinders, and are easy to find broken. This makes for a great external viewfinder for rangefinders or other cameras that…
Lid for milk jug De'Longhi Magnifica Start Coffee Maker: https://www.amazon.es/dp/B0BV3B7T33?tag=offertunity-21&th=1 https://savify.eu/s/B0BV3B7T33 Category: Kitchen & Dining
Simple TPU plugs for the DeLonghi Magnifica S drip tray grid. Prevents single mugs from being placed off-center, eliminating accidental coffee spills into the tray instead off into the mug 😉 Quick print, no tools required Less than 1 g…
I designed a purge cup to sit on my DeLonghi Magnifica Evo (see picture) tray, fitting its contour nicely, in order to avoid having to have the purge coffee always accumulated in the tray. It is kind of boxy with some room for holding it…
Here is the updated product description in English with your exact dimensions included: Title Ideas * De'Longhi Magnifica S Bean Hopper Extension Lid Replacement * Custom Bean Hopper Lid / Cover for De'Longhi Coffee Machine (214 \times…
Auffangbehälter für Milch, Magnifica S Kompatibel mit De'Longhi Magnifica S Modellen Der Auffangbehälter für Milch ist ein unverzichtbares Zubehör zur Aufnahme überschüssiger Milch während des Aufschäumprozesses. Speziell für die…
You will need…. Harbor Freight magnifying lamp. https://www.harborfreight.com/fluorescent-magnifying-lamp-60643.html Kotto fume extractor.…
If you have some small parts or accessories for making coffee with your Magnifica S and you don't know where to put it and you want to keep it near your coffee machine, then this might be your solution. Just slice and print your part and…
Halter für die Heißwasserdüse zum Aufstecken auf die Lüftungsschlitze der Mittelklappe für Pulverkaffeezuführung. Einfach Oberteil anhalten und mit Unterteil feststecken.
One of the issues with the DeLonghi Magnifica coffee machine is that the steam activates the buttons, which causes problems when we want a large coffee. That is why I created this steam deflector. optional attachment system. be carfull…
Screw an Illy 250 g bean can on upside down and let the beans feed straight into the grinder. A built-in gate seals the chute, so you can swap cans without spilling a single bean. BeanDock replaces the hopper lid of the De'Longhi…
I was looking for a drip tray to descale my De'Longhi Magnifica S coffee machine and found this version, which I liked because of its design. I simply removed the feet (otherwise there would have been too much plastic waste to create…
Make descaling your automatic coffee machine easier with this simple model! Normally, you need to find just the right container to fit under the outlets and empty it multiple times during descaling. With this model, you can collect the…
Funnel for Delonghi Magnifica S. Entonnoir pour Delonghi Magnifica S. Pour transférer directement du moulin à la machine.
3MF file is for the U1. It has the logo. STL has no logo. Easy print! Let me know how it fits for you!
The shape of the object is super nice and fits. According to the attached photo of the author, I have a slightly different model, namely DeLonghi Magnifica Evo ECAM29x.5Y EX:1. I don't know if it's due to the different model, but the…
Adapts perfectly to the top metal platform. ⚠ Sugar dispenser must be printed in 150% scale ⚠.
Same point as the original, this is remixed from ( DeLonghi espresso machine pre-ground coffee funnel cap by Petclaud - Thingiverse ) . Useful if machine is used in a shared area by people that may mistake the grounds funnel as the bean…
EN : Replacement for a measuring spoon, based on the great design by David Pye. Vol.: approx. 1 cubic inch, = approx. 16,5 ml Material : PLA / PETG Layers : 0.3 mm Supports : none…
I wanted a neater more slimline zoom lever for my field target scope so I came up with this. This is designed to fit on Mk1 Falcon T50, its untried on other scopes so I'm currently unsure if it would fit any of the other Falcon scopes. It…
Remixed (split) to have two parts so i can print on the MK3S+. Love the design so kudos to origianl designer
