Liczymy pasujące modele…
End piece for the Mendelmax 20mm x 20mm aluminium profile. Reduces the risk of injury and gives a pretty look. Category: 3D Printer Accessories
Be sure and take a look at the latest version of these lightbars here: http://www.thingiverse.com/thing:1803781 This is a simple re-angle of the existing LED mount clips by Flurin, to allow the LED strip to point down towards the heated…
trochę ulepszone elementy drukowane na mendelmaxa 1.5 - z podwójnymi osiami Z, bardziej solidne. Możliwość montażu dual-Y silników do napędu stolika (np do zrobienia MendelMaxCNC) Możliwość montażu dwóch silników X (po obu stornach) do…
The following project will allow you to install 2 fully supported THX Linear Rails in place of the Z Axis 8MM linear rod found on the Lulzbot AO-10x series printers. It also upgrades the Z endstop for additional precision. PREREQUISITES:…
A few mounting clips to clip a common 12 power supply to the inside of the mendelmax frame under the carriage NB this protrudes 10mm under the Mendelmax. You need to raise your mendelmax on feet of some type. I used…
Set of filament guides for a MendelMax printer. I have had all sorts of problems with filament tangling during printing, so I created these guides to eliminate any possible issues. It includes two options for the upper guide- one fixed…
This is a part from my MendelMax 1.5 variant. The design have single piece z motor holder.
Attaches mechanical endstop switch to the inside edge of the MendelMax frame. Print instructions Category: 3D Printer Parts Instructions This mount attaches the Y-Axis mechanical endstop switch to the inside of the mendelmax frame. It…
A simple power pannel for the Mendelmax. To mount a very common power switch and power plug from a old PC power supply Print instructions Category: 3D Printer Parts Instructions Print, file switch hole a little to fit (deliberately very…
This is a Y-axis belt tensioner for the MendelMax 1 / 1.5, using a 16-tooth GT2 pulley and an M3 bolt. I designed this because the original MendelMax Y axis idler/tensioner and every other design on Thingiverse (to date) all use a 608…
This project expands on my previous Linear Z Rail for AO-10x project to incorporate a pair of Z Ballscrews, 10mm X rods, and the Taz 4 X Carriage assembly, allowing the AO-10x Series printers to utilize newer toolheads, up to and…
A top vertex designed so you do not need to drill a hole for a blind tap. Instructions Slide the extrusions into place, the stubs are designed to grip the extrusions in place(see second picture). STL has been processed with cloud.netfabb.…
Custom z rod clamp for use with 10mm rods. You can find the top vertex and the motor holder in the collection.
This is a 200mm fan mount to attach a 200mm fan to the frame of MendelMax. Instructions Print it Mount it Mount the fan ? Profit Category: 3D Printer Parts
This is a heavy duty, rock solid mount to attach the Gadgets 3D LCD to a MendelMax or any other printer that uses extruded aluminum profile as its frame. Original solid model files are in Solidworks 2013 format. 2014.06.21 Update: Added…
The internal Y rail mount by MishaT is great, but if you have a Lulzbot AO-10x series, the existing wiring for the motor is too short to run the motor on that side of the rail. So, this is simply a mirrored version. I claim no rights to…
This is a part from my MendelMax 1.5 variant. The design have single piece lover vertices.
This is a simple mount for the 12v to 24v converter supplied with Trinitylabs Y axis upgrade kit. NB 50cm fan pictured is not part of the upgrade kit. I added this after numerous warnings that it gets very warm. Print instructions…
This is a retrofit clip designed to slide onto a 3mm thick aluminum heated bed retention plate, which will raise your heated bed cable up enough to eliminate the risk of pinching it at full Y extension. It should slide onto the heated bed…
After fighting with the lack of Z height caused by my hacked addition of an E3D Titan and E3D Lite6 hot end to my MendelMax, I thought to try a vertical X axis, to hopefully move the Titan's filament feed slightly rearward and gain some Z…
From the original single spool holder designed for BCN3D+ by BCN3D Technologies, I would like to share with you this "derivate" in order to upgrade it into a double spool holder which uses less parts than two single holders. It's great if…
Made for 8mm leadscrews and lm8uu. Check the specification image to see if the leadscrew nut matches yours. The idler is designed for a GT2 belt, meaning dual 624 bearings on a M4 bolt instead of the usual 608 and M8. Source and…
A fully parametric clamp to attach quadratic objects like a oil bottle to the frame of the MendelMax Instructions Print it Mount it ? Profit Category: 3D Printer Accessories
This is a pair of brackets for mounting the Meanwell LRS-350-12 to a MendelMax 1 or 1.5. The brackets slide in between the two horizontal 2020 extrusions on the base of the MendelMax, and hold the PSU away from the frame. I'm using…
Designed to mount across the bottom extrusions or in the bottom corners (see photos). You can find the openscad file at github . Instructions Uses M5 10mm bolts with washers for the tabs (and t-nuts) and M3 20mm bolts for the side bolts.…
Yes, I designed a small upgrade for a 12 year old printer. I wanted a vertical x-axis similar to the Prusa MK4, however the hardware I have on hand is from my old Mendelmax, specifically; 16mm brass bushings for the vertical guide rods…
This thing will help you transporting your Mendelmax printer from A to B. Instructions Print the following parts: 2x HandleSide4MendelMax 1x Handgrip4MendelMax Vitamins (to buy): 2x screw M5 x 20 2x screw M5 x 10 2x nut M5 (Nyloc) 2x…
This is a clamp to attach round objects like pencils to the frame of the MendelMax Instructions Print it Mount it ? Profit Category: 3D Printer Accessories
After successfully getting as much Z height from my first MendelMax as I could with these carriages: MendelMax Vertical X Axis Carriages I promptly dismantled it and sold its frame to fund a self-built Prusa i3 clone. Long story short, a…
This is vertical x-axis for the MendelMax 1.5 (or any printer using the same rod distances). It is designed to host the 3-color Diamond Hotend ( http://www.thingiverse.com/thing:720520 ) . There is also an provision for adding a SP90…
This is a 22mm bearing block for the z axis lead screw built into the top vertex (flush mount) for Mendel Max 1.5. Tools are imperial so if your system is in mm scale to 25.4mm/in or 2540% Category: 3D Printer Parts
Based on https://www.thingiverse.com/thing:267212/files adapted to work with e3dv6.
This is a reinforced version of Phaiax's spool mount. It can be easily mounted on the MendelMax 1.5, or any printer based on aluminium extrusion. I had a spool too big to fit his mount, and it actually broke the support. So I made a…
If you happen to have a MendelMax 1.5, and it happens to use the old fashioned rod clamps for the X, Y, and Z end stops, these objects here: XYZ End Stops for MendelMax 1.5+ are incredibly useful. However, if you're like me, and have a…
Inspired by other similar designs here on Thingiverse. The rollers are made from 7/8" Aluminum round stock drilled and tapped 5/16"nc on both ends. Use small washers to keep the knobs from tightening against the bearing race. Cut the…
By using this solution one motor for the Z-axis can be replaced by two 32 teeth T2.5 pulleys and a 950mm T2.5 belt. This modification offers several benefits like: less weight less wiring less noise reduced costs Z-axis can be moved by…
This thing should help you to fix your Megatronics 2.0 board on your MendelMax printer. Easy, stable and dependable mounting. Update: This version has several 3mm holes where you can create a pull relief for the cables by using small…
I designed this small support to hold a couple of 40mm fan, the plate is made to fit aluminum profiles of a mendelmax 1.5! I'm using it as part of the cooling system of the electronics. UPDATE: User @Ubermeisters try it on his Mendel max…
This is my mount plate for my Bowden extruding setup. This allows you to mount a standard extruder to the printer, insert 2 nuts onto the tube and extrude away. See it in motion at http://www.youtube.com/watch?v=9oZIQ9wZ22k Category: 3D…
My trusty MendelMax 1.5 from 2013 is showing it's age and it is the second time I modify the X axis. This time after using a CR-10 V3 I decided to opt for rollers instead of rods and Igus bushings, so, I bought a fully mounted CR-10 pro…
This is a remix of the upper piece of "Amplivibe's E3D v6 for MendelMax" . I narrowed the rounded part of the upper piece by 1mm so it would it sit properly in my X carriage. (Not sure exactly which X carriage I have - it's circa 2011 or…
remax fm http://www.thingiverse.com/thing:106281 not test yet. Category: 3D Printer Accessories
I had issues with my mini tripod and LifeCam Studio when recording or streaming prints. So I designed a mount that held the camera at the popper height, and synced the printer's vibrations with the camera. The result was a much more…
The Mendelmax 3 LRU has an MGN12H on the front of the X gantry and belts on the top that are vertical. The carriage was modified from Voron's Design, so that the belts can be clamped one at a time at the top of the carriage and should not…
