Liczymy pasujące modele…
I designed this part to fit my DJI O3 Air Unit. As you can see on the pictures the big ass box fits right behind the cam. I used double sided sandwich tape in-between to stick it to the upper frame part and secured it with a zip tie. I…
DJI O4 Pro air unit antenna and camera mount for QAV-S Mini Antenna mount Test print use Bambu lab P1S 0.4mm nozzle and eSUN eFlex TPU-87A TPU with support Camera angle is limit by top plate or need to move the camera forward Camera mount…
Converting my QAV-S JB to Walksnail Avatar, I wasn't able to find a dual antenna mount, so I decided to quickly put one together. I printed the part with 100% infill and 100% part cooling to, so the steep overhang prints properly. Make…
To fit my drone's frame I had to extend the rear holes 0.9cm further back. I redrew the part based on Frugols design to extend it. I also changed the width of the three mount-extrusions to 2.8mm, 3mm, 2.8mm, as the official go-pro mount I…
printed in TPU. I made this so my TBS crossfire antenna wires go underneath the two upright camera mount plates and your T antennas clip in. This is fit on my QAV-s Joshua bardwell edition, idk if the other versions of the frame will fit…
Camera Mount for DJI O4 Pro Camera, fits a ZMR250 frame.
simple model
This model is a mount of the dji o3 air unit antenna on the JB edition QAV-S frame
This model is a mount of the dji o3 air unit on the JB edition QAV-S frame
This is bando boot for QAV-S JB edition frame. Fits T-Motor F40 motora.
Threw this model together to mount my T-shaped ELRS antenna below the mount for my rhcp antenna, on the tail. I pulled the outer dimensions from pokey_fpv's mounts, but the model is otherwise from scratch in Fusion 360.
Update: new v4 added. Changed directions of antenna, and made it easier to plug them in. Plus possibility to add a PCB LED strip (Lumenier Digital RGB Arm LED Board) This is a remix from drewzh (thanks mate). His intentional design was…
Arm guards (with skid pads) for Lumenier QAV-S Joshua Bardwell edition frame. Supports 2306 and 2207 motors.
Small Feet for the Luminier QAV-S Mini frame.
There's a few other ELRS antenna mounts out there for this frame but none of them fit so I had to design my own. This one fits the 6mm standoffs that come with the frame. The beveled cuts on the top allow the mount to sit flush with the…
Support en TPU pour avancer la gopro et laisser place a une batterie plus longue à l'arrière de la gopro. de plus ce support apporte une bien plus grande rigidité pour la gopro et évite les vibrations. EN : TPU mount to move the GoPro…
20 degree angle mount. I am not the original designer of the case part. I do not recall where I got it from.
Lumenier QAV-S Mini 4" Freestyle Frame Skids After beating up my drone for a few flights (top mounted battery setup) I designed some skids. These can be printed in almost any filament type, but I've found that TPU is more durable. I…
See pictures, VTX antenna go up, RX antenna out the back.
for mounting GPS receiver on quadcopter drone on the nose over the FPV camera FITS: Lumenier QAV-S 2 Sub250 Joshua Bardwell SE 3in frame link HGLRC M100_Mini GPS link MATERIALS: TPU 95A (optional) M3x6 or M3x8 screws (4 each) PRINTING…
VTX antenna holder for original Caddx Vista antenna for Lumenier QAV-S. Print in ABS or PETG Also look at my other QAV-S models: QAV-S Skids https://www.thingiverse.com/thing:6121858 QAV-S Stack Protectors…
Designed this to mount my RDQ Micro M8N GLONASS GPS to my QAV-S JB Edition frame. Definitely print in TPU as the mount will need to bend a little bit to tighten the screws onto the frame. Screw the mount down BEFORE zip tying the GPS to…
This is a model for the QAV-S JohnnyFPV edition. It is a simple mount that goes between the air unit and the top plate.
Left and right stack protectors for Lumenier QAV-S. Print in ABS or PETG. Also look at my other QAV-S models. QAV-S Skids https://www.thingiverse.com/thing:6121858 QAV-S Caddx Vista Antenna Holder https://www.thingiverse.com/thing:6121848…
Originally designed for the lumenier QAV-S 2 JB edition, but it should work for any 6mm standoffs with 19mm spacing. Printed in TPU with supports
Holds the FPV antenna on the QAV-Skitzo. It slides onto the standoffs and has holes to pass a zip tie so it holds firmly against the top plate. ** (28.07.2017) added v2 which has a slicker design Plan to: Add a way to secure also the RX…
I wanted a simple adjustable angle FPV bracket for my Crazepony (Crazypony) H210 and 700TVL FPV camera. I couldn't find one that I really liked to I put this together. It's intended to be adjustable, simple & lightweight. I also included…
This is a quick design of a GoPro base mount for QAV-S JohnnyFPV Special Edition frame
Small lightweight Caddx Vista antenna mount for the lumenier QAV-S 5'' quad. Printed in TPU with a 0.2mm layer height, 20% infill, no supports needed. Antenna is mounted with two M2 x 8 screws and two lock nuts. Print Settings Rafts: No…
This is a quick resize for the DJI O4 Pro Antenna Mount on the Joshua Bardwell Edition Luminier QAV 5". I did have a little stringing in the antenna holder that I was able to clean up by poking with a soldering iron.
Antenna holder for TBS. Keeps enough space for DJI O3. Antenna is sturdy mounted on the frame. I printed it with Ninjaflex TPU which works great. Support is needed. Betaflight Dump for anyone cine like fpv setup. Aikon F7 AIO 4S with 1404…
Left and right stack protectors for Lumenier QAV-S. Print in ABS or PETG.
A Holder for the Antenna witch can be secured by shrink tubing. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: Yes Category: R/C Vehicles
VTX antenna holder for original Caddx Vista antenna for Lumenier QAV-S. Print in ABS or PETG
This is a bracket for the aft end of the QAV-S Bardwell Edition 5" drone frame. It is meant to support a VTX antenna using an SMA panel bracket with two M3-6 screws. It also holds the MATEK SAM-M8Q GPS antenna. Both antennae are oriented…
Remix of: https://www.thingiverse.com/thing:4936338/files Lumenier QAV-S JohnnyFPV Special Edition Hero 8 Mount
This is a 30 degree camera mount designed for the Lumenier QAV-R to suit the Runcam 3 or GoPro Session cameras. It has been designed to take mounting straps up to 20mm wide. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No…
Rafts: No Supports: Yes Infill: 30% or more Filament material: PLA
Lumenier QAV-PRO 3.5" Mini Whoop - Immortal T Crossfire Mount and DJI O3 Air Unit Isolation Pad
This replaces the rear standoffs on the Lumenier QAV-S 5" Freestyle Quadcopter Frame - Joshua Bardwell Special Edition to allow a DJI air unit to be mounted. You'll need some M3 nuts and snap/melt them into the provided nut cutouts to…
I intended to utilize my HDZero Nano v2 Cam in my Lumenier QAV-PRO Micro Whoop 2.5'' drone. I printed it in PLA, and it functions well. Additionally, it offers some protection for the camera and can be securely fastened using the original…
Tiny mount for the Lumenier QAV-PRO Micro Whoop 2.5'' Micro frame. Allows you to mount: HDZero Whoop LITE VTX TBS Crossfire NanoRX Best printed in TPU, see pictures for assembly.
This is a custom 2 in 1 antenna mount for the old X210 / QAV-X frame, I re-worked my old quad and improved the VTX (added HD-Zero) and ELRs for control. So far printed this in PLA+, but likely I anticipate with one good crash it will need…
Building the Joshua Bardwell QAV S2 3" and the DJI O4 Lite antenna is known to be too short. This mount makes it work
other side has to be mirrored in slicer for clean nanoRX installation i recommend this print https://www.thingiverse.com/thing:4731250 if you like this give me a sub on IG or YT https://www.instagram.com/martymcfly_fpv…
Second Version of my Runcam Thumb Pro Baseplate for the Lumenier QAV-S Bardwell Edition FPV Frame I have to reprint mine so I make a few improvements. The Cam is more in the front. The Screw-Holes are tighter A Version with a mount for a…
This is a gopro mount for lumenier QAV-S I made for mine because I have telesin nd filters. The mount has a 30° angle.
printed in tpu with little support if you like this give me a sub on IG or YT https://www.instagram.com/martymcfly_fpv https://www.youtube.com/channel/UC0Ps_VxWIuz_74Qz01wQ68w Category: 3D Printing
Beautiful smooth VTX Antenna Mount for QAV-R quadcopter frame. Also compatible with QAV-210. Print Settings Printer Brand: TEVO Printer: Tarantula **Rafts:** No Supports: No **Infill:** 60% Filament: BQ PETG White Notes: Support me on…
i printed in tpu 95a at 60% infill with organic support (which is not needed)
It´s a holder for the FrSky X4R-SB, between the two back pillars of a QAV250 / ZMR250 Quadcopter Frame. Category: R/C Vehicles
Beefier ducts for the FPV Lumenier QAV- Cine 3
It fits very well. It is hold by 2 zip ties. That was the only possible way for me. I used 3DJake A95 TPU Blue. Hope I could help you out. :)
Antenna mount for Lumenier QAV-R 2 Slam. Use TPU for best results. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: .12 Infill: 25% Filament: Sainsmart TPU How I Designed This =================== Designed with Tinkercad…
Three mobius/runcam mounts for the Lisam210 and QAV210 quadcopter. Holes for strapdown, but im mostly using velcro. Print instructions Category: R/C Vehicles Summary Three mobius/runcam mounts for the Lisam210 and QAV210 quadcopter. Holes…
So I designed a tray with 30.5x30.5mm holes to mount stuff in my old QAV250 frame, I was to busy to put larger threaded screws, so I made tthis tray for my VTX in this case. --The rod version has 4 rods in place of the holes as seen in…
Landing feet designed to specifically fit the JB QAV-S 2, 5" drone Printed with a Prusa MK3, I used 80% infill and M3x8mm screws. Other prints just didn't quite have enough wiggle room in the bolt pattern. These fit flawlessly! The TPU…
print it in abs , you will need 4 M3 screws and 4 nuts you need to flex the part to put the gps in and then screw it in the frame
This Object lets you mount the TBS Unify antenna (and your RX antennas) on your Lumenier QAV-Skitzo Dark Matter. Printed in TPU (NinjaFlex) for maximum durability and also to protect the antenna on impact due to the flexibility. Other…
This Object lets you cover the arms of the QAV-Skitzo for additional protection. If there is the interest, I could also add a motor shroud to protect the motors also if required. The v3 is doubling as a arm bumper and motor soft mount.…
printed in tpu 0.32 layerheight .. lay on side... rear is mounted with ziptie for any kinds of gopro... i use it without battery powered by iflight balancer cable. 1405 4800kv t-motor and gemfan d63 .. works flawless angle 15° if you like…
A 9mm spacer for the PDB that replaces the 4x 10mm aluminum spacers. Light, offers a bit more protection for the PDB/ESCs. Inspired by the QAV250 spacer sold by FPV-FreeFlight but clean-room re-implemented from scratch as an Open Source…
Canopy pour GEPrc Chimp 6" Compatible avec d'autres frames. Ajustez éventuellement le scale x ou y suivant vos besoins. Insert metalique 6mm de long :…
there were manny errors on the initial design. Fixed them and remixed it Thanks for the design Krischan1986! ;-) Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest dieses Teil haben? Schreib…
The GPS mount is made for the TBS M8 GPS.
Rafts: No Supports: Yes Infill: 20% Filament material: PLA
Rear dual antenna mount for receiver (RP1) and VTX antennas with a swappable VTX antenna SMA connector. Printed in TPU with a brim for adhesion. It has survived quite a few falls, so I thought I would share.
QAV210 x4r/d4r receiver mount i use sbs filament Category: DIY
Got fed up of having to keep on Hot Gluing my buzzer back to the quad frame... This mount slides on the the rear supports... Decided to cut the support hole in half, so as to avoid the rotation of the props and therefore not interfering…
This predates me learning FreeCAD and thus lacks source files. To make edits you can visit: https://tinkercad.com/thing Requires: - 4x M3 16mm screws - 4x M3 lock nuts
I needed some kind of antenna mount for the Radiomaster DBR4 Receiver for my QAV-S JB edition. Probably not the best idea to mount the antenna at this position but it does the job. If you need a left and right version just mirror it.
This is a mount made to hold the following LEDs: http://www.readytoflyquads.com/led-decoration-board-set-7-30mm Will fit both the QAV210 and the QAV180 from Lumenier. Category: R/C Vehicles
This Object lets you mount a FrSky XSR and a buzzer on the Lumenier QAV-Skitzo Dark Matter. Printed in TPU (NinjaFlex) for maximum durability and also to be able to fixate the buzzer (press fitting). Other things for the Lumenier…
QAV 250 LED strip back light - Starwars Category: R/C Vehicles
Foxeer Box2 mount for given frame: https://www.aliexpress.com/item/32829319009.html (mount holes are on 30x42 rectangle) Was printing without supports, with TPU filament. Taking into account I have a bowden printer, without supports, the…
QAV210 Lumenier, mount for Gopro Session add V2 version. more durability add V3 version. much more durability Category: DIY
A compact base for the Tarot T-2D Gimbal to moint it to a TC-R 220 or a QAV-R. There is no place to mount the controller yet, so you have to find a way how to mount yours. I screwed a small plate to the top plate to which I zip tied the…
One of the first things I decided to design for one of my quads to try out my new 3D printer... Made it using ABS, as that is all I have... Had a few crashes, holds up well so far, no damage at all... Version 2 holds up a bit better...…
Foxeer Lollipop mount for QAV-X/XS Racepod. Category: R/C Vehicles
Rafts: No Supports: Yes Infill: At least 20% (100% recommended) Filament material: PLA
A VTx holder for the QAV250 frame Category: R/C Vehicles
The QAV Piko 2" micro frame is great, except the method employed to hold the battery. A rubber band is used and wrapped around the battery and engages two "ears" on the frame. Removing and replacing the battery was an exercise in…
Eachine ET526 mount for QAV-Skitzo frame. Print Settings Printer: Tevo Tarantula Rafts: No Supports: No Resolution: 200 Infill: 20% Category: R/C Vehicles
Print with TPU than insert the R9 mini into the hole.
A tray for the Eachine TX526... Uses the frame spacer poles to attach, also allows fo cable ties, if you wish... As you can see, easy access to the Button and Display... Print Settings Printer Brand: Prusa Printer: Prusa Clone **Rafts:**…
Rafts: No Supports: Yes Infill: 100% Filament material: PLA/ABS/PETG/Metallic
This Object lets you mount a GoPro Session 5 (and probably 4) on the Lumenier QAV-Skitzo Dark Matter with an angle of 20°, 25° and 30° degrees. Printed in TPU (NinjaFlex) for maximum durability and also reducing vibrations in the recorded…
just cut buttom off to make it support-free Category: R/C Vehicles
This is a CADDX Peanut Support for the QAV-S Joshua Bardwell Edition Frame. I didn't do much design on this one, please be sure to check the sources and thank them :) Category: R/C Vehicles
Rafts: No Supports: No Infill: 10% Filament material: PLA
my qavx realacc version race pod weighing 21grams and holds runcam micro version 1-3 at a 35 degree angle. the rear mount will hold an rxsr and TBS unify style vtx antenna. you don't need to use the rear mount this will bolt right up to…
print it in abs you will need 4 M3*4 nuts and 4 screws print the antenna mount in to pieces
Print in TPU 95, 100% infill or enough walls to make it 100%.
there are 2 mounts in here one is if you want to mount the camera high and partially unprotected and you will need M2x6mm screws for the camera, this provides a snug fit with plenty of build room behind it. also a little protection.…
my qavx realacc version race pod weighing 21grams and holds runcam micro version 1-3 at a 35 degree angle. the rear mount will hold an rxsr and TBS unify style vtx antenna. you don't need to use the rear mount this will bolt right up to…
I used TPE but any flexible material will work fine, the gopro lens is completely covered and with 10-15% infill it has come cushion from impacts. use a zip tie through the slot in the back to keep the gopro angled up. Print Settings…
I made this so i could cleanly mount the Diatone antenna and the FrSky R-XSR rxsr receiver. Print it upside down as it would be on the quad VTX i'm using is a diatone sp3 but any VTX with the 8mm rear nut will fit this. i plan to make one…
Building the Joshua Bardwell QAV S2 3" and the DJI O4 Lite antenna is known to be too short. This mount makes it work
Rear dual antenna mount for receiver (RP1) and VTX antennas with a swappable VTX antenna SMA connector. Printed in TPU with a brim for adhesion. It has survived quite a few falls, so I thought I would share.
