Liczymy pasujące modele…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
Designed some taller case feet for Mini ITX cases, specifically the KXORS S300 and S400 to help with bottom air intake. Original feet are 10mm tall, so I created 20mm and 30mm variants. The 20mm variant height is approximate. The hole…
This is an IMMOBILE vent insert. It is meant to replace all moving internals via friction fit. Printed in PA612 CF (probably overkill) but fits nice and snug. I suggest painting in your supports just along the louver edges. The client…
replacement end cap for those of you who've lost yours, plenty strong enough with 15% support but you may go higher, if you decide on fuzzy walls, make sure you only do the contours not the hole, it'll ruin the thread.
Matches taper on torch body to hold securely. Torch snaps into and out of holder. Mounts to wall or whatever you care to with three #8 screws (I used simple plastic wall anchors). The source ViaCad model is included, though I didn't…
Some low profile rail options for the ZWQ S400 Zebra, pretty much as low as possible while keeping the front section functional. May not fit all picatinny attachments on the first 5 sections due to how close the rail is to the part. There…
Based of the stock butpad but increased to 45mm in length. please note that the end of the blaster isnt completely flat, so you might have to trim and/or shim the space between the blaster body and butpad for it not to wiggle around.…
Here is my wall mount for a Xiaomi Body composition scale S400 :-) You need to print 2 pieces. The model is simetric if printed on the flat edge in the corner. You can print it without support. I used white Marble PLA with 4 walls and 20%…
Cover plates for the exposed plunger tube on the ZWQ S400 Zebra/Red hare. Features a decorative topographical pattern of one of the fields I play at. Print with a brim if you have adhesion issues. I recommend adding some adhesive of your…
A selection of different throat inserts (aka table inserts) for the Record BS400 bandsaw. I printed mine with 100% infill, mainly so that the one without a slot could have its slot cut by the bandsaw to create a zero clearance insert.
Designed for the Sony HT-S400 or HT-SC40(Costco model). Stands lift the bar 38mm, or approximately 1 5/8 inch. The “hook” on the back goes in the wall mount slot to reduce the likelihood of the bar getting knocked off the stands. Version…
V2 version, this one fits much nicer and is much easier to put on and off the case. The previous one was a very snug fit whereas this one, while still not being a lose fit, doesn't feel like you're going to pull the paint off the case. I…
This is a vertical stand for the S400. I could see a few for the S300 but decided I'd just make my own one for the S400 case as well. The vertical stand saves even more space on the desk than what this tiny PC case already saves in terms…
Air intake to carb boot for DOHC 1983 Yamaha XS400 Maxim. Designed to fit between stock Mikuni BS34 carb and stock air box. Made to use the stock clamp on the carb side. Inside diameter of the carb side is 55mm. Does not include the…
A rear angled free swivel QD point for the ZWQ S400 Makes use of the upper chicago screw that holds the magwell in place. Fits the threaded screw, not the internally threaded post. Ideally replace the screw with one of the slightly longer…
Here i Designed A Profile to replace one i lost while i moved to another Town. Print Settings Printer Brand: Anycubic Printer: Predator Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: Geetech PLA Black Category: 3D Printer Parts
The Record BS400 bandsaw has a quick release tension handle, which is really convenient, but it's easy to forget to tension the blade before starting the bandsaw. This magnetically-attached warning sign covers the power buttons to help…
Note, that the Black & Decker side is quick and dirty… I eyeballed the angle, which turned out to be a bit more shallow. It is also not as long as it could be - but I wanted to spare some minutes printing time. The shoulder inside is not…
Make sure you read these before you start making your mini WS400H Recommended to print on most 220mmX220mm 3d printers (Example: Creality Ender 3) For best possible structural capabilities, print with PETG and a pretty high density and…
Designed mount for webcam for our PWS400K. List of used parts: 2x M4 35mm 2x M4 heat insert nuts 1x M4 20mm 1x M4 hexagon nuts 4pcs zip ties
DO NOT USE TOO WEAK USE OTHER MODEL ON PROFILE : https://www.printables.com/model/996472-s400-mini-itx-case-inspired-by-formd-vertical-stan This is a vertical stand for the S400. I could see a few for the S300 but decided I'd just make my…
With this adapter it is possible to attach a funnel to the WS4003 anemometer. I have designed this funnel adapter to measure my air conditioning system at home. The adapter can be printed easily without support and with snappers not…
This is a vertical stand for the S400. I could see a few for the S300 but decided I'd just make my own one for the S400 case as well. The vertical stand saves even more space on the desk than what this tiny PC case already saves in terms…
Just a spring spacer for the s400. Scale vertically in slicer as needed. Use sparingly: You are likely to settle your spring with too much.
TriStand made Buchardt S400 mk1(180x240mm) where you source the wooden legs. The 3 legs are angled at 10 degrees BOM: 3 pieces of equalish length wood 12 (less is properly fine) screws (max 4,5 mm diameter the hole is 5 mm) to mount the…
This is a spare part for the Philco pas4000 vaccum cleaner holder. I basically got a image of the real one, get the reference of the real dimension and sketch over it. This is not a copy its only something that follow the original idea,…
This is the toolbox cover for a 1977 Yamaha XS400D. Other years & models of the XS400 might work.
Mounts to the top exhaust fans allowing a 120mm Slim fan to act as intake over the CPU cooler. Requires low-profile CPU cooler using 90mm fan. Best printed in PETG or other high-melt temp filament.
Put double sided tape or a bit of a foam for insulation between the cap and the spacer ring.
Printed clips to mark your zwq s400 springs (These 3 are specifically from 604blasters)
This replaces the DC coupler cover embedded into the battery cover of the Canon PowerShot S400 camera I used PLA .125 layer
Scheppach Vacuum Connector (TS4000) Anschlussstück für eine Scheppach TS4000 Kreissäge an eine Absauganlage
Part that holds the chain guard when you take off the wheel hugger
With all Lynx style blasters I always accidentally drop the mag by activating the mag release on my tac gear when I should the blaster. I modified the OOD model to take a ball bearing detent. You will need a 6x7 mm ball bearing detent.…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
Cover plates for the exposed plunger tube on the ZWQ S400 Zebra/Red hare. Features a decorative topographical pattern of one of the fields I play at. Print with a brim if you have adhesion issues. I recommend adding some adhesive of your…
Scheppach Vacuum Connector (TS4000) Anschlussstück für eine Scheppach TS4000 Kreissäge an eine Absauganlage
Make sure you read these before you start making your mini WS400H Recommended to print on most 220mmX220mm 3d printers (Example: Creality Ender 3) For best possible structural capabilities, print with PETG and a pretty high density and…
A rear angled free swivel QD point for the ZWQ S400 Makes use of the upper chicago screw that holds the magwell in place. Fits the threaded screw, not the internally threaded post. Ideally replace the screw with one of the slightly longer…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
The original emblem fell off my gas tank on a ride, so I matched the style of the original, and mounting pattern. The original had some contour to it, this is just flat, but once screwed down it conforms to the shape of the tank.
This is a conversion kit for the 1977 Yamaha XS400D glass fuses to blade style fuses. Below is the fuse box this kit was designed for. https://www.amazon.com/dp/B012CQEPN2 This kit includes: Mounting bracket for fuse box Ring cover for…
These are close to the original, they twist and pop up just like the original ones. You need to print two and glue them together. Sand tip a bit so the eject works.
