Liczymy pasujące modele…
This is a shorter snake that of course prints quicker, but is also stronger since there is less smaller links. If you are looking for the shortest snake, it can be found here: https://www.printables.com/model/856137-shortest-snake-v12
I shortened the height so I could use the original air duct. You can stick to the print instructions in the original model I just changed the size. Due to the temperature, PLA is a problem as it gets closer to the plate. The original air…
For the small version of the excellent "multifunction arm mounting system" there is a remix for a more stable bracket that allows heavier objects attached to the arm. I wanted to attach this bracket to my IKEA "Kallax" shelves (~38mm).…
Fits the newer Ender 3 Pro without needing to reverse bed bolts! The case is 52mm tall, so you can double check the bolt under your bed won't rub into the case. The 3rd photo shows which bolt to watch out for. This is a remix of…
This is a remix of Corefile's No Logo version , which is a remix of Joe's V4 version , which was a remix of FilamentCorner's version. My only complaint about the original versions of this handle was the length of the trigger. I like to…
This is a shortened dryer lint vacuum attachment to clean out lint that gets past your dryer lint trap. I just did it on my Samsung dryer and got a little bit out that looked kind of old so I'm glad it's clean in there. I used my older…
Shortened the design by cutting a chunk out of the middle of the track. Fits on more printers and prints faster this way
In order to save some space I reduced the original Anycubic Kobra 2 Pro spool holder to a width of 70mm. The original is 90mm. Compatible with my Anycubic Kobra 2 Pro Spool Mount: https://www.printables.com/model/855122 That combination…
Printed in PLA Plus, .2mm layer height and organic supports
This is a basic edit on the original Rack Stud by Erik Jeppesen to make it shorter and slightly more forgiving for lower-accuracy and lower-fidelity printers.
Remixed the base to fit with the original ams lid. It's 1.5 mm shorter than the original. Print settings They are the same as in the original model.
This is a Shorter under the drag chain connector for the SV08. Use supports. This uses the exact same 10x15mm Drag Chain that is provided by solvol. I get no kick back for this. https://a.co/d/bmJhGwp
Microfon holder remixed for the “Rode Wireless Go (II)” : https://amzn.to/3HWJ8ot (Partnerlink) Original description: "This is my version of Rode's Interview Go Handheld Adapter for their Wireless Go systems. Plug the Wireless Go receiver…
we needed a space to park and hide our robot-vacuum so i printed these legs to use that cheap ikea lack we had on the picture is the 120mm version, but 100 and 150 are included in the files as well i printed that in petg with 5 walls and…
I thought that the original box looked weird so i made it shorter. I suggest scaling it up 10% or more because the hinge doesn't print for me in the 0.2 tolerance and breaks after one use in 0.4 tolerance
Intex pool shorter skimmer.
I replaced the original screws with 10mm M3 cap head screws to attach to the printer. I felt the original screws were not quite long enough to securely attach through the bracket and side panel while accommodating for the extra thickness…
I didn't like how long RTM's keychain took to print, so I got rid of about half of the links to make it shorter! It's still a neat design that works great as a keychain. I printed mine with a raft to make sure all the little pieces don't…
Remix of the "Screw measuring tool, imperial" by cdlong. It's the Imperial Screw Measure Tool, but Shorter. We didn't need all of the diameters, so I knocked those off, made it shorter so it looks nicer, then added some magnet slots for…
made it shorter to fill out my 22x22x25 printer better, printed at 45 degrees at 23cm height Neo Kobra - Anycubic
When I tried out bday998 ‘s model on my printer I discover the hotend wiring was forcing the left duct down into the print. So I shortened it so I wouldn’t be putting pressure on the wire and the fan duct wouldn't drag across the…
Increased base height to strengthen and made less deep to make getting parts in and out a little easier. Supports: No Resolution: 0.3 Infill: 20% Notes: Sliced in Cura w/ Horizontal Expansion = -0.3
I created this to attach to the side of my house (where there isn't guttering) to hang our Christmas lights up (Merry Christmas by the way!). This is an alternative of my taller hanger with 2 screw holes. The picture shows the various…
A little tool to make it easier for you to paint the Easter eggs. An egg can be clamped between the two holders using the rubber band. The distance can then be optionally fixed with the screw. By turning the handle, the egg can be painted…
There is still ample space for the power cord inside the model. The "Einsatz" component remains the same, so if you have already printed that part from the previous model, you can reuse it.
I created a variant of the eyepiece mount that can be secured to shorter eyepieces too. I liked the original design, but I could only use it with my 25 mm eyepiece. With the new design I was able to use my 10 and 6 mm eyepieces too. BOM…
I don't know why, but for some reason a couple of years ago buffer tubes with battery compartments have dissipated from all of my favorite shops and they were never restocked. So I made this. Size: -Tubes are 145mm long, about a notch…
I liked the door seal created by Jia gantic but it did not fit right on my P1S - it would bind in the hinge if the door was fully opened. This remix cuts 0.8mm off the top of it and brought the legs closer together at the bottom for a…
Shorter LCD supports designed so that the MK3/S can fit inside an Ikea Stuva enclosure with a hole for the bed cables. There is one hole for each side, slightly smaller than the bolt. Use a m3x10 bolt to thread directly into the plastic.…
he same spool holder as the original but shorter. Ideal for those who use a side mount. As is not a structural piece, you can print in PLA without supports.
The original adapter here was unnecessarily long. To save space in my pack, I redesigned it in Fusion to be 18mm shorter. It also has some fillets and chamfers which make it less poky. Print with the narrow side down. No supports needed.…
Remixed the the nice model from @javawizard_449936 to a shorter version to get it printed in the bambu lab x1c and with this version you can pull them out and dont have to lift them. (made a version for 15 buildplates, should be enough to…
this is a shorter Version - fits a PRUSA and prints faster
Printed vertically, without supports.
Modified an existing remix to close the top on the RC2 style face shield. The remix this was based on is slightly shorter than the Prusa version to reduce printing time and filament usage. The model with no hex holes was selected to limit…
@fredster's version was too tall for my Platsa cabinet. So I shortened the long part to 160mm. So I can open both AMS so
Remix of "Q8Khajah"'s logitech keyboard stand. I reused the rubber feet from the broken stock logitech keyboard stands and just reattached them to the ones I printed. I used krazy glue to secure the feet more permanently to the printed…
I have a 3rd Gen Toyota Tacoma that also has a glove box organizer by JDMCAR that uses Joshua Dennis' Toyota Tacoma Glove Box Drawers . My dad recently got a 2024 Toyota Tacoma and purchased a JKCOVER Glove Box Organizer . He liked my…
I did not like the loud rattling of glass on plastic filament makes. I placed round furniture feet in the corners of the glass to reduce the noise. This made it still a little high and I also did not like the gaps. By reducing the height…
The original is very well designed and perfectly balanced. I couldn't fit the X-Wing on my shelf with the foils deployed so I remixed the arm. With the modified arm everything now stands 295mm tall with X foils extended. The arm is…
This is a model based on the kingdom class Starscream's null ray. Seeing that the next seeker isn't going to have some, this should be a good replacement.
Very simple model, easy to print. I did it with: Sunlu Silk PLA+ blue Layer height: 0.2mm Printer: Elegoo Neptune 3 Pro Slicer: Ultimaker Cura 5.3.1 Supports: not needed
This will go times 2 in my RC 4WD design (in progress) but it also drives (partly) of the overall design size. So I decided to streamline a little bit. I was able to design a print in place part (much shorter) but prone to breaking (!) So…
Straight Talon Mag [ 10 / 15 darts ] --> Horizontal Print --> shorter feed lips to be compatible with more blasters (e.g. ONTOS and MULTI-TOOL) --> for Talon Magazine springs (wire springs) This is a remix of the nice combination mod by…
HomePod Mini Stand
This is a shorter version of the container I did in Tinkercad.
I had to loosen heat bed's spring too much for it to touch the nozzle, which doesn't help with overall stability of the bed so I remixed a shorter bracket from tichoh's. Shorter brackets are in 40, 43 and 45mm length, just print one that…
Quick heads up: These remix designs were somewhat “intended” for the case being positioned on the X-max end (right side) of the LR3 gantry. If you are planning for placing it on the X-min (left side), then the only concern with simply…
I designed this myself 100%, I didn't edit the original, but since I did use the original for some quick measurements I think that counts as a remix. The changes with my duct compared to others is, it fits correctly. It isn't off-center…
Print it with normal supports
UPDATE 1: made a new model from the scratch – it's super tight fit and hard to install but worth it Description : This is a shorter version of the original model:…
Outlet shelf for a single gang GFCI outlet with a shorter overall length.
Big buildplate holder for wider slots for glas, carbon and PEX/dual sided PEI buildplates: 2x glas (thickness of the buildplate: 3,5mm - slotwidth 4,5mm) 2x carbon (thickness of the buildplate: 2,8mm → slotwidth 3,8mm) 10x PEX/dsPEI…
Stock Voron/Monolith BOM does not include M5x50 SHCS. The original model was a shy too long to use M5x40 SHCS, which should already be on hand. V2-beta changes: Choice to use an M5 T-nut instead of an M5 hex nut to increase contact area.…
A mod for the Blobifier mod that replaces the tray and servo arm with a rack+pinion mechanism to allow for a shorter base. Note: I'd recommend adding some plastic-safe grease to the rack and pinion interface to reduce wear and tear in the…
Remixed the original by Sergej to have a shorter cotton pad 'tube' since most of the time it would be half empty, which you can also see at most of the original makes. Use it to store your cotton pads, nail file, swabs, nail cutter and so…
Shorter version of the original draw latch that allows 6u boxes to sit flat when latch is closed
I slightly changed the lovely design of GrumpyNinja64 to my needs. The original file had a 1mm gap between the two parts and I extended the female part by 1mm. The lips where too long for me and I shortened them 3mm and changed the form…
Thank you for downloading my design. Remember to like the model if you download it! :) Check out the original design by dav88! Please consider offering me a beer if this helped you! PayPal: @giovannicolo // [email protected]
I printed with 3 walls and 15% gyroid infill With my settings (on my printer), the spool can hang from just 1 side of the hanger. The second side can be printed out for even hanging which looks better and offers additional support
I found the standard Carbon 13's proportions to be slightly off, legs too long, arms too short, so I just took the models and extended them.
This is a shortened mounting screw for the Logitech/Saitek yoke so that it fits under my table without hitting the keyboard drawer. This is based on Zerink's design, with smaller screw head and a larger bulb on top so that the mounting…
This is a remix of El_Terla's excellent work. It's just shorter so it won't hit the build plate when using a cheap MK8 hotend made for Ender 3. Fits right in and uses existing screws. All you need is the printed part. Print in PETG if…
My macro lens needs this to fill the frame better so i modified the 52mm lens adapter and other parts to be much shorter
This is a smaller version of “https://www.printables.com/model/77594-sd-card-grip” because the original one does not work with the cr-10 SD card slot. This works great for the spring-loaded holding SD card slot.
I am using a KlickyNG probe on a Voron Stealthburner on my Mercury 1.1. Based on an Ender 5 pro . I ran in to an issue integrating this into my machine. First, the stock Klicky probe mount extended too far over the print bed, greatly…
I liked the shortened and curved Filler remix, but it still had a completely unnecessary 15mm sticking out for the rolls that I use, which limited my access to things behind it... so I chopped it down even further. It'll now be a real…
Short Clipper Lighter Sleeve With Refill Hole
Same like the original amazing holder but shorter. It will print faster and you will need less material.
Shorter Gamesir G8+ holder for RRTronics extender. settings: .2mm nozzle
The original Märklin C-rail buffer stop was too long for my layout. I made a shorter version that reuses the original buffer. This version has a wall as endpeace. Can be used seperatly.
Just a shorter Version of the Original. Now also fits on smaller thread spools i.e. Gütermann. Works in Pla. Should work in Petg aswell or better. Very good Print For Filament leftovers Pleased rate, Show and Happy Printing!
I just shortened the original model so that it fits all my spools from different brands (up to a maximum of 69 mm (6.9 cm or 2.75591 inches)) so that there wouldn't be as much play and the spool wouldn't move around. If you haven't…
Making the assumption that there will have some amount of weight on it, I've made a very short version of salzig's LACK table stacker model, thickened the walls a bit, resized the leg "receiver" hole a bit and beveled the edge to account…
This design with a much shorter stem works better for me visually. The g-code and the 3mf include the color change. Infill at 100% recommended.
Based on Alexander's model, but made it shorter for better air circulation inside the PolyDryer. Also my lid has smaller opening (you can use my tray with the original lid). Ready to print. You do not have to change the layer settings.
This mod was created to replace stock springs with softer ones. It's hard to find springs with the same lengths so I changed cable strain relief to compensate smaller length of the springs. Stock spring: wire diameter: 0.8mm length: 12mm…
Made it 2.5mm too short because my probe was too low, causing it to scrape against the bed. Also added some holes for the probe's mounting screws.
This thing enables you to use shorter belts in a printer with the traverse bar mounted on the lower side. This is a remix of https://www.thingiverse.com/thing:2782170 which is a remix of https://www.thingiverse.com/thing:2347849 Update…
I wanted a handle with a similar form factor as a condenser microphone, so I could use it with a traditional microphone arm, or to handle it myself while talking to the camera. So I went and remixed one of the models by @365Prints…
Bambu Labs AMS Helper Slightly Shorter than dkarjadi but taller than the other remix and support for front silica gel.
I needed shorter Cable Ducts for my build, so i created this Hackjob in Prusa Slicer...
I wanted to be able to read the paint colour names on Army Painter Fanatic colours so made the wells for the storage a tad bit shorter to make it possible to read them. Print settings I am using for sturdiness: infill: 50% perimeters: 4…
Shorter 105 mm and Longer 205 Hexagon versions of Universal cordless Drill Holder/Mount (Makita, DeWalt, Bosch, Festool ...)
the voron legacy gantry is unecessarly long when not using the stock probe. this shortens the gantry by 14.85mm (which is a lot !) and include a built in klicky NG. this makes the center of mass closer to the linear rods making the…
Did you buy a Derya TM-22 with the long handguard, and immediately find yourself wishing you had the short handguard instead? This handguard has M-LOK slots on the top, bottom and sides, including a half-size slot for mounting…
Shorter LCD supports for the Prusa i3 MK2S to make it fit better into my lack enclosure. I found that even with the 45° heatbed cable support ( https://www.thingiverse.com/thing:2862941 ) the Prusa i3 MK2S is too big to fit inside the…
The original Märklin C-rail buffer stop was too long for my layout. I made a shorter version that reuses the original buffer. Changed the main stl so you can split it into parts for more layer controled color changing.
Please give it a ❤️ if you like it 🥰 I designed this BLTouch Mount for my Ender 3 because my chinese hotend is shorter than the original one. The nozzle was never touching the bed even with the BLTouch retracted and upped at the maximum…
Printable mesh screens with two patterns I printed mine from ASA and then acetone vapor polished them so they look nice and shiny. Antenna Printed standing up from PETG because it can be bended a little. Enable arachne wall generator for…
I wanted to try Luke's toothpaste squeezer, but noticed it was designed for big tubes, and the toothpaste I use come in smaller, 45mm wide tubes. The already existing remixes didn't really provided what I wanted. So here's my shorter…
Gridfinity bin for 4 soldering tips. Size 3x1x3.
I made the back of my 12428 shorter and designed another battery cover / spare wheel roof holder To be attached with small zipties, refer to the photo. When closed in clicks in between existing beams Category: R/C Vehicles
For my needs I make some improvements: Lid now can be 6mm high inside from previous 13mm 1. Lid changed for more parameters - see screenshot 2. On the back - hinge reinforcements moved to outside for wider hinge (red circle) 3. Added…
This is a dirty remix of the original: I cut most of the guide's length so the filament isn't too constrained inside and can slide freely. A bit of warning though: I haven't bothered re-printing this because I sawed the original I had…
Original Author: meyo Original Author Profile: https://www.thingiverse.com/meyo/designs Original Design: https://www.thingiverse.com/thing:1467090/files THIS DESIGN IS NOT ORIGINAL AND HAS BEEN MODIFIED FROM THE ORIGINAL. THE LICENSOR…
This pulley holder allow to make belts shorter. This will help to improve print speed and quality by redusing resonanses.
I have the Sliceworx KP3SProS1. Wanted to use this cable tension reliever. The screws on my bed were too short to reuse the existing nuts with LMaker's awesome heatbed cable cover. I modified it a bit, removing a little from the model so…
As the name suggests, a mod to make the ABXY button on the Cyclone 2 shorter to press. I made some from 0.2-0.4mm thickness, try what best for you. I use 0.2mm on mine. Modeled as accurate according to my caliper measurements. The printed…
Creality Hi Front cover shorter version shorter version of Nora's cover for better view to nozzle used Screw M3x12 and M3 nut Print settings 0,2mm layer 5 walls 15% infill for main body use overhang optimization no supports (only for…
![Rode Wireless Go Handle - Shorter and Thicker (Condenser Mic Form Factor) [remix]](https://media.printables.com/media/prints/708849/images/5560717_ae14a831-061b-4090-9d33-a60d35514964_04cd4bb4-c195-4a5b-b810-5629f3b2daa1/perspective.png)
