Liczymy pasujące modele…
This is a replacement muzzle for the Nerf Stryfe X that gives it an N-Strike barrel lug so it can use Nerf barrel extensions. For printing this part, I recommend orienting it muzzle down and with tree supports for the best results. If you…
A remix of Ultrasonic2's “Nerf Stryfe Trigger V5” for use with microswitches I removed a lot of parts that are not requiered if you want to use a microswitch. I recommend you use supports. This i a remix of a model by Ultrasonic2 .
customized and slightly edited stryfe battery door. (slightly elongated and hook feet chamfered) best printed logo side to the top using supports to make the top a nice surface Category: Sport & Outdoors
A replacement Stryfe pusher. Also works with any blaster that can take a Stryfe pusher. No additional hardware required! This is designed to print without added supports.
UPDATE JUNE 2ND 2026: Geometry has been updated again to match V2.1 of the Stryfe Geared Pusher Kit UPDATE APRIL 3RD 2026: Geometry has been updated to match V2 of the Stryfe Geared Pusher Kit Added a slim blade trigger, for a cleaner…
UPDATE FEBRUARY 17th 2026: The cages have actually been tested in more than just the Stryfe, and updated to fix glaring issues with compatibility with a few blasters. Cages have been made modular, adding 3 options for adapting the cages…
just a raised rail for the NMC kit. to merge the rear and middle together i jankily cut a hole in the middle peice and drilled a hole in the rear to mount a screw that i just hooked between them, works well enough but i have no guarantees…
A replacement Stryfe pusher. Also works with any blaster that can take a Stryfe pusher. No additional hardware required! This is designed to print without added supports.
The Stryfe Rev Switch Mounting Plate is a 3D-printed mod part designed specifically for modding the original Nerf Stryfe. It allows for a very simple installation of an upgraded rev trigger. This is designed for the 21A Omron and Tezuo…
These Stryfe Expanded Battery doors are alternative battery covers for modded Nerf Stryfe flywheel blasters. Available in two sizes, this part is a perfect companion to use with 3S LiPos up to 1100mAh. The Modulus Stryfe requires a small…
Description : I wanted an accuracy device for my Stryfe, and I needed to decrease the FPS a bit. I tried some PCARs and even a NStrike lug BCAR, but was not thrilled with any of the results. That made me think of other ways to mount it…
A remix of Ultrasonic2's “Nerf Stryfe Trigger V5” for use with microswitches I removed a lot of parts that are not requiered if you want to use a microswitch. I recommend you use supports. This i a remix of a model by Ultrasonic2 .
I made the nub smaller and shorter so it doesn't catch on the magazine. There are 2 versions. One is only slimmer and the second one is allso smaller. I dont know how to make it 2 files so both models are in the same file. Print at a…
I wanted to convert my stryfe to half darts, but couldn't find a pusher that I liked, so I made my own! Some notes: Not compatible with unmodified daybreak cages, since their dart guide interferes with extended pushers. You can fix that…
It replaces the front barrel piece of your nerf stryfe to allow for M-LOK rail attachments. No supports needed :)
quick little tinkercad muzzle for the stryfe x, has lines to add spin to the dart
The original model from Jerry's Random Stuff didn't quite fit in the stryfe, so I made some adjustments so that they'd work. You'll still need the original lever pin, pusher head, and pusher pin from the original model. You'll also need…
Have a pesky long pic rail accessory you want to attach to a nerf blaster (especially under barrel on a Stryfe)? Here you go! I have printed it standing up with settings for strength. Touching build plate supports only.
Mag release lever replacing the standard button on the Nerf Stryfe. There are two versions, a short and an extended one. STEP-Files are included. Print Settings Supports: No Infill: 20% Notes: If you experience many blobs on the surface…
An extended version of my battery cover for the Nerf Stryfe. Adds about 13mm additional space. STEP-files are included. Print Settings Supports: Yes Notes: Keep the orientation as it is for a cleaner outer surface, or turn it upside down…
This Butt-Plate for the Nerf Stryfe covers the Stock-Attachment-Point, giving the rear end of the blaster a cleaner look. The design is low profile and has a small integrated slingmount. The Butt-Plate can be secured with a short M4 screw…
A cover for 180-sized flywheel-motors for the Nerf Stryfe. There's a rather large flat surface in the middle which can be used for custom names and logos. I recommend printing it outside up with support at 0.2mm layer height to get a nice…
I took Blasterforge's design for the Stryfe bottom rail and made it slightly longer so it sits flush with the magwell. This also adds a bit of railspace. All credit for this goes to BlasterforgePH. Update 14.01.18- I've included a second…
A simple battery cover with chamfered edges for the Nerf Stryfe. It adds a few millimetres of space to fit larger batteries. UPDATE 06.13.2020: Included a second version with grooves matching the ones on the Stryfe. Added STEP-files Print…
I love Bobololo style rev triggers, I love my StryfeX, and there wasn't a printable version… Bought some digital calipers, measured it out, added the Gryphons curved trigger, printed it, found out the stryfex has a lip nd it was too…
UPDATE JUNE 2ND 2026: Geometry has been updated again to match V2.1 of the Stryfe Geared Pusher Kit UPDATE APRIL 3RD 2026: Geometry has been updated to match V2 of the Stryfe Geared Pusher Kit Added a slim blade trigger, for a cleaner…
Replacement battery doors for your Stryfe X, to make it compatible with hobby batteries, while maintaining the aesthetic of the stock battery This is designed to print without added supports
This is a basic extended battery door for the Nerf Stryfe, based on the one designed by Tarik that Out Of Darts sells. I found that the OOD version didn't allow for the Worker collapsible L-shaped folding stock to fold completely flat…
Lower fill for Nerf Stryfe featuring standard picatinny rail. Tight fitment, and also includes a hole for one coarse thread M3 screw. New version requires both “M3” parts and is installed by replacing the N-strike accessory attachment…
Modified pusher to clear flywheel cages with dart guides. Used in conjunction with Talon compatible cages by ahalekelly ( https://www.thingiverse.com/thing:2843287 ) Feeds perfectly using Worker Talon Adapters designed for flywheel…
UPDATE FEBRUARY 17th 2026: The cages have actually been tested in more than just the Stryfe, and updated to fix glaring issues with compatibility with a few blasters. Cages have been made modular, adding 3 options for adapting the cages…
just a raised rail for the NMC kit. to merge the rear and middle together i jankily cut a hole in the middle peice and drilled a hole in the rear to mount a screw that i just hooked between them, works well enough but i have no guarantees…
A NEW VERSION IS AVAILABLE! https://www.printables.com/model/1739852-stryfe-talon-adapter-v2 Stryfe Talon Adapter: ------------------------------------------------------------------------------- * Based on "Talon mag adapter body…
The Stryfe Rev Switch Mounting Plate is a 3D-printed mod part designed specifically for modding the original Nerf Stryfe. It allows for a very simple installation of an upgraded rev trigger. This is designed for the 21A Omron and Tezuo…
The Stryfe Rev Trigger "Bobololo" Style is an alternative rev trigger designed to drop into modified blasters for use with aftermarket switches. The pusher is the same length as the stock, so if you need it shorter, you can easily cut…
These Stryfe Expanded Battery doors are alternative battery covers for modded Nerf Stryfe flywheel blasters. Available in two sizes, this part is a perfect companion to use with 3S LiPos up to 1100mAh. The Modulus Stryfe requires a small…
Description : I wanted an accuracy device for my Stryfe, and I needed to decrease the FPS a bit. I tried some PCARs and even a NStrike lug BCAR, but was not thrilled with any of the results. That made me think of other ways to mount it…
Allows the Stryfe to fire short darts out of the AF Pro Adapter, which historically does not work with standard hybrid pushers as the mags are set further back compared to a Worker adapter. Consists of two parts - a revised hybrid pusher…
Both of these cages require shell cutting. For the regular cage refer to the Banned Blasters video on shell cutting a Stryfe. For the BCAR version, extra shell cutting is required near the front, as well as some for the front muzzle…
TEST FLIGHT: h ttps://youtube.com/shorts/oiSVrfM4jPY?si=SMwh-cmVWzysh2-i A drone I designed using Fusion 360's Generative design tools. Instructions: Screw the bottom onto each arm - 8x m4 screws Screw in the camera to the camera mount -…
The Stryfe Paddle Magazine Release is an alternative drop-in mag release that improves on the standard button release in the Nerf Elite Stryfe. Additionally, the lever has smooth ergonomic edges, making it more comfortable and easier to…
The Stryfe Heel extends the trigger grip of the Nerf Elite Stryfe to fit adult hands. Luke has always had a problem with his hand sticking off the bottom of the grip, so this was the perfect solution. It fits very snugly with a hidden M3…
Stryfe XL Pusher for Short Darts. Note that this ONLY works with short darts. Converts your stryfe to work with standard short dart magazines without needing a new adapter! FEATURES: • Stryfe XL Pusher • Designed by Tarik • Works with all…
After 2 years of not touching my original design, and a long pitched battle against my children this past weekend, I decided it was time to finally update my original Stryfe foregrip. This is the MK2, which makes some changes to the…
I created this after printing a couple of different designs from here and finding them either too small, uncomfortable, or poorly fitting. This is the initial version, and still being revised. UPDATE 1: First print had tolerance issues…
After going through a Stryfe where I botched the switch mount, went from hot glue to epoxy, and had an overall mediocre time, I looked into developing a printable switch mount. Its friction-fit capable nature was inspired by Out of Darts'…
Re-hosting some of my more popular designs from Thingiverse. [NOTE V2]: Redesigned the entire foregrip section to fit around the Stryfe magwell instead of forming its own foregrip, along with all the aesthetics. This was originally only…
Modified the fly wheels from the Blaster of my son, i replaced one with this part printed in PLA, result is better firepower and less sqeezing of the darts. Print instructions I use PLA and 0.20mm layer high, PETG will work fine too.…
Love the switch plate, just made some shims to bring up the switch (in my case to allow the manual trigger lock to stay with a 1mm shim) Note: to be used with https://www.thingiverse.com/thing:2832479 Category: Toy & Game Accessories
A little plate to keep wires and connectors out of the pusher mechanism space in a nerf stryfe. Print, Glue in ......Profit. Category: Toy & Game Accessories
A quick remix of the following model: https://www.thingiverse.com/thing:3868513. Full credit goes to the original creator! Removed watermark and increased the thickness of the model's thin wall. Install with M3 bolt cut to appropriate size.
The model isn't the cleanest, as I modified it by adding parts in prusaslicer, but it prints just fine.
Designed in on-shape print with your normal setting. This switch plate design was inspired by out of darts but I added a peg so that the switch can just click in. You don't even need to use glue with this design. Otherwise, enjoy this…
3d printable stryfe full auto kit just need a cheap geared motor enjoy. Category: Hobby
A printed Pusher so your Stryfe or other compatible Blaster can shoot Half- and Full lenght Darts. Print this flat agianst the Bed. A 0.2 layer height should be suffiecent. 2-3 Walls/Perimeters and 10-20% Infill. I printed mine out of PC…
I wanted to try designing Nerf parts. Here is my first attempt. Stock has 4 pcs. -Stockplate: connects to N-Strike Nerf end. Allows for 3/8 Flat head bolt. 4x location "nubs". -Clips 1&2: lock the stockplate in place. -Stock: connects to…
A hybrid pusher to fire both half-length darts and full lengths from the same blaster! All other designs i found or bought either were too unreliable or weren't compatible with the OFP anti-jam lid. Print at 1% scale Credit to…
just combined the Hybrid Pusher from Pyrotechnic and the pusher from the AutoStryfe mod kit by kitsune109, tested and it works well with worker talons and worker flywheel adapter. Print Settings Printer Brand: Creality Printer: Ender 3…
PETG; 0,15 mm Layer Höhe Taschenlampe hinten aufschrauben zum einführen Taschenlampe: Winzwon HYDE-136 Laser: LASERFUCHS Punktlaser, rot, 650 nm, 0.4 mW, Ø15x67 mm, Laserklasse 1
Added a buffer tube to the already perfect Stryfe Butt Plate
Für Worker Mod Flywheel Upgrade (https://www.amazon.de/gp/product/B07DCR7LZ2/ref=ppx_yo_dt_b_search_asin_image?ie=UTF8&psc=1) Für die Installation des Mikroschalters war keine Montageplatte mitgeliefert worden, deshalb habe ich sie selbst…
Nerf Stryfe Angled Foregrip Post-Printing Assembly You will need a small screw to hold the grip in place. I used a small wood screw. Category: Toy & Game Accessories
Requires 2x M5x12mm bolts and nuts. Though the friction fit is really good. The fit is really good. Print Settings Printer Brand: Creality Printer: Ender-3 v2 Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 20% Filament: eSun PLA+…
Here we have battery doors for the fake Stryfe (sold under names such as “Bonbell” and “FoMass”). There is both a normal verion (which is a direct replacement for the stock part) and and extended version which gives an additional 16mm…
An improved Rev trigger with switchplate for mounting a DC2 style switch. Uses a real spring, instead of the terrible feeling stock plastic garbage Hasbro cheaped out with. The F3D files have parameters for spring size on the rev trigger,…
Compatible with Nerf Stryfe Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Prusa Polymers PET-G Orange Category: Toy & Game Accessories
A improved version of Ultrasonic2's "Nerf Stryfe Trigger V5". I added a cutout in the back and shortended some other things which interfered with the stock shell of a Nerf Stryfe. This i a remix of a model by Ultrasonic2 .
Dual mag/clip holder for nerf stryfe or most other nerf N-strike guns. Print Settings Printer: Prusa i3 Rafts: Doesn't Matter Resolution: .2 Infill: 40% How I Designed This Using windows 10 built in editor Category: Toys & Games
See hivemonkey.com for the full project writeup, including electronics, code, Stryfe modifications, etc. This is a case specifically designed to fit on the left side of a Nerf Stryfe and mount a particular homebrew electronics package,…
I couldn't find a body kit for the Nerf Stryfe that I liked so I designed my own. There are two versions of the main body. “Body” is as pictured, and “Body2” has thur holes where the indentations are. You will need supports for the…
This is a remix of a file, that I found [cannot remember where from] to fit the Stryfe and Gryphon. When i find the original file I'll link back to it.
I needed a trigger to use with my full auto Stryfe build which uses a trigger return spring so I just added a slot for the spring. Print Settings Rafts: No Supports: Yes Resolution: 0.16 Infill: 100% Filament: Bambu Lab PLA Iron Gary…
Untested idea I had (Still waiting for parts to come in mail). Thought it could be nice to experiment with various accuracy inserts into flywheel cages (Various amounts of striation, degree, ID, smoothbore, length etc.), and I wanted an…
A while back, I posed on r/nerf asking what blasters they'd like to see me design into a LEGO accessory. There were a lot of good suggestions, but one that kept coming up was the Nerf Stryfe. I was reluctant to design it at first, mainly…
I created this after getting my own Stryfe X. Uploaded a blank plate and one with raised darts for anyone to print their own. Please do not sell these prints for anything more than filament (which it takes practically none) I attached a…
I made the nub smaller and shorter so it doesn't catch on the magazine. There are 2 versions. One is only slimmer and the second one is allso smaller. I dont know how to make it 2 files so both models are in the same file. Print at a…
A repost of my first design . It's an handgrip designed in two versions: one for the Worker Swordfish and one for the Stryfe. To attach it to the blaster i used a bit of sticky tack jammed in the rail.
I made this for myself, but I also wanted to share my set up. please comment and make. Thank You! (Details Below)
IMPORTANT: The most recent batch of Plus motors is no longer compatible with the Ultrastryfe cage, due to the change to a square base. Until a version of the cage for square base motors is available, I do not recommend trying to build an…
This is a faux silencer for the Stryfe. It'll work for anything but it fits best with a Worker body kit. You'll need a barrel from a nerf blaster to slide in to both the silencer and the vector body kit, or print a 18mm diameter tube and…
This cover is designed to extend the space availabled for upgraded motors in the blaster. It attaches with a friction fit however, I recommend using a small amount of adhesive around the outer edges to ensure it doesn't come off during…
"Are you painting a Stryfe and keeping the stock battery tray?" "Do you want to ensure you don't get paint on those pesky battery springs?" "You need the FIB Battery tray mask!" A little something we created for those rare times we are…
