Liczymy pasujące modele…
This is my very simple but nice looking SlotClock. It's based on an ESP8266 and ESPhome firmware. It can display time and different animations. Please take the ESPHome firmware as a baseline for future additions. The provided .step file…
Entworfen bzw. angepasst im Rahmen des „ PrintClosure Project “. Das Modell dient der Führung des Filaments, speziell bei vollen Rollen. Es verhindert, dass das Filament von der Rolle springt. Nähere Details sind hier zu finden.…
Das Modell ermöglicht es, das Filament in das Gehäuse des „ PrintClosure Project ” zu bringen. Der Deckel meines Gehäuses ist 3 mm dick (ich habe Acrylglas verwendet) und es ist eine Bohrung mit einem Durchmesser von 14 mm erforderlich.…
Just a repost of original part. I have use it for my Little Green® ProHeat
Dies ist eine Halterung für diese LED-Streifen . Sie ist beweglich und kann somit blendfrei eingestellt werden. Der Druckraum des „ PrintClosure Project “-Gehäuses ist sehr gut ausgeleuchtet. Die ca. 11 W/m starken LED-Streifen werden mit…
Um die LED-Beleuchtung des Gehäuses zu schalten, habe ich Montagematerial für diesen Schalter konstruiert. In die Seitenwand des Gehäuses werden Bohrungen mit einem Durchmesser von 26 mm und 3,5 mm angebracht. Das einfache Schutzgehäuse…
Diese Halterung wurde für das schwarze Netzteil des Prusa MK3 entwickelt. Damit kann es außerhalb des Druckergehäuses befestigt werden. Wie die neue Kabelführung aussehen sollte, lässt sich gut aus der mehrsprachigen Anleitung von Prusa…
Es handelt sich um eine geteilte Kabeldurchführung, die die Kabel vor Beschädigungen durch scharfe Kanten schützt. Ich nutze sie für das „ PrintClosure Project ”, um den Kabelstrang des Netzteils nach außen zu führen. Die Acrylglasplatten…
Im Rahmen des PrintClosure-Projekts , bei dem ein Druckergehäuse gebaut wurde, habe ich diesen Einbaurahmen entwickelt. In den Rahmen kann das digitale Thermometer-Hygrometer eingeklipst werden. Der Ausschnitt hat die Abmessungen 46,5 x…
Um diesen Lüfter und diesen HEPA-Filter im „ PrintClosure Project ” nutzen zu können, habe ich den Rahmen des „ Advanced Filtration Systems ” angepasst. Der HEPA-Filter wird über einen Bügel befestigt und ist mit Schaumstoffstreifen (5 x…
Hello! This is a simple mount for the Wii Sensor Bar from Nintendo. It is designed to clip onto the sensor bar and sit on top of your TV with minimal tilt. Due to angular design of the TCL TV back, this will have a very slight sag (~5…
Hinweis: Aus Sicherheits- und Haftungsgründen dürfen Arbeiten an 230/120-V-Netzspannungsanlagen (Niederspannung) grundsätzlich nur von qualifizierten Fachleuten ausgeführt werden. Note: For safety and liability reasons, work on 230/120 V…
Replacement directional buttons for Roku tv remote after my dog chewed the original ones out of it.
just a case step file contains the model, in case anyone want to adjust. 3mf file include a modifier so that a metal ring can stick that makes it compatible with magnetic holders. the top and bottom layer are removed so that infill…
The stock remote for my TCL Q5 series TV was too thin and slippery. Being black it was also hard to see in the dark. Printed this sleeve in Glow In the Dark PLA to find it easily. I believe it should fit models RC923A FMB1 / RC813A FMB1…
Saw there was a ROG Ally version of the Joydock mount but nothing for the Steamdeck. Saw the Deckmate and the Mechanism system of mounting. Put them both together and you get a universal way to mount your Joydock! Very impressed with the…
This is a Mount for the Goove TV Backlight 3 Lite Its for the TCL Q7C, 50 Inch, but i think it should also fit bigger versions. Just a bit of support needed for printing and a bit of double-sided tape to fix it in place on the TV.
Provided only with the "plus" models, the HydroRinse allow to clean the hose after usage. This is a remix of an existing model to add an hose mount. https://www.thingiverse.com/thing:5920816
A simple remote holder for TCL brand Roku smart TVs. Mounts with either two screws or adhesive similar to a command strip. Category: Organization
This is a mount for a Nintendo Wii Sensor bar for TCL TV (C725) This may work for another models too, only C725 tested.
45° Hinge for my PrintClosure project. M3 holes. Two parts are connected by standart M3x20 screw. Left and Right variant included.
Printed Enclosure Project for Prusa MK4/S - PrintClosure Info: External dimensions - 520x520x620 (XYZ) Internal dimensions - 490x580x490 (XYZ) Can be printed even on smaller footprint printers (like Prusa Mini). Uses printed pins and…
Simple handle for PrintClosure Project Uses original holes of the enclosure (M3 Screws)
Simple Logitech Webcam C930e mount for PrintClosure Uses original M3 hole in the corner of the enclosure. Additional: ¼ inch camera screw ( Like this one )
Simple mounting plate for PrintClosure 140mm exhaust fan.
Digital Thermometer/Hygrometer holder for PrintClosure . Made specifically for Iso Trade 9310 , but should fit the same footprint Thermometer/Hygrometers. Installation: support beams connections of PrintClosure (replace one M3x16 with…
You can hang your soundbar on the wall with this. The 001 model has 15mm clearance to the wall, the 002 version has 45mm clearance. If you need more clearance drop me a message and I will add it. Design files:…
I would like to create a holder for the TCL C84 remote, unfortunately, the C84 remote is larger, so I will create a new model, but I don't want to toss this version. Happy printing!
Objective: The objective is to build a replica Ghostclip with a partner using the software, solidworks, checking in at each individual step while making sure you and your partners ghostclip's are identical. The Construction Instruction…
Designed to fit with friction fit. A slice of innertube positioned on the seatpost helps to keep things snug. Printed in 0.2 with PCTG This is for a 38.9mm Clamp, so it is quite big, it won't fit just any bike. I also use a seatpost with…
I recommend PETG or ABS/ASA. PLA could theoretically work, but I didn't have the balls to try it. It may or may not fit other TCL models.
Designed based of the datasheet for the TCL6 and tested to secure fitting. Print it standing to avoid any supports necessary, 3-5 walls for strength and 30% infill. Feel free to support me @ https://buymeacoffee.com/swagga5aur
Inspired by the soapbars presented in “David Fincher's - Fight Club - 1999” you can now make your own Prusa Printers Soap bars with this 3D printable mold. Printing instructions: Print the base in PETG, ASA or ABS (This due to it's…
Simple case for a TCL K24 phone. TPU, tree supports(for the button/plug openings)
I usually store my belts rolled up in a drawer or on the sideboard. However, rolled-up belts tend to unroll, eventually leading to a mess. This clip is my solution to the problem. It keeps my belts neatly rolled up, making them easy to…
The original version of this model was uploaded by gawdzilla on Thingiverse. I extended the model, added spaces for 2 more accessories, and relocated the screw holes. Really helps clean up the closet shelves!
I shortened the length of the upper plate by 18cm. This smaller plate was framed with the (door) elements 2x Z1; 2x Z2; 2x E1 and 2x E5_12cm and attached with the hinges (as with the doors) to the rear Y1 / Y2 parts using M3 inserts. The…
Godin Nightclub pickguard and truss rod cover
Reuse your existing VESA mount for the TCL 55", 65" and 75" Class A300W NXTFrame Series TV. Attach the TV to the upper holes in the VESA mount and use these brackets to secure the bottom. Works with 55A300W, 65A300W, 75A300W I suggest a…
Overview This model holds your TCL TV's remote. It slides over the (~20mm thick) horizontal boards of most college dorm style adjustable bedframes. It works by first cradling the bottom of the remote, with a snap fit as the rest of the…
Looking for a better way to display your Ulanzi TC001 Smart Pixel Clock? This 3D-printable, clipsable support is the perfect solution. Designed for ease of printing and assembly, it provides a stable and secure platform for your clock.…
Ich verwende den Clip für meine 1,75er und 2,85er Filamente und man kann Sie zwar in einer Schachtel zwischenspeichern, aber wozu hat man einen 3D-Drucker…? Also habe ich einen Speicher/Spender designed… Ich habe es beschriftet designed,…
I designed these legs after I lost mine. It took a couple hours so I imagine if anyone (unlikely) will ever need to replace the legs on their 32" TCL TV with the model number 32S305, I'd share the file and save them a little time. If…
This is a sound deflector designed specifically for the TCL 40S350G television, but may work on other models with similar leg/speaker design. It redirects the sound from the TV's downward-firing speakers forward, improving audio clarity…
As requested and test printed by u/weeb-splat .
The rolling rack in these dishwashers is made of wire and is plastic coated. After use and abuse, the plastic coating gets broken, water is introduced to the steel wire structure and that structure rusts. If you let it go, pieces can…
Provides hassle-free hose cleaning of the Ryobi SwiftClean Mid-Size Spot Cleaner. It rinses left behind debris for hassle-free hose maintenance by using the already abailable cleaning solution inside the spot cleaner. Just attach this…
The relevant model TCL Breeva A2 air purifier is made to stand above the ground. It keeps it away from dust and particles. You should use 3 screw for mounting model or you can prefer fast adhesive.
I tried to make this model as: easy printable/assembled as posible. Requiring minimal aditional hardware and posibility for easy modding. With right print setings it shoud also be reasonably sturdy Recomended as manny walls as possible…
This is a sorta Beltclip/case for those new Casette players that are still made today. This is designed specifically for the Taperoller plus from Dirttapes, I have the old MiniUSB version, feel free to tell me if it doesnt fit the USB-C…
I drew this in Fusion 360, you will need some small screws (shaft 2.5mm or less, head 5mm or less) to mount it to the wall. I first drew the large and small remotes and the placement of the buttons, then offset that and added some nice…
Hello, Welcome to my profile, full of models and miniatures :-) I have a Belt Loop for Keys for you. The ideal solution when you don't have pockets but need somewhere to put your keys. One part of the loop can be put behind your pants or…
Hallo, ein kleiner helfer der meine Rosen hebt,ohne binden zu müssen ;) Print Settings Printer: Anet A8 Rafts: Yes **Supports:** No Resolution: 0,15mm **Infill:** 25% Notes: I just printed it flat on a glasbed with PLA. Category: Outdoor…
A basic 3d-printable model of the beltpiece worn by various characters from the anime Sword Art Online in GGO made by commission
This is my mount to put my Pan Cam v3 on top of my TV, the two tabs lock it in place on top of the tv, simply put the two tabs facing down on top of the TV and the Wyze Pan Cam v3 sits right on top. There is a cut out to accommodate the…
Sound deflector for TCL 43C655 TV speakers. Partially solves the issue of poor sound caused by incorrect speaker placement. It inserts into the speaker slots and directs sound toward the viewer, while fitting precisely to the height of…
This is my very simple but nice looking SlotClock. It's based on an ESP8266 and ESPhome firmware. It can display time and different animations. Please take the ESPHome firmware as a baseline for future additions. The provided .step file…
It would be nice if you post your make. Thank you
Description: The BitClip Mini is a compact and minimalist bit holder designed for the TheSummit wallet by @revere521 , a 3D printed wallet that uses rubber bands to secure cards and cash. It was designed in Fusion 360 and adds everyday…
This is a replica of Scanlan's Nightclub Key from the show "The Legend of Vox Machina," made by Critical Role *spoilers for seasons 2 and 3 He/Vex found it in Umbrasyl's horde after Vox Machina killed him in the season 2 finale. The key…
Esse é um suporte de controle que fiz, para fixar controles desse tipo em suportes para TV. Para fixa-lo utilizei lacres de nylon.
Simple TCL TV remote hanger. Mine was printed in PLA, I think any material will work. I printed in standing position with only minimal tree support.
Holds five (5) airsoft shotshells in a clip that can attach securely to your belt or webbing. Prevents shells from falling out while running, crawling, or maneuvering. Do you reload with your left or right hand? There are two options to…
Stable and rigid riser for the TCL Q77k TV. The original stand sinks into the slot for a stable and rigid connection, surface area of contact with the cabinet is increased to prevent sliding. Height increased by 7cm.
✨ All models available in my shop are carefully designed with 3D printing in mind. ✨ I understand how valuable your time is, which is why all models are ready for immediate printing, optimized for a seamless printing process. 📦 My designs…
This is a short stand to be used in place of the supplied stands so that the TV sits as low as possible on a desk. I use this TV as a monitor and need it to fit on a desk under a shelf. This leg provides the shortest height possible. Can…
Heavily inspired by @Quesabyte 's design. https://www.printables.com/model/570584-pokemon-go-plus-belt-clip I wear this on my wrist attached to my watch strap though and it would fall out of the clip when I bump my arm. I built this model…
Fast and simple TPU printed belt clip for TCL kids watch as a replacement for the broken one.
Needed to rise my 65 in TCL tv 8cm to fit a center speaker under it. I didn't find sturdy solutions online on printables so i made my own. Print in any material, with standard settings and one of these will handle a human easily. fits…
Replacement belt clip for Crawford Remote Print it oriented like in the picture.
Upgraded clip for the best grip and made a half version for light look.I tried on 91mm so If you are going to use it on a larger model, you can use the half version.
Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately) Category: Replacement Parts
This is a shelf for the IKEA Skadis board I designed for holding two Milwaukee M12 batteries. This shelf is wide enough to hold the XC batteries as well as the standard M12 battery. This print utilizes the T-Clip System from user Line Arc…
This is a battery holder for the IKEA Skadis board I designed that holds a Milwaukee M18 battery. This print utilizes the T-Clip System from user Line Arc Line which allows for easy and strong attachment and re-attachment to the Skadis…
Der Filamentcleaner „Tube“ ist eine kompakte, einfache und effektive Lösung, um dein Filament vor dem Einzug in den Extruder oder Bowdenschlauch von Staub und Ablagerungen zu befreien. Das Röhrchen hat eine Höhe von 26 mm , einen…
I lost the battery cover for my TC TV's remote control. Designed it using FreeCAD. Interestingly, it was the most challenging design I've attempted since I started messing with CAD about 6 months ago. My final print was in HS PLA. There's…
TCL Klimaanlage halterung fernbedinung für Wand und 9mm RohrTCL Klimaanlage halterung fernbedinung für Wand und 9mm Rohr
Summary Cont. @PaulSmetkov_3771537 and I have designed an organizing device that can clean up your desk space and add a little life to it. Lesson Plan In order to learn and get comfortable with using Solidworks and formulating a plan to…
This mount angles the speaker downward around 28 degrees, and inward around 26 degrees. Mirror the part to print a complimentary Left Rear version You could use the model as Left rear, and a mirrored version for Right Rear to point it at…
This 3d printed piece is for window to TCL exhaust hose connections. I also drop a link for onshape cad file so you can modify it as you wish. Important part is clicking connection to original hose. link to onshape drawing
Replacement battery cover for the TCL Roku RC-AL5 remote control. This model appears to be dimensionally accurate but is a very difficult print. It requires supports at any orientation. If you have a successful print and fit, please let…
Simple holder for TCL TV Remote. Jednoduchý ostojánek pro ovladač TCL (televize). Created in / Vytvořeno v OnShape: https://cad.onshape.com/documents/a820633c18d7140918eb6fc1/w/181bd86c35a384d5563f1851/e/faec00108ea650cf1dbbc22c
Man I hate these buttons. I get that Roku uses their placement for revenue but doesn't mean we can't over engineer a solution to an inconvenience. This is a super fast print and under 2g. I used PLA that was loaded in my CC from a…
Die original Clips verschleißen sehr schnell. Daher wurde dieses Modell entwickelt, welches in jeder Dimension dickere Strukturen verwendet. Das Modell kann in PETG oder PLA gedruckt werden, ggf. sind Stützstrukturen erforderlich. Wenn es…
This is a community project and was designed by me with a lot of feedback from the community. Thanks to all the testers, helpers, and everyone who printed the finished model. More about the Macher Festival: macherfestival.io
These parts fit a generic Diesel heater sold on Amazon under the OMT, Orion Motor Tech brand. It is thin and tall. The legs fit a 167mm base. There are also two parts in there to convert it for a top cover only or top and two sides. This…
This is a replacement TV leg designed for TCL Roku televisions when the original stand is lost or broken. It closely matches the factory geometry and mounting style, providing a stable, clean-looking solution without needing wall…
I designed a TV stand. It will be +9 centimeters higher. For this type, it is good: TCL 65C6K
A simple addition to my other project.(CNC PV panel) I am building a complete weather station using this type of clamp, and I don’t want to unscrew all mounts every time I update or modify a component.
