Liczymy pasujące modele…
Note: the coned center section design saves print time (prior design required individual deposition points for 12 tiny dots that often failed, but that are eliminated here) and provides the strength needed to eliminate the vertical links…
Layer - 0.2-0.3mm Walls - 2 Infill - 15% No support !
WordClock 16x16 - 2024 This is the 2024 variant to the WordClock 16x16 model adding new functions and features as well as a new font as V2 variant. =) This WordClock 2024 variant covers mostly every input I got from users in the last 2…
BIG news on 11.07.2026: WordClock 16X16 received its biggest update yet. I fully rewrote the configuration portal and added lots of new features and improvements to the software. To name a few of them please read this list and have a look…
I didn't like any of the available Designs for Gimbal Protectors already uploaded on Thingiverse so I decided to design my own improved version. Some Key Features I found important: Both Gimbal Protectors connected in the middle, no…
16x16 LED Matrix Frame No glue, tape or screws needed Accessible USB port Wall- or desk-mounted Snap-fit sockets for ESP-WROOM-32, MAX4466 or MAX9814 microphone and DC Power Connector for easy installation Optional socket-less version…
Made from a carefully arranged 65x52x198 mm block of interlinked rings supported together, this 3D print expands into a chainmail sheet measuring nearly 1.5 meters long and 6 centimeters wide. It was printed on a Prusa Core One. See it in…
16x16 LED Matric case Features: Fits standard 16x16 LED matrix Rear hidden power barrel jack Internal supports for panel Lots of space for dev board to drive the LED matrix Its designed to house a ESP32 or ESP8266 running something like…
This remix of the "Skadis continuous shelf" is wider and deeper. Its 223mm wide and 160mm deep.
MAZE RUNNER inspired LED 16x16 matrix clock with 256 NeoPixel LEDs Features: 16x16 matrix clock that you cannot read directly without knowing where you have to look. Some people i showed it had a really hard time to see it and some gave…
The Printables version will not be updated. The best place to get it is here: https://captainbobsim.com/product/the-cessna-172-project-files/?customize_changeset_uuid= Find the MobiFlight code under Section 2/Avionics Bill 'o Materials: 📦…
Intro: The motivation for this design was to build an eGPU with a $250 budget with used parts with a 10 liter maximum volume. At 165mm x 165mm x 330mm, it comes in at 8.98 liters. Full assembly guide here:…
(if you have printed this earlier, as of 12/27/22 there is an entire new version out!) Mini-IFU (v2) Print There are 2 versions of the “Connector_Bottom” you can print (you only need one!). _v2 requires the additional…
Stabiles Scharnier in den Abmessungen 80x55x16(7) LBH Achse Inbusschraube M5x50 + Mutter PLA oder PETG 100% Infill
Mainly used as a replacement for a missing cap on the GX16 connector on my electric scooter. You can trim the end if you want a shorter version, or swap filament before the end of the filet with TPU to make it more water-tight. Print…
A 16-port keystone patch-panel made to fit in 10-inch racks. Mix and match your keystone modules in your mini lab with this model! This model is part of a series of 10-inch rack mounts I've designed. You can check out the others here . Do…
Customized version of https://www.thingiverse.com/thing:82533 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing\_id=82533 Print instructions Category: 3D Printing Tests Instructions Using the following…
UPDATE: I also have done a 32x32 Matrix in a IKEA picture frame with WLED: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa…
BIG news on 11.07.2026: WordClock 16X16 received its biggest update yet. I fully rewrote the configuration portal and added lots of new features and improvements to the software. To name a few of them please read this list and have a look…
A 16x16 base plate with Star Wars cargo terrain to add detail when displaying mini-figures Category: Playsets
Elevate your Dell Optiplex 3050 Micro with these custom 3D printable model files designed to accommodate an MSI RTX 3050 LP graphics card. This set includes: 3D Case : A custom-designed case tailored for the Dell 3050 Micro, providing…
A NeoPixel / WS2812b controlled LED Matrix with 16x16 Pixels Easy to print: Can be printed without support, Filament Type doesn't really matter. I printed mine with PETG, but PLA or something else should work fine as well! I printed the…
Joined gimbal covers for the Radiomaster TX16s radio. These are printed in PLA with a color stop part way. Black Hatchbox PLA: https://amzn.to/3sOiSnG Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
Jednoduchý organizér pro cokoliv. Tento byl dělaný pro makeup, ale použít se dá jakkoliv. Ať slouží… v2 - Pro lepší tisk jsem nahrál části odděleně. A simple organizer for anything. This one was made for makeup, but can be used in any…
Yashica Electro 35 Battery Adapter /Yashica MG-1 (etc etc) After a sucess of previous model (first upload on 5th december 2019), I decide to improve the model by reinforced the adpater. If you have an old camera that uses mercury cell…
bracelet maker i made. 16 and 32 strings versions. this is basically a string holder for braclets from braceletbook.com "Bändelimacher" is swissgerman for "bracelet maker" :)
Lego road plate 8x16 brick - from new Lego City. Not 100% accurate to the original but fits. The posted photo - extruder 0.2mm and 0.2mm layer height. I tried to print it upside down to get nice flat top. However the recessed studs with…
Did not like what I saw on thingiverse. 3D printers don't print very nice in the air, especially when you want ABS, HIPS, ASA, anything other than PLA, so I designed my own, where you can print it out of separate pieces and assemble it…
Protect gimbals and front sticks. New version with upper stick protection! Assembly the two parts with pressure, once in right position the upper part rotates freely. Insert the gimbal protection first, then rotate the other part: on the…
Gimbal Protector for the Radiomaster TX16S I have larger Gimbal Stick-Ends than the stock stick-ends. I wanted a Gimbal Protector that would fit over those but also fit in the Radiomaster TX16S case (the one that comes with the…
Very simple, wire these LEDS; https://www.aliexpress.com/item/4001296811800.html?spm=a2g0o.order_list.order_list_main.89.21ef1802Wp91AO Along with an ESP32 to a 5v PSU, glue the panels together and you're done :)
Updated CAD below. A charge plug protector designed for the Funwheel Controller Box . Should fit a GX16 port with an m16x1 thread to secure it on the port. Tested on a Bambu Labs P1S at 0.08mm layer height for maximum qualityyyyyy. If you…
remake of another model. Added features. Dimensions 170mm x 170mm x 5mm (L x W x H) excluding dovetail counter-sunk m3 holes parts clearance (0.8mm) Features parts clearance dove tail for connecting the four pieces small inlet for the PCB…
Quick mount mobile holder for the Radiomaster TX16s. Holds a mobile phone or similar (63 - apx. 90mm width) for use with Qgroundcontrol and Ardupilot or similar. Hardware: 1pcs apx. 60mm long 4.5mm (max 5mm) spring in tension. 1pcs…
“Years ago" Inspired by all kind of clever solutions at the time, I designed a dispenser for 330ml cans which printed in only 4 pieces on my BIG 3D printer (~450mm x 450mm x450mm) which rests in piece ;-( Luckily the local brewery decided…
!UPDATED!: V2 Radiomaster Tx16s Gimbal protector (also fits for AG01 gimbals) Combined and Single Version Perfect fit with all Materials. I used PLA Please like if you downloaded it :-)
I've been looking for a good box for my TX16S for some time. Either very expensive or just simple polystyrene. Here is my own box. Very easy to print, Rock Solid and Perfect Fit!!! I do not use the internal module. Therefore no fixed…
RGB matrix case Diffuser (print in place with color change) Case stand Back frame to fit esp32 dev boards, mini bread boards, etc Printing Instructions Please use white filament for diffuser. The case & stand can be printed from any color…
Yet another transmitter stick protector model! Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm or better Infill: 5% - 10% Category: R/C Vehicles
Second model published, but the first one i actually started to work on. Diffuser + box for a 16x16 pixel grid (available from BTF lighting). for the diffuser, first three layers are white PLA, then switched to black pla for the remainder…
Plate 2 x 16 This set of building pieces has been developed through reverse engineering and is compatible with LEGO® building systems. Please note that this project is entirely independent and is not endorsed, sponsored, or affiliated…
I wanted to build a nightbed lamp for my kid, but all the previous neoboard-related designs seemed designed to be hang on a wall more than to be used by a 5 year old... so I built a new frame with a wider bottom side. Instructions for the…
1x1x16U Open Bin, works great as a Pencil Cup, or for longer tools/probes.
EdgeTX , a modified Firmware and a Radiomaster TX16 touch enabled screen make it possible for the FrSky Horus X12S radio transmitter to also have touch functionality. The increased thickness of the touch enabled screen though makes it…
Sticks for TX16S M4 (no threads). Good grip for hybrid/pinch style. You are welcome to remix.
Multiplied the original cutter and made it a total of 16 fish.
Gimbal protector for Radiomaster TX16S (MKI or MKII) / Jumper T16 radio (should work, not tested). Protector is from a one piece with a grip for easier removing. LED charging indicator is fully visible while the protection is on. Bigger…
This is my Pult Tray for Radiomaster TX16S transmitter. The parts named "Aloy_..." shall not be printed but rather made of Aluminium for best robustness. The Leather Applications are not required but make it comfortable and look…
Collection of screws (ISO 4017 / DIN 933) including : M16x 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 80, 90, 100 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit…
Based on the rough working principle of the most popular self watering planters on this website. Walls are thick enough so no leaks occur (tested this myself, sadly I no longer have access to the final prints) Theoretically it's possible…
WordCalendar 16x16 - 2024 BIG news on 17.07.2026: Software version V2.0.0 available! WordCalendar 16X16 received its biggest update yet. I fully rewrote the configuration portal and added lots of new features and improvements to the…
This transmitter tray is designed specifically for the Radiomaster TX16S with a folding handle. All parts were printed in PETG for outdoor use: Satin sheet and Kores application 0.4mm nozzle 240C nozzle temp 90C bed temp 15% infill…
Remixed this from AWSW great model https://www.printables.com/de/model/450556-wordclock-16x16-led-matrix-2023-v3 - here you can also get his neat Arduino Software to operate. I only remixed DE+EN Fronts so far, other languages would take…
No supports or brim, and print normally otherwise This is from my makeronline account, so please do not report, BURNTkoki, and this printable account is linked on makeronline
This is a remix of the German Version of the famous and great "Wordclock 16x16 2024" by AWSW (https://www.printables.com/model/768062-wordclock-16x16-2024). So if you need information about the hard- and software needed, please look…
I remix the original handle and put hole for screw and tightening nuts. Use a plug on one side of the handle for a good alignment
Desk holder/stand for all WordClock 2024/2025 ( 16x8 and 16x16 ) models in case you want to lean your WordClock 2024/2025 a little bit back on your desk, sideboard or low board. =) With the shown big printed screw you can adjust the angle…
These are rackmount brackets for the Allen & Heath DX168 stagebox.
Die Pultbasis wird mit dem Rückteil des Senders verschraubt. Ich habe hierfür M3-Einschmelzmuttern in den Druckteilen verwendet. Der Sender muss zur Montage geöffnet werden (4 Schrauben hinten, 2 bei der Antenne) - Anleitung als…
This is for people who want to modify a Time Crisis 1 clone arcade lightgun to use a GX16 connector and their own cable instead of the fixed shower hose that comes with the gun, without having to widen the original hole. Model should be…
Gimbal protector designed for the brand new Radiomaster TX16S MK3 . Tested and validated on the MAX version . This accessory helps protect your gimbals during transport and storage, preventing unwanted movement and potential damage. 📦…
simple cable box 160x160x50 for M3 heat set threaded inserts
For maximum strenght you should print it standing up with supports under the hooks
Cover to protect PCIe cards during storage. This remix adds a new PCIe x8 cover to the original x4 and x16 sizes.
I did this remix to mount accessories into the 3030 profile for Prusa. There is two files: for M3 screw and for M4 screw. Regards! Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 40%…
Collection of screws (ISO 4762 / DIN 912) including : M16x 16, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I…
The first version published here is a rather minimal case with a surprisingly effective diffusor for one of those quadratic LED matrices you can get on Aliexpress with 256 WS2812b LED on it, 16 rows a 16 lights, spaced in a 10mm raster. A…
A very simple gimbal protector for the Radiomaster TX16S with holes big enough grand lotus stick ends Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 200 Infill: 25 Filament: EcoJake PLA Doesn't…
Designed for printing in ABS @250C through a 0.4mm nozzle at 0.2mm layer height. Print with button face on print bed. Supports will be required for some areas, and finishing may be required on the retaining flanges due to the print angle…
This is a simple spacer to keep the 18650 battery holder from moving around and possibly damaging the power cables going into the radio If you ever plan on keeping your radio in your car I suggest you do not print this in PLA. I printed…
This is a 16x16 baseplate circle inspired by lego. Great if you want to mount some lego on/in something round. I also made a 10x10 version: https://www.printables.com/model/865765-lego-inspired-baseplate-10x10-circle And a 11x11 version:…
Updated CAD below. A charge plug protector designed for the Funwheel Controller Box . Should fit a GX16 port with various sizes available if you're having tolerance issues. Tested on a Bambu Labs P1S at 0.08mm layer height for maximum…
A Remake of the original Radiomaster TX16s Battery Cover with TB Logo. Original Make credit to Radiomaster RC. Unable to make this as a remix due to link being unavailable currently. Hope you enjoy. https://techbytes.ca/3dprints/ IG:…
Držák LED Alu rohového profilu 16x16mm pro hliníkové rámy 20x20mm. Koukněte i na mé další modely . Pokud mě chcete podpořit, můžete zde: PayPal , BuyMeACofee , QRCode . Děkuji
Collection of screws (ISO 10642 / DIN 7991) including : M14x 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher…
Standard round 45 degree LED profile end cap used for corner wiring. Has to be glued, doesn't hold otherwise.
Collection of set screws (ISO 4028 / DIN 916) including : M20x 16, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the…
A spacer to keep the 5000 mah lithium-ion battery from banging around in the battery tray. This will keep everything locked in place.
Ends caps to fit in 16 x 16mm angled aluminium extrusions for LED-strips. The LED-bar can get warm, PLA is not recommended as a material to print with. Tight fitting - make sure your printer and extruder are accurate/calibrated.
A parametric LED Matrix diffusor front plate. fullcontrolXYZ based, 100%extrusion, 0 travel, 0 retractions. Extrudes at 0.8mm, which is totally fine for a 0.4nozzle. A bigger nozzle will probably allow much faster print speeds. Prints as…
Use heated inserts (on motor side) to mount this adapter to your motor with 16x16 moutingholes and mount it to your frame with 12x12mm mountingholes. I used M2 inserts and screws to mount everything to the frame and M3 screws for mounting…
I design a compact case for the DISPLAY ST7735S 0.96" 80x160. It includes cutouts for pins and it has guillotine closure. Be sure to have the same model otherwise it doesn't fit as well as you see in the picture. If you need help or you…
FPV drone adapter with 16x16mm to 20x20mm mounting holes
Záslepka LED Alu rohového profilu 16x16mm. Koukněte i na mé další modely . Pokud mě chcete podpořit, můžete zde: PayPal , BuyMeACofee , QRCode . Děkuji
My remix of the original grips, which are more ergonomic for my hands.
The moss should grow outside the grid after a while. I will update the pictures in a couple of weeks.
This is definitely my biggest design project I've tackled so far. After a lot of trial and error it's finally finished and I hope I'm not the only one who has been waiting for something like this. I had seen the funny pixel art displays…
I didn't like how others have the screw protruding on the end, so I designed this one to use some M3x15 socket-head cap screws that I had on hand. It fits the Longs 23HS9430 and probably a bunch of others. I printed mine in PETG at 0.15mm…
This is top plate to install SMA connector in TX16S. Best connector will be one with additional screws on side. For easy print top part is flat. Print requites support.
Collection of screws (ISO 10642 / DIN 7991) including : M12x 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher…
Model Hello, I am sharing my custom slim frame for lithophane photos. This one is created for lithophane size 240x160x4mm. It will not work for scaling. Original file attached, ammend the size to fit yours picture accordingly. Hole for…
Print in TPU with: .2 height random seams (helps with watertightness) bridge counterbore holes as sacrificial layer (orcaslicer) 4 bottom shell layers (helps with watertightness) 10% gyroid infill
WordCalendar 16x16 - 2025 BIG news on 17.07.2026: Software version V2.0.0 available! WordCalendar 16X16 received its biggest update yet. I fully rewrote the configuration portal and added lots of new features and improvements to the…
Inspired by PunongBisyonaryo design. Thanks a lot. Use only flexible filament. Scale: GX12: 100% GX16: 125% GX20: 138% Print Settings Printer Brand: Creality Printer: CR-X Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament: Flex…
I wanted small wall hook for the radio, and could not find good alternative, so here is my own design. This wall mount was designed for CNC-upgrade handle, but should work with the original as well. Print Settings Printer Brand: Prusa…
This is a remix of the 16x16 LED Matrix frame from fractalnoise . I made some modifications required for my own specific use case and to improve the print quality of the back frame itself. I printed the model with PETG and added “mouse…
Update 6/23/22 Created a different lid (Lid v7.stl) and button (New_Button.stl) that is compatible the very nice TFT LCD display holder by design8studio here:…
remixed the original to make it stronger.
Print in TPU vertically with supports and make sure the top layers are slow enough to properly cool. I'm including a .3mf file that I used with my ender 3 that has upgraded cooling. Should work with any GX16 plug but feel free to remix…
![eGPU Thunderbolt chassis for EXP GDC TH3P4 + ATX PSU [165x165x330mm - 9 liters]](https://media.printables.com/media/prints/429812/images/3562411_ec2f4b23-3b18-464a-bc88-986318650ad4/screenshot-2023-03-21-182821.jpg)
![[Drop-in T-Nut] [M3 M4] for 3030 profile (8x16mm)](https://media.printables.com/media/prints/167112/images/1554552_ed444b7d-d86d-4ff4-b1f1-e01709364a83/large_display_img_20190903_233919_167112.jpg)
![Lego inspired baseplate 16x16 circle| Fits HÄRLIGA bell jar[big version] from IKEA](https://media.printables.com/media/prints/865782/images/6646898_ed5a028d-8f81-4c76-9830-e8afd2b6a911_ef37d36e-8498-4f3d-b5da-02c69cda5283/knipsel.png)
