BTT Pi TFT43 V2.0 Voron 2.4 touch screen case ( LED NEOPIXEL REMAKE)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
I made a neopixel led remix of the original made by Kenn226 schreen case for voron2.4.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 5
- Makes
- 0
- Views
- 224
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Voron Parts & Upgrades
- License
- GNU General Public License v3.0
Hi,
A while ago i printed the original schreen case from Kenn226. and used it for a long time .But now i had the idea it would be nice looking if there where some accent lights in the case . So i decidet to do a remake . And i hope you al like it . Its a fully DIY project and is really fun to do .
If you have some questions and/or problems feel free to ask .I will try to respond as fast as possible .
BOM:
CLEAR FILLAMENT (ABS/PET-G)
COLLORED FILLAMENT BY OWN CHOISE (ABS/PET-G)
SHCS M2.5 X 10 (4x)
SHCS M3 X 8 (2x)
2020 ROLL IN NUT / T-NUT (2x)
NEOPIXEL (2x)
SOLDERING IRON
SOLDER
FLUX
WIRING ( a not thick wire you need to get 6 wires thru a hole of 4 MM)
SUPER GLUE /GLUE THAT HOLDS ABS/PET-G
EVT ARDUINO UNO (to test the neopixels)
MULTI MEASUREMENT TOOL (to measure continuity)
EVT DUPONT PINS OR WIRING (to test the neopixels with the arduino)
A GOOD CALLIBRATED PRINTER
PRINTING GUIDANCE:
I used standard voron settings . Al models can be printed without supports and or have build in supports . I used ABS but PET-G will also work . Led defuser L/R are the only parts needed to be printed in clear fillament .
BUILD MANUAL :
Printing the parts
Remove the build in supports from the scheencase
solder 2 neopixels like on the picture . (Be sure you have a long enough wiring and use thé same batch of neopixels for both sides )
Test your neopixels in continuity
Push the wiring thru the respecting holes .
It's verry inportend tot do step 5 before step 7 otherwise you Will not get the wiring thru the respected holes
Crimp thé wiring and put connectors on them so you can couple the Left side neopixels DOUT to the right side neopixels DIN .
Also put a connector to the left side neopixels DIN so you can connect it to your mainboard .
I putted also one to the right side 's neopixels DOUT so i have later the option to connect a other chain of neopixels to it .
Test your neopixels evt with a Arduino Uno and keep them connected for assembling .
Click the defusers in the defuser housings
Click the LED housings in the defusers
Put the neopixels in the LED housings
Place the assembled housings with the neopixels carefully in the Case (put evt a bit of glue for a steady hold )
Be carefully that the neopixels keep giving light so you Know for sure they work after the glue has dryed .
The schreen case is now finished
Put your touch schreen in the Case from the front side . It's a tight fit but Will normaly fit with some wiggeling and having the right tollerances.
Bolt the schreen to the Case with 4x M2.5 x 10 .
Mount your schreen case to your frame .this with 2 x 2020 roll nuts or t- nuts . M3 X 8
Connect al your wiring
Be sure you connect your neopixels wiring to a 5v output pin .
Put in your printer.cfg the correct data to let your neopixels work properly .
Your new LED schreen case is finished .
in my printer.cfg file i put this configuration :
[neopixel rgb_schreen_leds]
pin: PC0
chain_count: 2
color_order: GRB
initial_RED: 0.0
initial_GREEN: 1.0
initial_BLUE: 0.0
initial_WHITE: 0.0
I hope you all like my design :D feel free to ask some questions i will try to respond as fast as possible .
if you want to support me you can do this with following link : https://buymeacoffee.com/xeroprint
Thanks !
Jeroen / Xeroprint
CHANGE LOG :
27/08/2026 - Uploaded model files V1