Counting matching models…
I designed this over-radiator hook to store this folding clothes drying rack (from IKEA) when not in use. I live in the UK and think my style/brand of radiator is called “Kermi”. I included the Fusion 360 file, if you need to modify to…
Print approx. €3.45–€4.22 excl. taxPreliminary estimate for PETGSource material: PET
A split version of gridfinity caliper holder, which can be printed on smaller format printers
A dovetail box to hold a set of Dutch Blitz cards. Design notes: Loosely based on: Sliding Dovetail Lid for 3D Printed Box These fit a set of knock-off cards I bought on AliExpress that measure 88 mm (L) × 57 mm (W) × 25 mm (H). So you…
Overview Rails to slide a Stanley small parts organizer into an IKEA TROFAST storage unit. Each rail is split into two pieces (LHS/RHS) which snap together with a dovetail joint. This was necessary because my print bed (Prusa Mini) is…
The 40×45 cm IKEA NORDLI drawers are the perfect width for hanging file folders. These rails clip onto the sides and provide a ledge for the folder teeth so that they do not turn sideways and fall inside. Design notes The clip tapers…
Design notes I used two magnets—8 mm (D) × 3 mm (H)—to keep the lid secure, so that the precise fit of the lid is not as important. I printed a lid with only 0.1 mm clearance—which is too tight to fit as-printed—because I preferred to…
Designed to fit: Google Pixel 5 w/ rubber case Anker PowerCore Slim 10000 PD If you have a different phone or charging bank (likely) you'll need to download the f3d file to make changes yourself.
Feet to raise the height of an IKEA ALEX desk by 8cm (f3d file included)
This is a replacement for the metal L-bracket included in the IKEA NISSEDAL mirror to mount it to a door or wall. 🔩Extra hardware you'll need: M4x10 threaded insert nut (x4) M4x12 bolt (x4) M4 washer, ~9mm diameter (x4)
What : Tiny end-caps to place on M4x5 grub screws, which then serve as miniature joysticks for drone controller. Why : Faster setup for quick drone flights, by skipping the part where you screw in the joysticks. These obviously don't…
Designed to prevent my pannier bag ( Ortlieb Commuter Two Urban ) from bending into the spokes of the wheel when fully loaded. Included Fusion 360 file, as you will almost certainly need to adjust parameters, unless you have the exact…
Inspired by DJI Mini 3 Pro Hollow Battery Case by gyozamonstah , but wanted something that was easier to print—and also with partitioned storage. I've designed the inside to fit the three extra lenses/filters I carry around, plus a full…
Designed to fit these beakers (Amazon UK). If you want to modify for a different set—see the attached Fusion 360 design—and please share yours as a remix, for others who may have the same set! Design notes I initially tried a simple…
A loading tray for six of the STAINLESS STEEL DOSING CAPSULES (.3G) sold by DaVinci.
This wedge stops the IKEA tray insert from buckling under the weight of items placed in it, and subsequently falling off the "ledge" down into the box below. 💪🏼 Features Doesn't need a zip-tie → just drill a single 16mm hole Slight filet…
A lid that snaps onto the side of these Eono-branded filament spools , allowing you to fill the cavity with desiccant (silica) beads. Dimensions Diameter of holes: nominally 3 mm, but prints closer to 2.5 mm Diameter of spool: 57.5 mm…
Splits MUJI 37×63×12mm polypropylene pill box into six compartments. Prints slightly too large (for a snug fit) so just file off ½ mm or so after printing.
This is a remix of this thingiverse model of replacement feet for the IKEA BRIMNES wardrobe . The main change I made was to add a shallow chamfer to the short sides, to facilitate being slid on carpet. How to print : 3 perimeters w/ 15%…
Designed with a 6° angle so that the watch sits roughly parallel with the pegboard. After printing, you will need to sand down one side of the hook so that it fits. Remix of Garmin Forerunner 230 Command Strip Charge Mount With HRM Clip…
Spacers for a snug-fit of Gridfinity baseplate inside a MUJI PP storage box
Design notes Nests two bicycle keys side-by-side, within the same vertical space. Designed based on this KeySmart unit , with one key for Kryptonite New York U-lock , and another for ABUS Bordo XPlus 6500. 1mm walls seem to be sufficient…
I use the Peak Design Everyday phone case which has a neat little finger loop that keeps it secured to one's hand. The loop folds entirely flat when not in use. Almost too well. It makes it difficult to slip my finger into it using just…
Why I have these High5 electrolyte tablets , which come in a long sleeve. The sleeve has a lid containing desiccant, to keep them dry, as they are hygroscopic. But this sleeve is quite long, and cumbersome if you just want to pack a…
Very likely you'll need to download the Fusion 360 file and adjust the tube diameter parameter base on the tolerances of your printer, filament … and the tubes themselves. Design notes: 20mm height seems to be a good compromise between…
These are all currently available results.
