Counting matching models…
I liked http://www.thingiverse.com/thing:2191646 but wanted a version without the logo and sidewalls. Works great with the Steam Controller and the XBox One S (and probably the non-S version too). Not so hot with the PS4 controller (hits…
A lid to keep your bar keepers friend in its container. Print it top side down, no supports. It's not quite a press fit because popping it off with force gets the stuff in the air and you probably wouldn't enjoy inhaling it. Knurls to be…
With this and a few keystone jacks you can embed a Linux SBC (rpi) in your project and never have to crack the box open to service it. Print panel side down, supports very required. A 0.3mm layer print comes out quite usable. The panel…
M3 mounting hardware. Tried with several generic keystone ports, seems to work well enough.
A pivoting bowden tube filament guide. The 1.75mm guide expects the bowden tube to be 4mm outer diameter and the 3mm guide expects it to be 6mm. Mounts with two M3 screws onto whatever you like, so it should be easy to mount on aluminum…
Turn on supports, print on it's side. If your using an actual wall plate, you should consider using the original, it'll work with most of them and be a little sturdier (wider tabs). Remixed from:…
My own take on the very prevalent angled wago mount. This version has retainer lips on the rear side so the wago can't slide out. Also I think all the others are double mounts. If using this with high voltages or current, you should…
My own take on the very prevalent angled wago mount. This version has retainer lips on the rear side so the wago can't slide out. Also I think all the others are double mounts. If using this with high voltages or current, you should…
1U Mount, sized for #10-32 Bolts and Nuts for the front and #6 at the wall (because that was the prevalent size for 50lb wall anchors at a convenient hardware store). Uses pocketed nuts, so no worries about stripping out the plastic.…
Note: XT30U-F are conventionally power outputs , not inputs. You don't want live pings exposed when the connectors are exposed. So don't use this to power your project. Thanks to niZmo for pointing out this omission. M3 mounting hardware.…
My own take on the very prevalent angled wago mount. This version has retainer lips on the rear side so the wago can't slide out. Also I think all the others are double mounts. If using this with high voltages or current, you should…
Router guide you for use with the flex shaft (and clones). One normal version and one with a flat side so you can squeeze it into awkward spaces. I use it for putting notched holes in Bud Enclosures with a flush trim bit. Don't try to use…
Print, sugru/calk into place, get your floor wet less. Category: Bathroom
A replacement collar cap, easy to grip. Tested on a Milwaukee M12 Rotary Tool, which since it fits Dremel attachments, means this should fit a Dremel too. (No promises, please leave a comment if you find out for certain.) Rev 2 is purely…
For use with the bases at https://www.printables.com/model/429098 use this to push pixels without blisters or agony. I don't have enough drill presses for a work party, but these will get the job done. Way cheaper and better than a socket…
Set exactly the box size you need using the Fusion 360 archive (interior_* parameters), modify your panels and mount plate, and print the perfect ready to go project box. STL for 150mm x 150mm x 50mm and 75mm x 75mm x 30mm interior space…
Print on it's side, use the thickest layer your printer is good at. Use a material that can take your expected ambient heat and has a bit of give. PLA is not recommended. Nylon would probably be the best but I got away with PETG though I…
Works with any of the very common 215x115x30mm platform PSUs, like the CUI VGS-350C, Meanwell LRS350, Mornsun LM350, and others. Recommended hardware: 2 - m4 x 8mm screws to mount the bracket to the PSU. 4 - m3 x 6mm screws 4 - m3 nuts 4…
Nuka Cola bottle cord stop. Spring and plunger from the DRITZ 1-1/4" cord stop (available in black, white, and translucent). Use pliers to squeeze the outer casing on the solid sides of the DRITZ stop while pulling the plunger, should…
Keystone port(s) you can attach to one of the edge profiles. Bring the USB/Ethernet/WebCam/Whatever connectors to the outside of the enclosure. Needs 1 m3 8+mm screw and the keystones of your choice. NOTE: I've marked this a beta version…
A couple simple velcro strap anchors, #6 screws. The single sided mount idea really didn't work out that well for my use case, it ended up rocking back and forth against my paint. So I did a two sided one that works in any orientation.…
A clip for PolyLite spools. Spool Parameters: Diameter: 200 mm Edge Taper: 10° Lip Thickness: 3.9 mm Lip Height: 9.7 mm Lip Indent: 0.95 mm Category: 3D Printer Accessories
The Fusion 360 archive (.f3d file) has a pair of parameters (x_offset & y_offset) that allows you to reposition the PSU inside the case (see image). There's not that much moving room in the case, so watch out for hitting the other…
Mount up one of the common mini round hygrometer/thermometer in your dry box. 1 5/8" Mounting hole with tab slots that keep it from rotating in place. Unlike many mounts, it's gravity resistant! (Tight enough for the tabs to actually hold…
Snap fit enclosure for RPi Camera module v2 with m3 mount on back so you can attach it to whatever, whichever side up you please. m3 nut 8mm m3 screw for the tripod mount, if you have too long a screw you can reverse it so the nut is…
1" = 5' scale 6'x9' Flying Carpet. I used the lovely art from https://www.deviantart.com/sydonz/art/Magic-Carpet-431543088 Solid etch the art, then use these files to cut out the carpet and go. (You can set this all up in one go in…
This is a spell effect ring for the Insect Cloud from the Staff of Swarming Insects ( https://www.dndbeyond.com/magic-items/staff-of-swarming-insects ), it's spider themed because my staff is the spider themed version from Adventurers…
I wanted something like dendad51's adapter ( https://www.thingiverse.com/thing:1372158 ) but I wanted it to mount on top of a faceplate and completely cover the decora cutout. Designed for 6-32 screws and captured nuts. You may need…
I required some huge (3") a mini-bases, saw they were exorbitantly expensive, and cut my own out of some acrylic cast offs. I'd include the source, but if you could modify them then you could make your own. Size is 3" accounting for a…
Use with Boscoyo's Pixel Snap/Push Pliers 2.1: https://boscoyostudio.com/products/pixel-snap-push-pliers-2-1 The 3mf file has my preferred orientations and organic supports enabled. The force on it is mostly compression so I think PLA…
There isn't enough clearance on the bottom of the NBF-32016 to use dual-lock or command strips. Also, they removed the mount screw holes in the EQ13 model. Thus this bracket, it takes the weight of the EQ13, just drop it in place,…
Works with any of the very common 215x115x30mm platform PSUs, like the CUI VGS-350C, Meanwell LRS350, Mornsun LM350, and others. The regular version has 35mm clearance from the bottom to the PSU for a total installed height of 123mm. The…
These are all currently available results.
