Counting matching models…
Used it for EMT conduit legs for a table. Designed to fit #8/#9/M4 screws. Apply your best judgement on printing. For reference, I printed them in PETG with 4 perimeters.
Updated 2025-01-23: see below for details. The french cleat duck hook model is great but I needed something bigger. There is a remix that makes it bigger but that was still not long enough to hold extension cords. The hold part also was…
Used the arms and holders of the “small arm system” from @RostaP 's awesome Multifunction Arm mounting system . Added a split base so that it can stand on itself and a new holder variant which allows for a ¼"-20 screw to hold the webcam.…
Updated 2025-01-25 Added extra long (~2.5in) hook version in the original design. New hook design version with a “lip” to help prevent things from accidentally coming off (that is in addition to the slight angle (1-2 deg) inwards that all…
Two tone whistle from @Zoonke's design by adding an internal separation so that it has two separate and different-sized chambers. This makes it have two frequencies which I feel sounds slightly louder. The interference between the…
Small hook for hanging stuff underneath Closetmaid wire shelves. Designed from scratch with my own measurements, although I did take inspiration from the design Closetmaid Wire Shelf Hat Holder . Thank you, @perryusaf I printed it with 2…
3D printable 608 bearings. If you need a different size bearing, the FreeCAD file is included. Update 2026-04-18: Added a model with half-inch (12.7mm) nominal inner diameter for use with half-inch dowel rods (see photo). It maintains the…
French cleat holder for tape, squares, etc. It was possible to do it with the original hooks but it wasn't that stable. Also, I wanted something that allowed me to stack things further out, if necessary, to free up french cleat space.…
This is a model of a connector bracket for joining two sections of ClosetMaid wire shelving at the front, thus ensuring that they are aligned and can distribute the load. I had some wire shelving pieces lying around and wanted to make…
I lost the pad for one of my Bessey clutch-style 12-in bar clamps, so I designed a replacement. See picture attached or search for GSCC3.512+2K in the HomeDepot website for the exact clamp. I except that this will also fit the same style…
Minimalist stand simply to get the base of the Macbook elevated and provide some ventilation. This resolved the overheating problem I was having and which caused the CPU to throttle down. I designed this for a 2019 16" Macbook Pro with…
Hooks to hold a laptop/tablet on a treadmill. Guaranteed to fit a Sole F80 treadmill (as you can see in the photos), but should fit other models also. The hooks have "teeth" in the back designed to line-up and grab to the back grille for…
All credit goes to the very original design from Doug Kremer . All I did was modify the magnet holes in the “wings” (knife sides) to work with 7x2mm magnets. Print all of the other parts exactly as included in the original design. Why do…
A D-shaped loop to tie off (e.g., with rope or zip-ties) or hang stuff from your ceiling or wall. It attaches to the wall with screws up to #9 / 5 mm. This thing is small 7/8 x 5/8-inch (22x16 mm) but mighty. I printed it in PETG with 4…
A simple vertical drill guide that: uses strong, inexpensive, and easy to source hardware, is sufficiently tall for decent precision, and has a wide and comfortable handle for securing it. All one needs is an angle bracket. I used an…
For 3-way corners where one one piece of extrusion runs through the corner (in the photo, see the piece perpendicular to the view plane), one wouldn't be able to use the original connector because the part that runs inside the extrusion…
Truly extra long (~4in / 120mm) hook variation of my french cleat hooks. It is a bit wider at 24mm and can still be linked to other hooks if needed using the connector in original design. It could be used for holding other things, such as…
I got a Ridgid Cordless Circular Saw (model # R8656B) and wanted to store it out of the way on the wall. The model comprises two main parts, a top and bottom, which hold the saw to a board. You can then attach this board to wall in…
The ZS-X11H are relatively inexpensive brushless motor controller boards, with hall effect sensors and PWM control. The only other mounting solution I found on Printables, did not provide any room for air flow and heat dissipation.…
This is a replacement tip for a generic walking/hiking/trekking pole. There are two parts: a cover part that replaces the one that usually comes with those sticks and covers the pointy/spike tip, and a replaceable tip that fits inside…
The handle of my trusty Radioshack double-sided pick broke, again… I had already super-glued it a couple of times and this time it broke on the other side. It is still super useful, so I figured it was time for a new handle. Quick and…
This is my take on a keys pocket clip. I've tried several of the ones available but wasn't really satisfied with any of them, so I've designed my own. There are several ideas from other creators that I really liked and tried to…
I have a clothes rod in the basement and it was sagging a bit, so I made this to help support it. The model prints flat and then we use the flexibility of the filament/print to insert it around and close on the rod. For the “wrap around…
Simple and filament-efficient print bed holder. Only uses ~150 g of filament. Parts to print Print two of the holder parts, remembering to mirror one of them . The one as shown will be the used for the right-side, and its mirror will be…
Add a big RGB LED matrix display to your Qube 540 case. I had two requirements for this design: It had to integrate with the Qube 540 design, meaning that we see the same kind of ~14mm holes spaced 20mm apart. It still needed to allow…
Slim, minimalist wallet which solves the two main issues I found with several of the minimalist wallets I tried before: They were either designed with a specific number of cards in mind (or one had to print variations every time one…
This is a simple wall bumper that clips itself to tube handles to given them some space and prevent them from scratching or marking the wall (see photos). The bumper prints in vase mode in a few minutes and uses less than a meter of…
A french cleat hanger/hook running parallel to the wall (which is 90 degrees from most hooks). I use it to hold a wide bag with a strap on the middle, that would simply look goofy and take more space that it should had I used common…
These are all currently available results.
